linux-stable.git/drivers/usb/core, branch v4.4.64

usb: hub: Wait for connection to be reestablished after port reset

2017-04-18T05:14:37+00:00

commit 22547c4cc4fe20698a6a85a55b8788859134b8e4 upstream.

On a system with a defective USB device connected to an USB hub,
an endless sequence of port connect events was observed. The sequence
of events as observed is as follows:

- Port reports connected event (port status=USB_PORT_STAT_CONNECTION).
- Event handler debounces port and resets it by calling hub_port_reset().
- hub_port_reset() calls hub_port_wait_reset() to wait for the reset
  to complete.
- The reset completes, but USB_PORT_STAT_CONNECTION is not immediately
  set in the port status register.
- hub_port_wait_reset() returns -ENOTCONN.
- Port initialization sequence is aborted.
- A few milliseconds later, the port again reports a connected event,
  and the sequence repeats.

This continues either forever or, randomly, stops if the connection
is already re-established when the port status is read. It results in
a high rate of udev events. This in turn destabilizes userspace since
the above sequence holds the device mutex pretty much continuously
and prevents userspace from actually reading the device status.

To prevent the problem from happening, let's wait for the connection
to be re-established after a port reset. If the device was actually
disconnected, the code will still return an error, but it will do so
only after the long reset timeout.

Cc: Douglas Anderson 
Signed-off-by: Guenter Roeck 
Acked-by: Alan Stern 
Signed-off-by: Sumit Semwal 
Signed-off-by: Greg Kroah-Hartman

USB: fix linked-list corruption in rh_call_control()

2017-04-08T07:53:31+00:00

commit 1633682053a7ee8058e10c76722b9b28e97fb73f upstream.

Using KASAN, Dmitry found a bug in the rh_call_control() routine: If
buffer allocation fails, the routine returns immediately without
unlinking its URB from the control endpoint, eventually leading to
linked-list corruption.

This patch fixes the problem by jumping to the end of the routine
(where the URB is unlinked) when an allocation failure occurs.

Signed-off-by: Alan Stern 
Reported-and-tested-by: Dmitry Vyukov 
Signed-off-by: Greg Kroah-Hartman

usb: hub: Fix crash after failure to read BOS descriptor

2017-03-30T07:35:17+00:00

commit 7b2db29fbb4e766fcd02207eb2e2087170bd6ebc upstream.

If usb_get_bos_descriptor() returns an error, usb->bos will be NULL.
Nevertheless, it is dereferenced unconditionally in
hub_set_initial_usb2_lpm_policy() if usb2_hw_lpm_capable is set.
This results in a crash.

usb 5-1: unable to get BOS descriptor
...
Unable to handle kernel NULL pointer dereference at virtual address 00000008
pgd = ffffffc00165f000
[00000008] *pgd=000000000174f003, *pud=000000000174f003,
		*pmd=0000000001750003, *pte=00e8000001751713
Internal error: Oops: 96000005 [#1] PREEMPT SMP
Modules linked in: uinput uvcvideo videobuf2_vmalloc cmac [ ... ]
CPU: 5 PID: 3353 Comm: kworker/5:3 Tainted: G    B 4.4.52 #480
Hardware name: Google Kevin (DT)
Workqueue: events driver_set_config_work
task: ffffffc0c3690000 ti: ffffffc0ae9a8000 task.ti: ffffffc0ae9a8000
PC is at hub_port_init+0xc3c/0xd10
LR is at hub_port_init+0xc3c/0xd10
...
Call trace:
[] hub_port_init+0xc3c/0xd10
[] usb_reset_and_verify_device+0x15c/0x82c
[] usb_reset_device+0xe4/0x298
[] rtl8152_probe+0x84/0x9b0 [r8152]
[] usb_probe_interface+0x244/0x2f8
[] driver_probe_device+0x180/0x3b4
[] __device_attach_driver+0xb4/0xe0
[] bus_for_each_drv+0xb4/0xe4
[] __device_attach+0xd0/0x158
[] device_initial_probe+0x24/0x30
[] bus_probe_device+0x50/0xe4
[] device_add+0x414/0x738
[] usb_set_configuration+0x89c/0x914
[] driver_set_config_work+0xc0/0xf0
[] process_one_work+0x390/0x6b8
[] worker_thread+0x480/0x610
[] kthread+0x164/0x178
[] ret_from_fork+0x10/0x40

Since we don't know anything about LPM capabilities without BOS descriptor,
don't attempt to enable LPM if it is not available.

