linux-stable.git/drivers/usb/core, branch v6.6.86 Linux kernel stable tree usb: quirks: Add DELAY_INIT and NO_LPM for Prolific Mass Storage Card Reader 2025-03-13T11:58:33+00:00 Miao Li limiao@kylinos.cn 2025-03-04T07:07:57+00:00 7f0441af6ca5d87815ccb40bf3e8c82f8b45c29a commit ff712188daa3fe3ce7e11e530b4dca3826dae14a upstream. When used on Huawei hisi platforms, Prolific Mass Storage Card Reader which the VID:PID is in 067b:2731 might fail to enumerate at boot time and doesn't work well with LPM enabled, combination quirks: USB_QUIRK_DELAY_INIT + USB_QUIRK_NO_LPM fixed the problems. Signed-off-by: Miao Li <limiao@kylinos.cn> Cc: stable <stable@kernel.org> Link: https://lore.kernel.org/r/20250304070757.139473-1-limiao870622@163.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit ff712188daa3fe3ce7e11e530b4dca3826dae14a upstream.

When used on Huawei hisi platforms, Prolific Mass Storage Card Reader
which the VID:PID is in 067b:2731 might fail to enumerate at boot time
and doesn't work well with LPM enabled, combination quirks:
	USB_QUIRK_DELAY_INIT + USB_QUIRK_NO_LPM
fixed the problems.

Signed-off-by: Miao Li <limiao@kylinos.cn>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20250304070757.139473-1-limiao870622@163.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb: hub: lack of clearing xHC resources 2025-03-13T11:58:33+00:00 Pawel Laszczak pawell@cadence.com 2025-02-28T07:50:25+00:00 7817af8b0b8e6f97229a5caf42b7ffd4af681a03 commit 2b66ef84d0d2a0ea955b40bd306f5e3abbc5cf9c upstream. The xHC resources allocated for USB devices are not released in correct order after resuming in case when while suspend device was reconnected. This issue has been detected during the fallowing scenario: - connect hub HS to root port - connect LS/FS device to hub port - wait for enumeration to finish - force host to suspend - reconnect hub attached to root port - wake host For this scenario during enumeration of USB LS/FS device the Cadence xHC reports completion error code for xHC commands because the xHC resources used for devices has not been properly released. XHCI specification doesn't mention that device can be reset in any order so, we should not treat this issue as Cadence xHC controller bug. Similar as during disconnecting in this case the device resources should be cleared starting form the last usb device in tree toward the root hub. To fix this issue usbcore driver should call hcd->driver->reset_device for all USB devices connected to hub which was reconnected while suspending. Fixes: 3d82904559f4 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver") Cc: stable <stable@kernel.org> Signed-off-by: Pawel Laszczak <pawell@cadence.com> Reviewed-by: Alan Stern <stern@rowland.harvard.edu> Link: https://lore.kernel.org/r/PH7PR07MB953841E38C088678ACDCF6EEDDCC2@PH7PR07MB9538.namprd07.prod.outlook.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 2b66ef84d0d2a0ea955b40bd306f5e3abbc5cf9c upstream.

The xHC resources allocated for USB devices are not released in correct
order after resuming in case when while suspend device was reconnected.

This issue has been detected during the fallowing scenario:
- connect hub HS to root port
- connect LS/FS device to hub port
- wait for enumeration to finish
- force host to suspend
- reconnect hub attached to root port
- wake host

For this scenario during enumeration of USB LS/FS device the Cadence xHC
reports completion error code for xHC commands because the xHC resources
used for devices has not been properly released.
XHCI specification doesn't mention that device can be reset in any order
so, we should not treat this issue as Cadence xHC controller bug.
Similar as during disconnecting in this case the device resources should
be cleared starting form the last usb device in tree toward the root hub.
To fix this issue usbcore driver should call hcd->driver->reset_device
for all USB devices connected to hub which was reconnected while
suspending.

