linux-stable.git/drivers/usb/dwc3, branch linux-3.2.y Linux kernel stable tree usb: dwc3: gadget: Set maxpacket size for ep0 IN 2018-05-31T23:30:14+00:00 Thinh Nguyen Thinh.Nguyen@synopsys.com 2018-01-13T02:18:05+00:00 e05562277a05559c66476a1a32b4f43d493544a8 commit 6180026341e852a250e1f97ebdcf71684a3c81b9 upstream. There are 2 control endpoint structures for DWC3. However, the driver only updates the OUT direction control endpoint structure during ConnectDone event. DWC3 driver needs to update the endpoint max packet size for control IN endpoint as well. If the max packet size is not properly set, then the driver will incorrectly calculate the data transfer size and fail to send ZLP for HS/FS 3-stage control read transfer. The fix is simply to update the max packet size for the ep0 IN direction during ConnectDone event. Fixes: 72246da40f37 ("usb: Introduce DesignWare USB3 DRD Driver") Signed-off-by: Thinh Nguyen <thinhn@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> [bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> 
commit 6180026341e852a250e1f97ebdcf71684a3c81b9 upstream.

There are 2 control endpoint structures for DWC3. However, the driver
only updates the OUT direction control endpoint structure during
ConnectDone event. DWC3 driver needs to update the endpoint max packet
size for control IN endpoint as well. If the max packet size is not
properly set, then the driver will incorrectly calculate the data
transfer size and fail to send ZLP for HS/FS 3-stage control read
transfer.

The fix is simply to update the max packet size for the ep0 IN direction
during ConnectDone event.

Fixes: 72246da40f37 ("usb: Introduce DesignWare USB3 DRD Driver")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
usb: dwc3: gadget: make Set Endpoint Configuration macros safe 2017-07-18T17:38:30+00:00 Felipe Balbi felipe.balbi@linux.intel.com 2017-01-31T11:24:54+00:00 5a17ec3ce1d0610ddf84a7136e60e861561bf5ef commit 7369090a9fb57c3fc705ce355d2e4523a5a24716 upstream. Some gadget drivers are bad, bad boys. We notice that ADB was passing bad Burst Size which caused top bits of param0 to be overwritten which confused DWC3 when running this command. In order to avoid future issues, we're going to make sure values passed by macros are always safe for the controller. Note that ADB still needs a fix to *not* pass bad values. Reported-by: Mohamed Abbas <mohamed.abbas@intel.com> Sugested-by: Adam Andruszak <adam.andruszak@intel.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk> 
commit 7369090a9fb57c3fc705ce355d2e4523a5a24716 upstream.

Some gadget drivers are bad, bad boys. We notice
that ADB was passing bad Burst Size which caused top
bits of param0 to be overwritten which confused DWC3
when running this command.

In order to avoid future issues, we're going to make
sure values passed by macros are always safe for the
controller. Note that ADB still needs a fix to *not*
pass bad values.

Reported-by: Mohamed Abbas <mohamed.abbas@intel.com>
Sugested-by: Adam Andruszak <adam.andruszak@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
usb: dwc3: gadget: skip Set/Clear Halt when invalid 2017-06-05T20:13:44+00:00 Felipe Balbi felipe.balbi@linux.intel.com 2017-01-19T11:38:42+00:00 29c49277513d3d13a7c5a4f67fc34d3034c27826 commit ffb80fc672c3a7b6afd0cefcb1524fb99917b2f3 upstream. At least macOS seems to be sending ClearFeature(ENDPOINT_HALT) to endpoints which aren't Halted. This makes DWC3's CLEARSTALL command time out which causes several issues for the driver. Instead, let's just return 0 and bail out early. Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> [bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> 
commit ffb80fc672c3a7b6afd0cefcb1524fb99917b2f3 upstream.

At least macOS seems to be sending
ClearFeature(ENDPOINT_HALT) to endpoints which
aren't Halted. This makes DWC3's CLEARSTALL command
time out which causes several issues for the driver.

