commit a0fea6027f19c62727315aba1a7fae75a9caa842 upstream.

Without this patch, K70 LUX keyboards don't work, saying
usb 3-3: unable to read config index 0 descriptor/all
usb 3-3: can't read configurations, error -110
usb usb3-port3: unable to enumerate USB device

Signed-off-by: Bernhard Rosenkraenzer <Bernhard.Rosenkranzer@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 2ef47001b3ee3ded579b7532ebdcf8680e4d8c54 upstream.

The USB kerneldoc says that the actual_length field "is read in
non-iso completion functions", but the usbfs driver uses it for all
URB types in processcompl().  Since not all of the host controller
drivers set actual_length for isochronous URBs, programs using usbfs
with some host controllers don't work properly.  For example, Minas
reports that a USB camera controlled by libusb doesn't work properly
with a dwc2 controller.

It doesn't seem worthwhile to change the HCDs and the documentation,
since the in-kernel USB class drivers evidently don't rely on
actual_length for isochronous transfers.  The easiest solution is for
usbfs to calculate the actual_length value for itself, by adding up
the lengths of the individual packets in an isochronous transfer.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Reported-and-tested-by: wlf <wulf@rock-chips.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.

By default all files without license information are under the default
license of the kernel, which is GPL version 2.

Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier.  The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.

This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.

How this work was done:

Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
 - file had no licensing information it it.
 - file was a */uapi/* one with no licensing information in it,
 - file was a */uapi/* one with existing licensing information,

Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.

The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne.  Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.

The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed.  Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.

Criteria used to select files for SPDX license identifier tagging was:
 - Files considered eligible had to be source code files.
 - Make and config files were included as candidates if they contained >5
   lines of source
 - File already had some variant of a license header in it (even if <5
   lines).

All documentation files were explicitly excluded.

The following heuristics were used to determine which SPDX license
identifiers to apply.

 - when both scanners couldn't find any license traces, file was
   considered to have no license information in it, and the top level
   COPYING file license applied.

   For non */uapi/* files that summary was:

   SPDX license identifier                            # files
   ---------------------------------------------------|-------
   GPL-2.0                                              11139

   and resulted in the first patch in this series.

   If that file was a */uapi/* path one, it was "GPL-2.0 WITH
   Linux-syscall-note" otherwise it was "GPL-2.0".  Results of that was:

   SPDX license identifier                            # files
   ---------------------------------------------------|-------
   GPL-2.0 WITH Linux-syscall-note                        930

   and resulted in the second patch in this series.

 - if a file had some form of licensing information in it, and was one
   of the */uapi/* ones, it was denoted with the Linux-syscall-note if
   any GPL family license was found in the file or had no licensing in
   it (per prior point).  Results summary:

   SPDX license identifier                            # files
   ---------------------------------------------------|------
   GPL-2.0 WITH Linux-syscall-note                       270
   GPL-2.0+ WITH Linux-syscall-note                      169
   ((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause)    21
   ((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause)    17
   LGPL-2.1+ WITH Linux-syscall-note                      15
   GPL-1.0+ WITH Linux-syscall-note                       14
   ((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause)    5
   LGPL-2.0+ WITH Linux-syscall-note                       4
   LGPL-2.1 WITH Linux-syscall-note                        3
   ((GPL-2.0 WITH Linux-syscall-note) OR MIT)              3
   ((GPL-2.0 WITH Linux-syscall-note) AND MIT)             1

   and that resulted in the third patch in this series.

 - when the two scanners agreed on the detected license(s), that became
   the concluded license(s).

 - when there was disagreement between the two scanners (one detected a
   license but the other didn't, or they both detected different
   licenses) a manual inspection of the file occurred.

 - In most cases a manual inspection of the information in the file
   resulted in a clear resolution of the license that should apply (and
   which scanner probably needed to revisit its heuristics).

 - When it was not immediately clear, the license identifier was
   confirmed with lawyers working with the Linux Foundation.

 - If there was any question as to the appropriate license identifier,
   the file was flagged for further research and to be revisited later
   in time.

In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.

Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights.  The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.

Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.

In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.

Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
 - a full scancode scan run, collecting the matched texts, detected
   license ids and scores
 - reviewing anything where there was a license detected (about 500+
   files) to ensure that the applied SPDX license was correct
 - reviewing anything where there was no detection but the patch license
   was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
   SPDX license was correct

This produced a worksheet with 20 files needing minor correction.  This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.