Fixes: 3d82904559f4 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/PH7PR07MB953841E38C088678ACDCF6EEDDCC2@PH7PR07MB9538.namprd07.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB: hub: Ignore non-compliant devices with too many configs or interfaces 2025-02-21T12:57:15+00:00 Alan Stern stern@rowland.harvard.edu 2025-01-22T19:26:17+00:00 e905a0fca7bff0855d312c16f71e60e1773b393e commit 2240fed37afbcdb5e8b627bc7ad986891100e05d upstream. Robert Morris created a test program which can cause usb_hub_to_struct_hub() to dereference a NULL or inappropriate pointer: Oops: general protection fault, probably for non-canonical address 0xcccccccccccccccc: 0000 [#1] SMP DEBUG_PAGEALLOC PTI CPU: 7 UID: 0 PID: 117 Comm: kworker/7:1 Not tainted 6.13.0-rc3-00017-gf44d154d6e3d #14 Hardware name: FreeBSD BHYVE/BHYVE, BIOS 14.0 10/17/2021 Workqueue: usb_hub_wq hub_event RIP: 0010:usb_hub_adjust_deviceremovable+0x78/0x110 ... Call Trace: <TASK> ? die_addr+0x31/0x80 ? exc_general_protection+0x1b4/0x3c0 ? asm_exc_general_protection+0x26/0x30 ? usb_hub_adjust_deviceremovable+0x78/0x110 hub_probe+0x7c7/0xab0 usb_probe_interface+0x14b/0x350 really_probe+0xd0/0x2d0 ? __pfx___device_attach_driver+0x10/0x10 __driver_probe_device+0x6e/0x110 driver_probe_device+0x1a/0x90 __device_attach_driver+0x7e/0xc0 bus_for_each_drv+0x7f/0xd0 __device_attach+0xaa/0x1a0 bus_probe_device+0x8b/0xa0 device_add+0x62e/0x810 usb_set_configuration+0x65d/0x990 usb_generic_driver_probe+0x4b/0x70 usb_probe_device+0x36/0xd0 The cause of this error is that the device has two interfaces, and the hub driver binds to interface 1 instead of interface 0, which is where usb_hub_to_struct_hub() looks. We can prevent the problem from occurring by refusing to accept hub devices that violate the USB spec by having more than one configuration or interface. Reported-and-tested-by: Robert Morris <rtm@csail.mit.edu> Cc: stable <stable@kernel.org> Closes: https://lore.kernel.org/linux-usb/95564.1737394039@localhost/ Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Link: https://lore.kernel.org/r/c27f3bf4-63d8-4fb5-ac82-09e3cd19f61c@rowland.harvard.edu Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 2240fed37afbcdb5e8b627bc7ad986891100e05d upstream.

Robert Morris created a test program which can cause
usb_hub_to_struct_hub() to dereference a NULL or inappropriate
pointer:

Oops: general protection fault, probably for non-canonical address
0xcccccccccccccccc: 0000 [#1] SMP DEBUG_PAGEALLOC PTI
CPU: 7 UID: 0 PID: 117 Comm: kworker/7:1 Not tainted 6.13.0-rc3-00017-gf44d154d6e3d #14
Hardware name: FreeBSD BHYVE/BHYVE, BIOS 14.0 10/17/2021
Workqueue: usb_hub_wq hub_event
RIP: 0010:usb_hub_adjust_deviceremovable+0x78/0x110
...
Call Trace:
 <TASK>
 ? die_addr+0x31/0x80
 ? exc_general_protection+0x1b4/0x3c0
 ? asm_exc_general_protection+0x26/0x30
 ? usb_hub_adjust_deviceremovable+0x78/0x110
 hub_probe+0x7c7/0xab0
 usb_probe_interface+0x14b/0x350
 really_probe+0xd0/0x2d0
 ? __pfx___device_attach_driver+0x10/0x10
 __driver_probe_device+0x6e/0x110
 driver_probe_device+0x1a/0x90
 __device_attach_driver+0x7e/0xc0
 bus_for_each_drv+0x7f/0xd0
 __device_attach+0xaa/0x1a0
 bus_probe_device+0x8b/0xa0
 device_add+0x62e/0x810
 usb_set_configuration+0x65d/0x990
 usb_generic_driver_probe+0x4b/0x70
 usb_probe_device+0x36/0xd0

The cause of this error is that the device has two interfaces, and the
hub driver binds to interface 1 instead of interface 0, which is where
usb_hub_to_struct_hub() looks.