Fixes: 890dae886721 ("xhci: Enable LPM support only for hardwired ...")
Cc: Mathias Nyman 
Signed-off-by: Guenter Roeck 
Acked-by: Mathias Nyman 
Signed-off-by: Greg Kroah-Hartman

usb-core: Add LINEAR_FRAME_INTR_BINTERVAL USB quirk

2017-03-30T07:35:16+00:00

commit 3243367b209faed5c320a4e5f9a565ee2a2ba958 upstream.

Some USB 2.0 devices erroneously report millisecond values in
bInterval. The generic config code manages to catch most of them,
but in some cases it's not completely enough.

The case at stake here is a USB 2.0 braille device, which wants to
announce 10ms and thus sets bInterval to 10, but with the USB 2.0
computation that yields to 64ms.  It happens that one can type fast
enough to reach this interval and get the device buffers overflown,
leading to problematic latencies.  The generic config code does not
catch this case because the 64ms is considered a sane enough value.

This change thus adds a USB_QUIRK_LINEAR_FRAME_INTR_BINTERVAL quirk
to mark devices which actually report milliseconds in bInterval,
and marks Vario Ultra devices as needing it.

Signed-off-by: Samuel Thibault 
Acked-by: Alan Stern 
Signed-off-by: Greg Kroah-Hartman

USB: don't free bandwidth_mutex too early

2017-03-26T10:13:17+00:00

commit ab2a4bf83902c170d29ba130a8abb5f9d90559e1 upstream.

The USB core contains a bug that can show up when a USB-3 host
controller is removed.  If the primary (USB-2) hcd structure is
released before the shared (USB-3) hcd, the core will try to do a
double-free of the common bandwidth_mutex.

The problem was described in graphical form by Chung-Geol Kim, who
first reported it:

=================================================
     At *remove USB(3.0) Storage
     sequence <1> --> <5> ((Problem Case))
=================================================
                                  VOLD
------------------------------------|------------
                                 (uevent)
                            ________|_________
                           |<1>               |
                           |dwc3_otg_sm_work  |
                           |usb_put_hcd       |
                           |peer_hcd(kref=2)|
                           |__________________|
                            ________|_________
                           |<2>               |
                           |New USB BUS #2    |
                           |                  |
                           |peer_hcd(kref=1)  |
                           |                  |
                         --(Link)-bandXX_mutex|
                         | |__________________|
                         |
    ___________________  |
   |<3>                | |
   |dwc3_otg_sm_work   | |
   |usb_put_hcd        | |
   |primary_hcd(kref=1)| |
   |___________________| |
    _________|_________  |
   |<4>                | |
   |New USB BUS #1     | |
   |hcd_release        | |
   |primary_hcd(kref=0)| |
   |                   | |
   |bandXX_mutex(free) |<-
   |___________________|
                               (( VOLD ))
                            ______|___________
                           |<5>               |
                           |      SCSI        |
                           |usb_put_hcd       |
                           |peer_hcd(kref=0)  |
                           |*hcd_release      |
                           |bandXX_mutex(free*)|<- double free
                           |__________________|

=================================================

This happens because hcd_release() frees the bandwidth_mutex whenever
it sees a primary hcd being released (which is not a very good idea
in any case), but in the course of releasing the primary hcd, it
changes the pointers in the shared hcd in such a way that the shared
hcd will appear to be primary when it gets released.

