linux-stable.git/drivers/usb/dwc2, branch v6.4

usb: dwc2: platform: add support for utmi optional clock

2023-04-20T08:17:06+00:00

Add support for the utmi clock. It's needed on STM32MP15, when using
the integrated full-speed PHY. This clock is an output of USBPHYC, but
HS USBPHYC is not attached as PHY in this case: Full-Speed PHY is directly
managed in dwc2 glue, through GGPIO register. Typical DT when using FS PHY
&usbotg_hs {
	compatible = "st,stm32mp15-fsotg", "snps,dwc2";
	pinctrl-names = "default";
	pinctrl-0 = <&usbotg_hs_pins_a &usbotg_fs_dp_dm_pins_a>;
	vbus-supply = <&vbus_otg>;
	status = "okay";
};

In this configuration, USBPHYC clock output must be defined, so it can
be properly enabled as a clock provider:
	clocks = <&rcc USBO_K>, <&usbphyc>;
	clock-names = "otg", "utmi";

Acked-by: Minas Harutyunyan 
Signed-off-by: Fabrice Gasnier 
Link: https://lore.kernel.org/r/20230414084137.1050487-4-fabrice.gasnier@foss.st.com
Signed-off-by: Greg Kroah-Hartman

usb: dwc2: improve error handling in __dwc2_lowlevel_hw_enable

2023-04-20T08:17:06+00:00

Add error handling in __dwc2_lowlevel_hw_enable() that may leave the
clocks and regulators enabled upon error.

Acked-by: Minas Harutyunyan 
Signed-off-by: Fabrice Gasnier 
Link: https://lore.kernel.org/r/20230414084137.1050487-2-fabrice.gasnier@foss.st.com
Signed-off-by: Greg Kroah-Hartman

usb: dwc2: Fix spelling mistake "schduler" -> "scheduler"

2023-03-29T07:02:14+00:00

There is a spelling mistakes in dev_warn messages. Fix them.

Signed-off-by: Deming Wang 
Link: https://lore.kernel.org/r/20230325063832.1642-1-wangdeming@inspur.com
Signed-off-by: Greg Kroah-Hartman

Merge 6.3-rc4 into usb-next

2023-03-27T07:27:01+00:00

We need the USB fixes here, and the USB gadget update for future
development patches to be based on.

Signed-off-by: Greg Kroah-Hartman

usb: dwc2: fix a race, don't power off/on phy for dual-role mode

2023-03-23T18:13:16+00:00

When in dual role mode (dr_mode == USB_DR_MODE_OTG), platform probe
successively basically calls:
- dwc2_gadget_init()
- dwc2_hcd_init()
- dwc2_lowlevel_hw_disable() since recent change [1]
- usb_add_gadget_udc()

The PHYs (and so the clocks it may provide) shouldn't be disabled for all
SoCs, in OTG mode, as the HCD part has been initialized.

On STM32 this creates some weird race condition upon boot, when:
- initially attached as a device, to a HOST
- and there is a gadget script invoked to setup the device part.
Below issue becomes systematic, as long as the gadget script isn't
started by userland: the hardware PHYs (and so the clocks provided by the
PHYs) remains disabled.
It ends up in having an endless interrupt storm, before the watchdog
resets the platform.

[   16.924163] dwc2 49000000.usb-otg: EPs: 9, dedicated fifos, 952 entries in SPRAM
[   16.962704] dwc2 49000000.usb-otg: DWC OTG Controller
[   16.966488] dwc2 49000000.usb-otg: new USB bus registered, assigned bus number 2
[   16.974051] dwc2 49000000.usb-otg: irq 77, io mem 0x49000000
[   17.032170] hub 2-0:1.0: USB hub found
[   17.042299] hub 2-0:1.0: 1 port detected
[   17.175408] dwc2 49000000.usb-otg: Mode Mismatch Interrupt: currently in Host mode
[   17.181741] dwc2 49000000.usb-otg: Mode Mismatch Interrupt: currently in Host mode
[   17.189303] dwc2 49000000.usb-otg: Mode Mismatch Interrupt: currently in Host mode
...

The host part is also not functional, until the gadget part is configured.

The HW may only be disabled for peripheral mode (original init), e.g.
dr_mode == USB_DR_MODE_PERIPHERAL, until the gadget driver initializes.

But when in USB_DR_MODE_OTG, the HW should remain enabled, as the HCD part
is able to run, while the gadget part isn't necessarily configured.

I don't fully get the of purpose the original change, that claims disabling
the hardware is missing. It creates conditions on SOCs using the PHY
initialization to be completely non working in OTG mode. Original
change [1] should be reworked to be platform specific.

[1] https://lore.kernel.org/r/20221206-dwc2-gadget-dual-role-v1-2-36515e1092cd@theobroma-systems.com

Fixes: ade23d7b7ec5 ("usb: dwc2: power on/off phy for peripheral mode in dual-role mode")
Cc: stable 
Signed-off-by: Fabrice Gasnier 
Reviewed-by: Quentin Schulz 
Tested-by: Quentin Schulz 
Link: https://lore.kernel.org/r/20230315144433.3095859-1-fabrice.gasnier@foss.st.com
Signed-off-by: Greg Kroah-Hartman

usb: dwc2: fix a devres leak in hw_enable upon suspend resume

2023-03-23T18:12:55+00:00

Each time the platform goes to low power, PM suspend / resume routines
call: __dwc2_lowlevel_hw_enable -> devm_add_action_or_reset().
This adds a new devres each time.
This may also happen at runtime, as dwc2_lowlevel_hw_enable() can be
called from udc_start().