We can prevent the problem from occurring by refusing to accept hub
devices that violate the USB spec by having more than one
configuration or interface.

Reported-and-tested-by: Robert Morris <rtm@csail.mit.edu>
Cc: stable <stable@kernel.org>
Closes: https://lore.kernel.org/linux-usb/95564.1737394039@localhost/
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/c27f3bf4-63d8-4fb5-ac82-09e3cd19f61c@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB: Add USB_QUIRK_NO_LPM quirk for sony xperia xz1 smartphone 2025-02-21T12:57:15+00:00 Mathias Nyman mathias.nyman@linux.intel.com 2025-02-06T15:18:36+00:00 8b6efb4d389e5d73f6f3d6641ec9fc1c231491d7 commit 159daf1258227f44b26b5d38f4aa8f37b8cca663 upstream. The fastboot tool for communicating with Android bootloaders does not work reliably with this device if USB 2 Link Power Management (LPM) is enabled. Various fastboot commands are affected, including the following, which usually reproduces the problem within two tries: fastboot getvar kernel getvar:kernel FAILED (remote: 'GetVar Variable Not found') This issue was hidden on many systems up until commit 63a1f8454962 ("xhci: stored cached port capability values in one place") as the xhci driver failed to detect USB 2 LPM support if USB 3 ports were listed before USB 2 ports in the "supported protocol capabilities". Adding the quirk resolves the issue. No drawbacks are expected since the device uses different USB product IDs outside of fastboot mode, and since fastboot commands worked before, until LPM was enabled on the tested system by the aforementioned commit. Based on a patch from Forest <forestix@nom.one> from which most of the code and commit message is taken. Cc: stable <stable@kernel.org> Reported-by: Forest <forestix@nom.one> Closes: https://lore.kernel.org/hk8umj9lv4l4qguftdq1luqtdrpa1gks5l@sonic.net Tested-by: Forest <forestix@nom.one> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/20250206151836.51742-1-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 159daf1258227f44b26b5d38f4aa8f37b8cca663 upstream.

The fastboot tool for communicating with Android bootloaders does not
work reliably with this device if USB 2 Link Power Management (LPM)
is enabled.

Various fastboot commands are affected, including the
following, which usually reproduces the problem within two tries:

  fastboot getvar kernel
  getvar:kernel  FAILED (remote: 'GetVar Variable Not found')

This issue was hidden on many systems up until commit 63a1f8454962
("xhci: stored cached port capability values in one place") as the xhci
driver failed to detect USB 2 LPM support if USB 3 ports were listed
before USB 2 ports in the "supported protocol capabilities".

Adding the quirk resolves the issue. No drawbacks are expected since
the device uses different USB product IDs outside of fastboot mode, and
since fastboot commands worked before, until LPM was enabled on the
tested system by the aforementioned commit.

Based on a patch from Forest <forestix@nom.one> from which most of the
code and commit message is taken.

Cc: stable <stable@kernel.org>
Reported-by: Forest <forestix@nom.one>
Closes: https://lore.kernel.org/hk8umj9lv4l4qguftdq1luqtdrpa1gks5l@sonic.net
Tested-by: Forest <forestix@nom.one>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250206151836.51742-1-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB: quirks: add USB_QUIRK_NO_LPM quirk for Teclast dist 2025-02-21T12:57:14+00:00 Lei Huang huanglei@kylinos.cn 2025-02-12T09:38:29+00:00 483cfd0f58fdbd6f4f589b84731cb2b3f8399aff commit e169d96eecd447ff7fd7542ca5fa0911f5622054 upstream. Teclast disk used on Huawei hisi platforms doesn't work well, losing connectivity intermittently if LPM is enabled. Add quirk disable LPM to resolve the issue. Signed-off-by: Lei Huang <huanglei@kylinos.cn> Cc: stable <stable@kernel.org> Link: https://lore.kernel.org/r/20250212093829.7379-1-huanglei814@163.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit e169d96eecd447ff7fd7542ca5fa0911f5622054 upstream.

Teclast disk used on Huawei hisi platforms doesn't work well,
losing connectivity intermittently if LPM is enabled.
Add quirk disable LPM to resolve the issue.