This patch fixes the problem by changing hcd_release() so that it
deallocates the bandwidth_mutex only when the _last_ hcd structure
referencing it is released.  The patch also removes an unnecessary
test, so that when an hcd is released, both the shared_hcd and
primary_hcd pointers in the hcd's peer will be cleared.

Signed-off-by: Alan Stern 
Reported-by: Chung-Geol Kim 
Tested-by: Chung-Geol Kim 
Cc: Sumit Semwal 
Signed-off-by: Greg Kroah-Hartman

usb: core: hub: hub_port_init lock controller instead of bus

2017-03-26T10:13:16+00:00

commit feb26ac31a2a5cb88d86680d9a94916a6343e9e6 upstream.

The XHCI controller presents two USB buses to the system - one for USB2
and one for USB3. The hub init code (hub_port_init) is reentrant but
only locks one bus per thread, leading to a race condition failure when
two threads attempt to simultaneously initialise a USB2 and USB3 device:

[    8.034843] xhci_hcd 0000:00:14.0: Timeout while waiting for setup device command
[   13.183701] usb 3-3: device descriptor read/all, error -110

On a test system this failure occurred on 6% of all boots.

The call traces at the point of failure are:

Call Trace:
 [] schedule+0x37/0x90
 [] usb_kill_urb+0x8d/0xd0
 [] ? wake_up_atomic_t+0x30/0x30
 [] usb_start_wait_urb+0xbe/0x150
 [] usb_control_msg+0xbc/0xf0
 [] hub_port_init+0x51e/0xb70
 [] hub_event+0x817/0x1570
 [] process_one_work+0x1ff/0x620
 [] ? process_one_work+0x15f/0x620
 [] worker_thread+0x64/0x4b0
 [] ? rescuer_thread+0x390/0x390
 [] kthread+0x105/0x120
 [] ? kthread_create_on_node+0x200/0x200
 [] ret_from_fork+0x3f/0x70
 [] ? kthread_create_on_node+0x200/0x200

Call Trace:
 [] xhci_setup_device+0x53d/0xa40
 [] xhci_address_device+0xe/0x10
 [] hub_port_init+0x1bf/0xb70
 [] ? trace_hardirqs_on+0xd/0x10
 [] hub_event+0x817/0x1570
 [] process_one_work+0x1ff/0x620
 [] ? process_one_work+0x15f/0x620
 [] worker_thread+0x64/0x4b0
 [] ? rescuer_thread+0x390/0x390
 [] kthread+0x105/0x120
 [] ? kthread_create_on_node+0x200/0x200
 [] ret_from_fork+0x3f/0x70
 [] ? kthread_create_on_node+0x200/0x200

Which results from the two call chains:

hub_port_init
 usb_get_device_descriptor
  usb_get_descriptor
   usb_control_msg
    usb_internal_control_msg
     usb_start_wait_urb
      usb_submit_urb / wait_for_completion_timeout / usb_kill_urb

hub_port_init
 hub_set_address
  xhci_address_device
   xhci_setup_device

Mathias Nyman explains the current behaviour violates the XHCI spec:

 hub_port_reset() will end up moving the corresponding xhci device slot
 to default state.

 As hub_port_reset() is called several times in hub_port_init() it
 sounds reasonable that we could end up with two threads having their
 xhci device slots in default state at the same time, which according to
 xhci 4.5.3 specs still is a big no no:

 "Note: Software shall not transition more than one Device Slot to the
  Default State at a time"

 So both threads fail at their next task after this.
 One fails to read the descriptor, and the other fails addressing the
 device.

Fix this in hub_port_init by locking the USB controller (instead of an
individual bus) to prevent simultaneous initialisation of both buses.