These .csv files were then reviewed by Greg.  Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected.  This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.)  Finally Greg ran the script using the .csv files to
generate the patches.

Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

If the connect status change is set during reset signaling, but
the status remains connected just retry port reset.

This solves an issue with connecting a 90W HP Thunderbolt 3 dock
with a Lenovo Carbon x1 (5th generation) which causes a 30min loop
of a high speed device being re-discovererd before usb ports starts
working.

[...]
[ 389.023845] usb 3-1: new high-speed USB device number 55 using xhci_hcd
[ 389.491841] usb 3-1: new high-speed USB device number 56 using xhci_hcd
[ 389.959928] usb 3-1: new high-speed USB device number 57 using xhci_hcd
[...]

This is caused by a high speed device that doesn't successfully go to the
enabled state after the second port reset. Instead the connection bounces
(connected, with connect status change), bailing out completely from
enumeration just to restart from scratch.

Link: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1716332

Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Andrey used the syzkaller fuzzer to find an out-of-bounds memory
access in usb_get_bos_descriptor().  The code wasn't checking that the
next usb_dev_cap_header structure could fit into the remaining buffer
space.

This patch fixes the error and also reduces the bNumDeviceCaps field
in the header to match the actual number of capabilities found, in
cases where there are fewer than expected.

Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This keyboard doesn't implement Get String descriptors properly even
though string indexes are valid. What happens is that when requesting
for the String descriptor, the device disconnects and
reconnects. Without this quirk, this loop will continue forever.

Cc: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Владимир Мартьянов <vilgeforce@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Taking the uurb->buffer_length userspace passes in as a maximum for the
actual urbs transfer_buffer_length causes 2 serious issues:

1) It breaks isochronous support for all userspace apps using libusb,
   as existing libusb versions pass in 0 for uurb->buffer_length,
   relying on the kernel using the lenghts of the usbdevfs_iso_packet_desc
   descriptors passed in added together as buffer length.

   This for example causes redirection of USB audio and Webcam's into
   virtual machines using qemu-kvm to no longer work. This is a userspace
   ABI break and as such must be reverted.

   Note that the original commit does not protect other users / the
   kernels memory, it only stops the userspace process making the call
   from shooting itself in the foot.

2) It may cause the kernel to program host controllers to DMA over random
   memory. Just as the devio code used to only look at the iso_packet_desc
   lenghts, the host drivers do the same, relying on the submitter of the
   urbs to make sure the entire buffer is large enough and not checking
   transfer_buffer_length.

   But the "USB: devio: Don't corrupt user memory" commit now takes the
   userspace provided uurb->buffer_length for the buffer-size while copying
   over the user-provided iso_packet_desc lengths 1:1, allowing the user
   to specify a small buffer size while programming the host controller to
   dma a lot more data.

   (Atleast the ohci, uhci, xhci and fhci drivers do not check
    transfer_buffer_length for isoc transfers.)

This reverts commit fa1ed74eb1c2 ("USB: devio: Don't corrupt user memory")
fixing both these issues.

Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The user buffer has "uurb->buffer_length" bytes.  If the kernel has more
information than that, we should truncate it instead of writing past
the end of the user's buffer.  I added a WARN_ONCE() to help the user
debug the issue.

Reported-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

There used to be an integer overflow check in proc_do_submiturb() but
we removed it.  It turns out that it's still required.  The
uurb->buffer_length variable is a signed integer and it's controlled by
the user.  It can lead to an integer overflow when we do:

	num_sgs = DIV_ROUND_UP(uurb->buffer_length, USB_SG_SIZE);

If we strip away the macro then that line looks like this:

	num_sgs = (uurb->buffer_length + USB_SG_SIZE - 1) / USB_SG_SIZE;
                   ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
It's the first addition which can overflow.

Fixes: 1129d270cbfb ("USB: Increase usbfs transfer limit")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Andrey Konovalov reported a possible out-of-bounds problem for the
cdc_parse_cdc_header function.  He writes:
	It looks like cdc_parse_cdc_header() doesn't validate buflen
	before accessing buffer[1], buffer[2] and so on. The only check
	present is while (buflen > 0).

So fix this issue up by properly validating the buffer length matches
what the descriptor says it is.

Reported-by: Andrey Konovalov <andreyknvl@google.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>