Signed-off-by: Lei Huang <huanglei@kylinos.cn>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20250212093829.7379-1-huanglei814@163.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb: core: fix pipe creation for get_bMaxPacketSize0 2025-02-21T12:57:14+00:00 Stefan Eichenberger stefan.eichenberger@toradex.com 2025-02-03T10:58:24+00:00 54a5e0156ea7529ee8c89488406be882d60cc1d5 commit 4aac0db5a0ebc599d4ad9bf5ebab78afa1f33e10 upstream. When usb_control_msg is used in the get_bMaxPacketSize0 function, the USB pipe does not include the endpoint device number. This can cause failures when a usb hub port is reinitialized after encountering a bad cable connection. As a result, the system logs the following error messages: usb usb2-port1: cannot reset (err = -32) usb usb2-port1: Cannot enable. Maybe the USB cable is bad? usb usb2-port1: attempt power cycle usb 2-1: new high-speed USB device number 5 using ci_hdrc usb 2-1: device descriptor read/8, error -71 The problem began after commit 85d07c556216 ("USB: core: Unite old scheme and new scheme descriptor reads"). There usb_get_device_descriptor was replaced with get_bMaxPacketSize0. Unlike usb_get_device_descriptor, the get_bMaxPacketSize0 function uses the macro usb_rcvaddr0pipe, which does not include the endpoint device number. usb_get_device_descriptor, on the other hand, used the macro usb_rcvctrlpipe, which includes the endpoint device number. By modifying the get_bMaxPacketSize0 function to use usb_rcvctrlpipe instead of usb_rcvaddr0pipe, the issue can be resolved. This change will ensure that the endpoint device number is included in the USB pipe, preventing reinitialization failures. If the endpoint has not set the device number yet, it will still work because the device number is 0 in udev. Cc: stable <stable@kernel.org> Fixes: 85d07c556216 ("USB: core: Unite old scheme and new scheme descriptor reads") Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com> Reviewed-by: Alan Stern <stern@rowland.harvard.edu> Link: https://lore.kernel.org/r/20250203105840.17539-1-eichest@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 4aac0db5a0ebc599d4ad9bf5ebab78afa1f33e10 upstream.

When usb_control_msg is used in the get_bMaxPacketSize0 function, the
USB pipe does not include the endpoint device number. This can cause
failures when a usb hub port is reinitialized after encountering a bad
cable connection. As a result, the system logs the following error
messages:
usb usb2-port1: cannot reset (err = -32)
usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
usb usb2-port1: attempt power cycle
usb 2-1: new high-speed USB device number 5 using ci_hdrc
usb 2-1: device descriptor read/8, error -71

The problem began after commit 85d07c556216 ("USB: core: Unite old
scheme and new scheme descriptor reads"). There
usb_get_device_descriptor was replaced with get_bMaxPacketSize0. Unlike
usb_get_device_descriptor, the get_bMaxPacketSize0 function uses the
macro usb_rcvaddr0pipe, which does not include the endpoint device
number. usb_get_device_descriptor, on the other hand, used the macro
usb_rcvctrlpipe, which includes the endpoint device number.

By modifying the get_bMaxPacketSize0 function to use usb_rcvctrlpipe
instead of usb_rcvaddr0pipe, the issue can be resolved. This change will
ensure that the endpoint device number is included in the USB pipe,
preventing reinitialization failures. If the endpoint has not set the
device number yet, it will still work because the device number is 0 in
udev.

Cc: stable <stable@kernel.org>
Fixes: 85d07c556216 ("USB: core: Unite old scheme and new scheme descriptor reads")
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20250203105840.17539-1-eichest@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb: fix reference leak in usb_new_device() 2025-01-17T12:36:22+00:00 Ma Ke make_ruc2021@163.com 2024-12-18T07:13:46+00:00 953dea074bc5d6e50be39daf04f49a7bb54b8750 commit 0df11fa8cee5a9cf8753d4e2672bb3667138c652 upstream. When device_add(&udev->dev) succeeds and a later call fails, usb_new_device() does not properly call device_del(). As comment of device_add() says, 'if device_add() succeeds, you should call device_del() when you want to get rid of it. If device_add() has not succeeded, use only put_device() to drop the reference count'. Found by code review. Cc: stable <stable@kernel.org> Fixes: 9f8b17e643fe ("USB: make usbdevices export their device nodes instead of using a separate class") Signed-off-by: Ma Ke <make_ruc2021@163.com> Reviewed-by: Alan Stern <stern@rowland.harvard.edu> Link: https://lore.kernel.org/r/20241218071346.2973980-1-make_ruc2021@163.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 0df11fa8cee5a9cf8753d4e2672bb3667138c652 upstream.