Fixes: 638139eb95d2 ("usb: hub: allow to process more usb hub events in parallel")
Link: https://lkml.org/lkml/2016/2/8/312
Link: https://lkml.org/lkml/2016/2/4/748
Signed-off-by: Chris Bainbridge 
Cc: stable 
Acked-by: Mathias Nyman 
Signed-off-by: Sumit Semwal 
 [sumits: minor merge conflict resolution for linux-4.4.y]
Signed-off-by: Greg Kroah-Hartman

USB: Add quirk for WORLDE easykey.25 MIDI keyboard

2017-02-09T07:02:46+00:00

commit d9b2997e4a0a874e452df7cdd7de5a54502bd0aa upstream.

Add a quirk for WORLDE easykey.25 MIDI keyboard (idVendor=0218,
idProduct=0401). The device reports that it has config string
descriptor at index 3, but when the system selects the configuration
and tries to get the description, it returns a -EPROTO error,
the communication restarts and this keeps repeating over and over again.
Not requesting the string descriptor makes the device work correctly.

Relevant info from Wireshark:

[...]

CONFIGURATION DESCRIPTOR
    bLength: 9
    bDescriptorType: 0x02 (CONFIGURATION)
    wTotalLength: 101
    bNumInterfaces: 2
    bConfigurationValue: 1
    iConfiguration: 3
    Configuration bmAttributes: 0xc0  SELF-POWERED  NO REMOTE-WAKEUP
        1... .... = Must be 1: Must be 1 for USB 1.1 and higher
        .1.. .... = Self-Powered: This device is SELF-POWERED
        ..0. .... = Remote Wakeup: This device does NOT support remote wakeup
    bMaxPower: 50  (100mA)

[...]

     45 0.369104       host                  2.38.0                USB      64     GET DESCRIPTOR Request STRING

[...]

URB setup
    bmRequestType: 0x80
        1... .... = Direction: Device-to-host
        .00. .... = Type: Standard (0x00)
        ...0 0000 = Recipient: Device (0x00)
    bRequest: GET DESCRIPTOR (6)
    Descriptor Index: 0x03
    bDescriptorType: 0x03
    Language Id: English (United States) (0x0409)
    wLength: 255

     46 0.369255       2.38.0                host                  USB      64     GET DESCRIPTOR Response STRING[Malformed Packet]

[...]

Frame 46: 64 bytes on wire (512 bits), 64 bytes captured (512 bits) on interface 0
USB URB
    [Source: 2.38.0]
    [Destination: host]
    URB id: 0xffff88021f62d480
    URB type: URB_COMPLETE ('C')
    URB transfer type: URB_CONTROL (0x02)
    Endpoint: 0x80, Direction: IN
    Device: 38
    URB bus id: 2
    Device setup request: not relevant ('-')
    Data: present (0)
    URB sec: 1484896277
    URB usec: 455031
    URB status: Protocol error (-EPROTO) (-71)
    URB length [bytes]: 0
    Data length [bytes]: 0
    [Request in: 45]
    [Time from request: 0.000151000 seconds]
    Unused Setup Header
    Interval: 0
    Start frame: 0
    Copy of Transfer Flags: 0x00000200
    Number of ISO descriptors: 0
[Malformed Packet: USB]
    [Expert Info (Error/Malformed): Malformed Packet (Exception occurred)]
        [Malformed Packet (Exception occurred)]
        [Severity level: Error]
        [Group: Malformed]

Signed-off-by: Lukáš Lalinský 
Signed-off-by: Greg Kroah-Hartman

usb: hub: Move hub_port_disable() to fix warning if PM is disabled

2017-01-12T10:22:47+00:00

commit 3bc02bce908c7250781376052248f5cd60a4e3d4 upstream.

If CONFIG_PM=n:

    drivers/usb/core/hub.c:107: warning: ‘hub_usb3_port_prepare_disable’ declared inline after being called
    drivers/usb/core/hub.c:107: warning: previous declaration of ‘hub_usb3_port_prepare_disable’ was here

To fix this, move hub_port_disable() after
hub_usb3_port_prepare_disable(), and adjust forward declarations.