This can be seen with tracing:
- echo 1 > /sys/kernel/debug/tracing/events/dev/devres_log/enable
- go to low power
- cat /sys/kernel/debug/tracing/trace

A new "ADD" entry is found upon each low power cycle:
... devres_log: 49000000.usb-otg ADD 82a13bba devm_action_release (8 bytes)
... devres_log: 49000000.usb-otg ADD 49889daf devm_action_release (8 bytes)
...

A second issue is addressed here:
- regulator_bulk_enable() is called upon each PM cycle (suspend/resume).
- regulator_bulk_disable() never gets called.

So the reference count for these regulators constantly increase, by one
upon each low power cycle, due to missing regulator_bulk_disable() call
in __dwc2_lowlevel_hw_disable().

The original fix that introduced the devm_add_action_or_reset() call,
fixed an issue during probe, that happens due to other errors in
dwc2_driver_probe() -> dwc2_core_reset(). Then the probe fails without
disabling regulators, when dr_mode == USB_DR_MODE_PERIPHERAL.

Rather fix the error path: disable all the low level hardware in the
error path, by using the "hsotg->ll_hw_enabled" flag. Checking dr_mode
has been introduced to avoid a dual call to dwc2_lowlevel_hw_disable().
"ll_hw_enabled" should achieve the same (and is used currently in the
remove() routine).

Fixes: 54c196060510 ("usb: dwc2: Always disable regulators on driver teardown")
Fixes: 33a06f1300a7 ("usb: dwc2: Fix error path in gadget registration")
Cc: stable 
Signed-off-by: Fabrice Gasnier 
Link: https://lore.kernel.org/r/20230316084127.126084-1-fabrice.gasnier@foss.st.com
Signed-off-by: Greg Kroah-Hartman

usb: Use of_property_read_bool() for boolean properties

2023-03-16T11:14:56+00:00

It is preferred to use typed property access functions (i.e.
of_property_read_ functions) rather than low-level
of_get_property/of_find_property functions for reading properties.
Convert reading boolean properties to to of_property_read_bool().

Signed-off-by: Rob Herring 
Reviewed-by: Richard Leitner 
Link: https://lore.kernel.org/r/20230310144729.1545857-1-robh@kernel.org
Signed-off-by: Greg Kroah-Hartman

usb: dwc2: drd: fix inconsistent mode if role-switch-default-mode="host"

2023-03-09T14:38:24+00:00

Some boards might use USB-A female connector for USB ports, however,
the port could be connected to a dual-mode USB controller, making it
also behaves as a peripheral device if male-to-male cable is connected.

In this case, the dts looks like this:

	&usb0 {
		status = "okay";
		dr_mode = "otg";
		usb-role-switch;
		role-switch-default-mode = "host";
	};

After boot, dwc2_ovr_init() sets GOTGCTL to GOTGCTL_AVALOVAL and call
dwc2_force_mode() with parameter host=false, which causes inconsistent
mode - The hardware is in peripheral mode while the kernel status is
in host mode.

What we can do now is to call dwc2_drd_role_sw_set() to switch to
device mode, and everything should work just fine now, even switching
back to none(default) mode afterwards.

Fixes: e14acb876985 ("usb: dwc2: drd: add role-switch-default-node support")
Cc: stable 
Signed-off-by: Ziyang Huang 
Tested-by: Fabrice Gasnier 
Acked-by: Minas Harutyunyan 
Reviewed-by: Amelie Delaunay 
Link: https://lore.kernel.org/r/SG2PR01MB204837BF68EDB0E343D2A375C9A59@SG2PR01MB2048.apcprd01.prod.exchangelabs.com
Signed-off-by: Greg Kroah-Hartman

usb: dwc2: power on/off phy for peripheral mode in dual-role mode

2022-12-08T15:50:56+00:00

The PHY power is handled for peripheral mode but only when the device is
forced into this peripheral mode. It is missing when the device is
operating in peripheral mode when dual-role mode is enabled, so let's
update the condition to match this scenario.

Signed-off-by: Quentin Schulz 
Link: https://lore.kernel.org/r/20221206-dwc2-gadget-dual-role-v1-2-36515e1092cd@theobroma-systems.com
Signed-off-by: Greg Kroah-Hartman

usb: dwc2: disable lpm feature on Rockchip SoCs

2022-12-08T15:50:56+00:00

LPM feature of DWC2 module integrated in Rockchip SoCs doesn't work
properly or needs some additional handling, so disable it for now.
Without disabling LPM feature, the USB ADB communication fail with
the following error log:

dwc2 ff580000.usb: new address 27
dwc2 ff580000.usb: Failed to exit L1 sleep state in 200us.
dwc2 ff580000.usb: dwc2_hsotg_send_reply: cannot queue req
dwc2 ff580000.usb: dwc2_hsotg_process_req_status: failed to send reply
dwc2 ff580000.usb: dwc2_hsotg_enqueue_setup: failed queue (-11)
dwc2 ff580000.usb: Failed to exit L1 sleep state in 200us.

[diff vs vendor kernel: added lpm_clock_gating, besl and
 hird_threshold_en settings as seen in  commit 53febc956900 ("usb: dwc2:
 disable Link Power Management on STM32MP15 HS OTG")]

Signed-off-by: William Wu 
Signed-off-by: Frank Wang 
Signed-off-by: Quentin Schulz 
Link: https://lore.kernel.org/r/20221206-dwc2-gadget-dual-role-v1-1-36515e1092cd@theobroma-systems.com
Signed-off-by: Greg Kroah-Hartman