When device_add(&udev->dev) succeeds and a later call fails,
usb_new_device() does not properly call device_del(). As comment of
device_add() says, 'if device_add() succeeds, you should call
device_del() when you want to get rid of it. If device_add() has not
succeeded, use only put_device() to drop the reference count'.

Found by code review.

Cc: stable <stable@kernel.org>
Fixes: 9f8b17e643fe ("USB: make usbdevices export their device nodes instead of using a separate class")
Signed-off-by: Ma Ke <make_ruc2021@163.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20241218071346.2973980-1-make_ruc2021@163.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB: core: Disable LPM only for non-suspended ports 2025-01-17T12:36:22+00:00 Kai-Heng Feng kaihengf@nvidia.com 2024-12-06T07:48:17+00:00 730016e0b963e86e5bd15b6c82402c3a32853eeb commit 59bfeaf5454b7e764288d84802577f4a99bf0819 upstream. There's USB error when tegra board is shutting down: [ 180.919315] usb 2-3: Failed to set U1 timeout to 0x0,error code -113 [ 180.919995] usb 2-3: Failed to set U1 timeout to 0xa,error code -113 [ 180.920512] usb 2-3: Failed to set U2 timeout to 0x4,error code -113 [ 186.157172] tegra-xusb 3610000.usb: xHCI host controller not responding, assume dead [ 186.157858] tegra-xusb 3610000.usb: HC died; cleaning up [ 186.317280] tegra-xusb 3610000.usb: Timeout while waiting for evaluate context command The issue is caused by disabling LPM on already suspended ports. For USB2 LPM, the LPM is already disabled during port suspend. For USB3 LPM, port won't transit to U1/U2 when it's already suspended in U3, hence disabling LPM is only needed for ports that are not suspended. Cc: Wayne Chang <waynec@nvidia.com> Cc: stable <stable@kernel.org> Fixes: d920a2ed8620 ("usb: Disable USB3 LPM at shutdown") Signed-off-by: Kai-Heng Feng <kaihengf@nvidia.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Tested-by: Jon Hunter <jonathanh@nvidia.com> Link: https://lore.kernel.org/r/20241206074817.89189-1-kaihengf@nvidia.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 59bfeaf5454b7e764288d84802577f4a99bf0819 upstream.

There's USB error when tegra board is shutting down:
[  180.919315] usb 2-3: Failed to set U1 timeout to 0x0,error code -113
[  180.919995] usb 2-3: Failed to set U1 timeout to 0xa,error code -113
[  180.920512] usb 2-3: Failed to set U2 timeout to 0x4,error code -113
[  186.157172] tegra-xusb 3610000.usb: xHCI host controller not responding, assume dead
[  186.157858] tegra-xusb 3610000.usb: HC died; cleaning up
[  186.317280] tegra-xusb 3610000.usb: Timeout while waiting for evaluate context command

The issue is caused by disabling LPM on already suspended ports.

For USB2 LPM, the LPM is already disabled during port suspend. For USB3
LPM, port won't transit to U1/U2 when it's already suspended in U3,
hence disabling LPM is only needed for ports that are not suspended.

