linux-stable.git/drivers/usb/core, branch v4.1.41

usb: hub: Wait for connection to be reestablished after port reset

2017-06-13T13:29:16+00:00

[ Upstream commit 22547c4cc4fe20698a6a85a55b8788859134b8e4 ]

On a system with a defective USB device connected to an USB hub,
an endless sequence of port connect events was observed. The sequence
of events as observed is as follows:

- Port reports connected event (port status=USB_PORT_STAT_CONNECTION).
- Event handler debounces port and resets it by calling hub_port_reset().
- hub_port_reset() calls hub_port_wait_reset() to wait for the reset
  to complete.
- The reset completes, but USB_PORT_STAT_CONNECTION is not immediately
  set in the port status register.
- hub_port_wait_reset() returns -ENOTCONN.
- Port initialization sequence is aborted.
- A few milliseconds later, the port again reports a connected event,
  and the sequence repeats.

This continues either forever or, randomly, stops if the connection
is already re-established when the port status is read. It results in
a high rate of udev events. This in turn destabilizes userspace since
the above sequence holds the device mutex pretty much continuously
and prevents userspace from actually reading the device status.

To prevent the problem from happening, let's wait for the connection
to be re-established after a port reset. If the device was actually
disconnected, the code will still return an error, but it will do so
only after the long reset timeout.

Cc: Douglas Anderson 
Signed-off-by: Guenter Roeck 
Acked-by: Alan Stern 
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Sasha Levin

USB: hub: fix non-SS hub-descriptor handling

2017-06-08T10:12:46+00:00

[ Upstream commit bec444cd1c94c48df409a35ad4e5b143c245c3f7 ]

Add missing sanity check on the non-SuperSpeed hub-descriptor length in
order to avoid parsing and leaking two bytes of uninitialised slab data
through sysfs removable-attributes (or a compound-device debug
statement).

Note that we only make sure that the DeviceRemovable field is always
present (and specifically ignore the unused PortPwrCtrlMask field) in
order to continue support any hubs with non-compliant descriptors. As a
further safeguard, the descriptor buffer is also cleared.

Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Cc: stable      # 2.6.12
Signed-off-by: Johan Hovold 
Acked-by: Alan Stern 
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Sasha Levin

USB: hub: fix SS hub-descriptor handling

2017-06-08T10:12:46+00:00

[ Upstream commit 2c25a2c818023df64463aac3288a9f969491e507 ]

A SuperSpeed hub descriptor does not have any variable-length fields so
bail out when reading a short descriptor.

This avoids parsing and leaking two bytes of uninitialised slab data
through sysfs removable-attributes.

Fixes: dbe79bbe9dcb ("USB 3.0 Hub Changes")
Cc: stable      # 2.6.39
Cc: John Youn 
Acked-by: Alan Stern 
Signed-off-by: Johan Hovold 
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Sasha Levin

USB: core: replace %p with %pK

2017-06-08T10:12:46+00:00

[ Upstream commit 2f964780c03b73de269b08d12aff96a9618d13f3 ]

Format specifier %p can leak kernel addresses while not valuing the
kptr_restrict system settings. When kptr_restrict is set to (1), kernel
pointers printed using the %pK format specifier will be replaced with
Zeros. Debugging Note : &pK prints only Zeros as address. If you need
actual address information, write 0 to kptr_restrict.

echo 0 > /proc/sys/kernel/kptr_restrict

[Found by poking around in a random vendor kernel tree, it would be nice
if someone would actually send these types of patches upstream - gkh]

Signed-off-by: Vamsi Krishna Samavedam 
Cc: stable 
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Sasha Levin

USB: Proper handling of Race Condition when two USB class drivers try to call init_usb_class simultaneously

2017-05-17T19:07:44+00:00

[ Upstream commit 2f86a96be0ccb1302b7eee7855dbee5ce4dc5dfb ]

There is race condition when two USB class drivers try to call
init_usb_class at the same time and leads to crash.
code path: probe->usb_register_dev->init_usb_class

To solve this, mutex locking has been added in init_usb_class() and
destroy_usb_class().

As pointed by Alan, removed "if (usb_class)" test from destroy_usb_class()
because usb_class can never be NULL there.