Instead, let's just return 0 and bail out early.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
usb: dwc3: Fix assignment of EP transfer resources 2016-04-01T00:54:33+00:00 John Youn John.Youn@synopsys.com 2016-02-17T04:10:53+00:00 87b828c3f0a7e36bde1eb3b9deeb1b5c6d2bfb93 commit c450960187f45d4260db87c7dd4fc0bceb5565d8 upstream. The assignement of EP transfer resources was not handled properly in the dwc3 driver. Commit aebda6187181 ("usb: dwc3: Reset the transfer resource index on SET_INTERFACE") previously fixed one aspect of this where resources may be exhausted with multiple calls to SET_INTERFACE. However, it introduced an issue where composite devices with multiple interfaces can be assigned the same transfer resources for different endpoints. This patch solves both issues. The assignment of transfer resources cannot perfectly follow the data book due to the fact that the controller driver does not have all knowledge of the configuration in advance. It is given this information piecemeal by the composite gadget framework after every SET_CONFIGURATION and SET_INTERFACE. Trying to follow the databook programming model in this scenario can cause errors. For two reasons: 1) The databook says to do DEPSTARTCFG for every SET_CONFIGURATION and SET_INTERFACE (8.1.5). This is incorrect in the scenario of multiple interfaces. 2) The databook does not mention doing more DEPXFERCFG for new endpoint on alt setting (8.1.6). The following simplified method is used instead: All hardware endpoints can be assigned a transfer resource and this setting will stay persistent until either a core reset or hibernation. So whenever we do a DEPSTARTCFG(0) we can go ahead and do DEPXFERCFG for every hardware endpoint as well. We are guaranteed that there are as many transfer resources as endpoints. This patch triggers off of the calling dwc3_gadget_start_config() for EP0-out, which always happens first, and which should only happen in one of the above conditions. Fixes: aebda6187181 ("usb: dwc3: Reset the transfer resource index on SET_INTERFACE") Reported-by: Ravi Babu <ravibabu@ti.com> Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <balbi@kernel.org> [bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> 
commit c450960187f45d4260db87c7dd4fc0bceb5565d8 upstream.

The assignement of EP transfer resources was not handled properly in the
dwc3 driver. Commit aebda6187181 ("usb: dwc3: Reset the transfer
resource index on SET_INTERFACE") previously fixed one aspect of this
where resources may be exhausted with multiple calls to SET_INTERFACE.
However, it introduced an issue where composite devices with multiple
interfaces can be assigned the same transfer resources for different
endpoints. This patch solves both issues.

The assignment of transfer resources cannot perfectly follow the data
book due to the fact that the controller driver does not have all
knowledge of the configuration in advance. It is given this information
piecemeal by the composite gadget framework after every
SET_CONFIGURATION and SET_INTERFACE. Trying to follow the databook
programming model in this scenario can cause errors. For two reasons:

1) The databook says to do DEPSTARTCFG for every SET_CONFIGURATION and
SET_INTERFACE (8.1.5). This is incorrect in the scenario of multiple
interfaces.

2) The databook does not mention doing more DEPXFERCFG for new endpoint
on alt setting (8.1.6).

The following simplified method is used instead:

All hardware endpoints can be assigned a transfer resource and this
setting will stay persistent until either a core reset or hibernation.
So whenever we do a DEPSTARTCFG(0) we can go ahead and do DEPXFERCFG for
every hardware endpoint as well. We are guaranteed that there are as
many transfer resources as endpoints.

This patch triggers off of the calling dwc3_gadget_start_config() for
EP0-out, which always happens first, and which should only happen in one
of the above conditions.