Cc: Wayne Chang <waynec@nvidia.com>
Cc: stable <stable@kernel.org>
Fixes: d920a2ed8620 ("usb: Disable USB3 LPM at shutdown")
Signed-off-by: Kai-Heng Feng <kaihengf@nvidia.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20241206074817.89189-1-kaihengf@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb: core: sysfs: Unmerge @usb3_hardware_lpm_attr_group in remove_power_attributes() 2024-09-04T11:28:30+00:00 Zijun Hu quic_zijuhu@quicinc.com 2024-08-20T11:01:27+00:00 8fc7c9dcfe38ed9429fbb5961691c19be06b4d0f commit 3a8839bbb86da7968a792123ed2296d063871a52 upstream. Device attribute group @usb3_hardware_lpm_attr_group is merged by add_power_attributes(), but it is not unmerged explicitly, fixed by unmerging it in remove_power_attributes(). Fixes: 655fe4effe0f ("usbcore: add sysfs support to xHCI usb3 hardware LPM") Cc: stable@vger.kernel.org Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com> Link: https://lore.kernel.org/r/20240820-sysfs_fix-v2-1-a9441487077e@quicinc.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 3a8839bbb86da7968a792123ed2296d063871a52 upstream.

Device attribute group @usb3_hardware_lpm_attr_group is merged by
add_power_attributes(), but it is not unmerged explicitly, fixed by
unmerging it in remove_power_attributes().

Fixes: 655fe4effe0f ("usbcore: add sysfs support to xHCI usb3 hardware LPM")
Cc: stable@vger.kernel.org
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Link: https://lore.kernel.org/r/20240820-sysfs_fix-v2-1-a9441487077e@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB: core: Fix duplicate endpoint bug by clearing reserved bits in the descriptor 2024-07-18T11:21:19+00:00 Alan Stern stern@rowland.harvard.edu 2024-06-27T19:56:18+00:00 647d61aef106dbed9c70447bcddbd4968e67ca64 commit a368ecde8a5055b627749b09c6218ef793043e47 upstream. Syzbot has identified a bug in usbcore (see the Closes: tag below) caused by our assumption that the reserved bits in an endpoint descriptor's bEndpointAddress field will always be 0. As a result of the bug, the endpoint_is_duplicate() routine in config.c (and possibly other routines as well) may believe that two descriptors are for distinct endpoints, even though they have the same direction and endpoint number. This can lead to confusion, including the bug identified by syzbot (two descriptors with matching endpoint numbers and directions, where one was interrupt and the other was bulk). To fix the bug, we will clear the reserved bits in bEndpointAddress when we parse the descriptor. (Note that both the USB-2.0 and USB-3.1 specs say these bits are "Reserved, reset to zero".) This requires us to make a copy of the descriptor earlier in usb_parse_endpoint() and use the copy instead of the original when checking for duplicates. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-and-tested-by: syzbot+8693a0bb9c10b554272a@syzkaller.appspotmail.com Closes: https://lore.kernel.org/linux-usb/0000000000003d868e061bc0f554@google.com/ Fixes: 0a8fd1346254 ("USB: fix problems with duplicate endpoint addresses") CC: Oliver Neukum <oneukum@suse.com> CC: stable@vger.kernel.org Link: https://lore.kernel.org/r/205a5edc-7fef-4159-b64a-80374b6b101a@rowland.harvard.edu Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit a368ecde8a5055b627749b09c6218ef793043e47 upstream.

Syzbot has identified a bug in usbcore (see the Closes: tag below)
caused by our assumption that the reserved bits in an endpoint
descriptor's bEndpointAddress field will always be 0.  As a result of
the bug, the endpoint_is_duplicate() routine in config.c (and possibly
other routines as well) may believe that two descriptors are for
distinct endpoints, even though they have the same direction and
endpoint number.  This can lead to confusion, including the bug
identified by syzbot (two descriptors with matching endpoint numbers
and directions, where one was interrupt and the other was bulk).

To fix the bug, we will clear the reserved bits in bEndpointAddress
when we parse the descriptor.  (Note that both the USB-2.0 and USB-3.1
specs say these bits are "Reserved, reset to zero".)  This requires us
to make a copy of the descriptor earlier in usb_parse_endpoint() and
use the copy instead of the original when checking for duplicates.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: syzbot+8693a0bb9c10b554272a@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/linux-usb/0000000000003d868e061bc0f554@google.com/
Fixes: 0a8fd1346254 ("USB: fix problems with duplicate endpoint addresses")
CC: Oliver Neukum <oneukum@suse.com>
CC: stable@vger.kernel.org
Link: https://lore.kernel.org/r/205a5edc-7fef-4159-b64a-80374b6b101a@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>