Fixes: 37be66767e3cae4f ("usb: hub: Fix auto-remount of safely removed or ejected USB-3 devices")
Signed-off-by: Geert Uytterhoeven 
Signed-off-by: Greg Kroah-Hartman

USB: fix problems with duplicate endpoint addresses

2017-01-12T10:22:44+00:00

commit 0a8fd1346254974c3a852338508e4a4cddbb35f1 upstream.

When checking a new device's descriptors, the USB core does not check
for duplicate endpoint addresses.  This can cause a problem when the
sysfs files for those endpoints are created; trying to create multiple
files with the same name will provoke a WARNING:

WARNING: CPU: 2 PID: 865 at fs/sysfs/dir.c:31 sysfs_warn_dup+0x8a/0xa0
sysfs: cannot create duplicate filename
'/devices/platform/dummy_hcd.0/usb2/2-1/2-1:64.0/ep_05'
Kernel panic - not syncing: panic_on_warn set ...

CPU: 2 PID: 865 Comm: kworker/2:1 Not tainted 4.9.0-rc7+ #34
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
Workqueue: usb_hub_wq hub_event
 ffff88006bee64c8 ffffffff81f96b8a ffffffff00000001 1ffff1000d7dcc2c
 ffffed000d7dcc24 0000000000000001 0000000041b58ab3 ffffffff8598b510
 ffffffff81f968f8 ffffffff850fee20 ffffffff85cff020 dffffc0000000000
Call Trace:
 [<     inline     >] __dump_stack lib/dump_stack.c:15
 [] dump_stack+0x292/0x398 lib/dump_stack.c:51
 [] panic+0x1cb/0x3a9 kernel/panic.c:179
 [] __warn+0x1c4/0x1e0 kernel/panic.c:542
 [] warn_slowpath_fmt+0xc5/0x110 kernel/panic.c:565
 [] sysfs_warn_dup+0x8a/0xa0 fs/sysfs/dir.c:30
 [] sysfs_create_dir_ns+0x178/0x1d0 fs/sysfs/dir.c:59
 [<     inline     >] create_dir lib/kobject.c:71
 [] kobject_add_internal+0x227/0xa60 lib/kobject.c:229
 [<     inline     >] kobject_add_varg lib/kobject.c:366
 [] kobject_add+0x139/0x220 lib/kobject.c:411
 [] device_add+0x353/0x1660 drivers/base/core.c:1088
 [] device_register+0x1d/0x20 drivers/base/core.c:1206
 [] usb_create_ep_devs+0x163/0x260 drivers/usb/core/endpoint.c:195
 [] create_intf_ep_devs+0x13b/0x200 drivers/usb/core/message.c:1030
 [] usb_set_configuration+0x1083/0x18d0 drivers/usb/core/message.c:1937
 [] generic_probe+0x6e/0xe0 drivers/usb/core/generic.c:172
 [] usb_probe_device+0xaa/0xe0 drivers/usb/core/driver.c:263

This patch prevents the problem by checking for duplicate endpoint
addresses during enumeration and skipping any duplicates.

Signed-off-by: Alan Stern 
Reported-by: Andrey Konovalov 
Tested-by: Andrey Konovalov 
Signed-off-by: Greg Kroah-Hartman

usb: hub: Fix auto-remount of safely removed or ejected USB-3 devices

2017-01-06T10:16:07+00:00

commit 37be66767e3cae4fd16e064d8bb7f9f72bf5c045 upstream.

USB-3 does not have any link state that will avoid negotiating a connection
with a plugged-in cable but will signal the host when the cable is
unplugged.

For USB-3 we used to first set the link to Disabled, then to RxDdetect to
be able to detect cable connects or disconnects. But in RxDetect the
connected device is detected again and eventually enabled.

Instead set the link into U3 and disable remote wakeups for the device.
This is what Windows does, and what Alan Stern suggested.

Cc: Alan Stern 
Acked-by: Alan Stern 
Signed-off-by: Mathias Nyman 
Signed-off-by: Greg Kroah-Hartman