Fixes: aebda6187181 ("usb: dwc3: Reset the transfer resource index on SET_INTERFACE")
Reported-by: Ravi Babu <ravibabu@ti.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
usb: dwc3: Reset the transfer resource index on SET_INTERFACE 2015-08-12T14:33:22+00:00 John Youn John.Youn@synopsys.com 2001-09-17T07:00:00+00:00 0f0aa7b1634eeed34810f098a8efd80f33486ca4 commit aebda618718157a69c0dc0adb978d69bc2b8723c upstream. This fixes an issue introduced in commit b23c843992b6 (usb: dwc3: gadget: fix DEPSTARTCFG for non-EP0 EPs) that made sure we would only use DEPSTARTCFG once per SetConfig. The trick is that we should use one DEPSTARTCFG per SetConfig *OR* SetInterface. SetInterface was completely missed from the original patch. This problem became aparent after commit 76e838c9f776 (usb: dwc3: gadget: return error if command sent to DEPCMD register fails) added checking of the return status of device endpoint commands. 'Set Endpoint Transfer Resource' command was caught failing occasionally. This is because the Transfer Resource Index was not getting reset during a SET_INTERFACE request. Finally, to fix the issue, was we have to do is make sure that our start_config_issued flag gets reset whenever we receive a SetInterface request. To verify the problem (and its fix), all we have to do is run test 9 from testusb with 'testusb -t 9 -s 2048 -a -c 5000'. Tested-by: Huang Rui <ray.huang@amd.com> Tested-by: Subbaraya Sundeep Bhatta <subbaraya.sundeep.bhatta@xilinx.com> Fixes: b23c843992b6 (usb: dwc3: gadget: fix DEPSTARTCFG for non-EP0 EPs) Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <balbi@ti.com> [bwh: Backported to 3.2: use dev_vdbg() instead of dwc3_trace()] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> 
commit aebda618718157a69c0dc0adb978d69bc2b8723c upstream.

This fixes an issue introduced in commit b23c843992b6 (usb: dwc3:
gadget: fix DEPSTARTCFG for non-EP0 EPs) that made sure we would
only use DEPSTARTCFG once per SetConfig.

The trick is that we should use one DEPSTARTCFG per SetConfig *OR*
SetInterface. SetInterface was completely missed from the original
patch.

This problem became aparent after commit 76e838c9f776 (usb: dwc3:
gadget: return error if command sent to DEPCMD register fails)
added checking of the return status of device endpoint commands.

'Set Endpoint Transfer Resource' command was caught failing
occasionally. This is because the Transfer Resource
Index was not getting reset during a SET_INTERFACE request.

Finally, to fix the issue, was we have to do is make sure that
our start_config_issued flag gets reset whenever we receive a
SetInterface request.

To verify the problem (and its fix), all we have to do is run
test 9 from testusb with 'testusb -t 9 -s 2048 -a -c 5000'.

Tested-by: Huang Rui <ray.huang@amd.com>
Tested-by: Subbaraya Sundeep Bhatta <subbaraya.sundeep.bhatta@xilinx.com>
Fixes: b23c843992b6 (usb: dwc3: gadget: fix DEPSTARTCFG for non-EP0 EPs)
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
[bwh: Backported to 3.2: use dev_vdbg() instead of dwc3_trace()]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
usb: dwc3: gadget: return error if command sent to DEPCMD register fails 2015-08-12T14:33:12+00:00 Subbaraya Sundeep Bhatta subbaraya.sundeep.bhatta@xilinx.com 2015-05-21T10:16:48+00:00 75d7f51f1aebcf9f2f0d6deadb75c612467a2977 commit 76e838c9f7765f9a6205b4d558d75a66104bc60d upstream. We need to return error to caller if command is not sent to controller succesfully. Signed-off-by: Subbaraya Sundeep Bhatta <sbhatta@xilinx.com> Fixes: 72246da40f37 (usb: Introduce DesignWare USB3 DRD Driver) Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk> 
commit 76e838c9f7765f9a6205b4d558d75a66104bc60d upstream.

We need to return error to caller if command is not sent to
controller succesfully.

Signed-off-by: Subbaraya Sundeep Bhatta <sbhatta@xilinx.com>
Fixes: 72246da40f37 (usb: Introduce DesignWare USB3 DRD Driver)
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
usb: dwc3: core: fix order of PM runtime calls 2014-11-05T20:27:41+00:00 Felipe Balbi balbi@ti.com 2014-09-02T19:57:20+00:00 fbe002f7af62511e81f602497343c5a4bb8ab583 commit fed33afce0eda44a46ae24d93aec1b5198c0bac4 upstream. Currently, we disable pm_runtime before all register accesses are done, this is dangerous and might lead to abort exceptions due to the driver trying to access a register which is clocked by a clock which was long gated. Fix that by moving pm_runtime_put_sync() and pm_runtime_disable() as the last thing we do before returning from our ->remove() method. Fixes: 72246da (usb: Introduce DesignWare USB3 DRD Driver) Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk> 
commit fed33afce0eda44a46ae24d93aec1b5198c0bac4 upstream.

Currently, we disable pm_runtime before all register
accesses are done, this is dangerous and might lead
to abort exceptions due to the driver trying to access
a register which is clocked by a clock which was long
gated.

Fix that by moving pm_runtime_put_sync() and pm_runtime_disable()
as the last thing we do before returning from our ->remove()
method.

Fixes: 72246da (usb: Introduce DesignWare USB3 DRD Driver)
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
usb: dwc3: core: use pm_runtime_put_sync() on remove 2014-11-05T20:27:41+00:00 Felipe Balbi balbi@ti.com 2013-10-11T13:34:28+00:00 53de22a51dc90050aa5d83fd75a2bce28bc90f9e commit 16b972a592ea2c9a3c2a3c12238de650fd4043a9 upstream. We are going to disable runtime_pm and we're removing the driver, we must disable the device now. Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk> 
commit 16b972a592ea2c9a3c2a3c12238de650fd4043a9 upstream.

We are going to disable runtime_pm and we're
removing the driver, we must disable the device
now.

Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
usb: dwc3: fix wrong bit mask in dwc3_event_devt 2014-04-30T15:23:20+00:00 Huang Rui ray.huang@amd.com 2014-01-07T09:45:50+00:00 8359dbebb14ceeac2ad73b47869c68a0a0603c9a commit 06f9b6e59661cee510b04513b13ea7927727d758 upstream. Around DWC USB3 2.30a release another bit has been added to the Device-Specific Event (DEVT) Event Information (EvtInfo) bitfield. Because of that, what used to be 8 bits long, has become 9 bits long. Per dwc3 2.30a+ spec in the Device-Specific Event (DEVT), the field of Event Information Bits(EvtInfo) uses [24:16] bits, and it has 9 bits not 8 bits. And the following reserved field uses [31:25] bits not [31:24] bits, and it has 7 bits. So in dwc3_event_devt, the bit mask should be: event_info [24:16] 9 bits reserved31_25 [31:25] 7 bits This patch makes sure that newer core releases will work fine with Linux and that we will decode the event information properly on new core releases. [ balbi@ti.com : improve commit log a bit ] Signed-off-by: Huang Rui <ray.huang@amd.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk> 
commit 06f9b6e59661cee510b04513b13ea7927727d758 upstream.

Around DWC USB3 2.30a release another bit has been added to the
Device-Specific Event (DEVT) Event Information (EvtInfo) bitfield.

Because of that, what used to be 8 bits long, has become 9 bits long.

Per dwc3 2.30a+ spec in the Device-Specific Event (DEVT), the field of
Event Information Bits(EvtInfo) uses [24:16] bits, and it has 9 bits
not 8 bits. And the following reserved field uses [31:25] bits not
[31:24] bits, and it has 7 bits.

So in dwc3_event_devt, the bit mask should be:
event_info	[24:16]		9 bits
reserved31_25	[31:25]		7 bits

This patch makes sure that newer core releases will work fine with
Linux and that we will decode the event information properly on new
core releases.

[ balbi@ti.com : improve commit log a bit ]

Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
usb: dwc3: fix implementation of endpoint wedge 2014-01-03T04:33:25+00:00 Alan Stern stern@rowland.harvard.edu 2013-11-01T16:05:12+00:00 653106814a7591093b28f23a5d0d207121672781 commit a535d81c92615b8ffb99b7e1fd1fb01effaed1af upstream. The dwc3 UDC driver doesn't implement endpoint wedging correctly. When an endpoint is wedged, the gadget driver should be allowed to clear the wedge by calling usb_ep_clear_halt(). Only the host is prevented from resetting the endpoint. This patch fixes the implementation. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Tested-by: Pratyush Anand <pratyush.anand@st.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk> 
commit a535d81c92615b8ffb99b7e1fd1fb01effaed1af upstream.

The dwc3 UDC driver doesn't implement endpoint wedging correctly.
When an endpoint is wedged, the gadget driver should be allowed to
clear the wedge by calling usb_ep_clear_halt().  Only the host is
prevented from resetting the endpoint.

This patch fixes the implementation.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>