Signed-off-by: Ajay Kaher 
Acked-by: Alan Stern 
Cc: stable 
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Sasha Levin

USB: fix linked-list corruption in rh_call_control()

2017-05-17T19:07:44+00:00

[ Upstream commit 1633682053a7ee8058e10c76722b9b28e97fb73f ]

Using KASAN, Dmitry found a bug in the rh_call_control() routine: If
buffer allocation fails, the routine returns immediately without
unlinking its URB from the control endpoint, eventually leading to
linked-list corruption.

This patch fixes the problem by jumping to the end of the routine
(where the URB is unlinked) when an allocation failure occurs.

Signed-off-by: Alan Stern 
Reported-and-tested-by: Dmitry Vyukov 
CC: 
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Sasha Levin

usb: hub: Do not attempt to autosuspend disconnected devices

2017-05-17T19:07:43+00:00

[ Upstream commit f5cccf49428447dfbc9edb7a04bb8fc316269781 ]

While running a bind/unbind stress test with the dwc3 usb driver on rk3399,
the following crash was observed.

Unable to handle kernel NULL pointer dereference at virtual address 00000218
pgd = ffffffc00165f000
[00000218] *pgd=000000000174f003, *pud=000000000174f003,
				*pmd=0000000001750003, *pte=00e8000001751713
Internal error: Oops: 96000005 [#1] PREEMPT SMP
Modules linked in: uinput uvcvideo videobuf2_vmalloc cmac
ipt_MASQUERADE nf_nat_masquerade_ipv4 iptable_nat nf_nat_ipv4 nf_nat rfcomm
xt_mark fuse bridge stp llc zram btusb btrtl btbcm btintel bluetooth
ip6table_filter mwifiex_pcie mwifiex cfg80211 cdc_ether usbnet r8152 mii joydev
snd_seq_midi snd_seq_midi_event snd_rawmidi snd_seq snd_seq_device ppp_async
ppp_generic slhc tun
CPU: 1 PID: 29814 Comm: kworker/1:1 Not tainted 4.4.52 #507
Hardware name: Google Kevin (DT)
Workqueue: pm pm_runtime_work
task: ffffffc0ac540000 ti: ffffffc0af4d4000 task.ti: ffffffc0af4d4000
PC is at autosuspend_check+0x74/0x174
LR is at autosuspend_check+0x70/0x174
...
Call trace:
[] autosuspend_check+0x74/0x174
[] usb_runtime_idle+0x20/0x40
[] __rpm_callback+0x48/0x7c
[] rpm_idle+0x1e8/0x498
[] pm_runtime_work+0x88/0xcc
[] process_one_work+0x390/0x6b8
[] worker_thread+0x480/0x610
[] kthread+0x164/0x178
[] ret_from_fork+0x10/0x40

Source:

(gdb) l *0xffffffc00080dcc0
0xffffffc00080dcc0 is in autosuspend_check
(drivers/usb/core/driver.c:1778).
1773		/* We don't need to check interfaces that are
1774		 * disabled for runtime PM.  Either they are unbound
1775		 * or else their drivers don't support autosuspend
1776		 * and so they are permanently active.
1777		 */
1778		if (intf->dev.power.disable_depth)
1779			continue;
1780		if (atomic_read(&intf->dev.power.usage_count) > 0)
1781			return -EBUSY;
1782		w |= intf->needs_remote_wakeup;

Code analysis shows that intf is set to NULL in usb_disable_device() prior
to setting actconfig to NULL. At the same time, usb_runtime_idle() does not
lock the usb device, and neither does any of the functions in the
traceback. This means that there is no protection against a race condition
where usb_disable_device() is removing dev->actconfig->interface[] pointers
while those are being accessed from autosuspend_check().

To solve the problem, synchronize and validate device state between
autosuspend_check() and usb_disconnect().

Acked-by: Alan Stern 
Signed-off-by: Guenter Roeck 
Cc: stable 
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Sasha Levin

usb: hub: Fix crash after failure to read BOS descriptor

2017-05-17T19:07:02+00:00

[ Upstream commit 7b2db29fbb4e766fcd02207eb2e2087170bd6ebc ]

If usb_get_bos_descriptor() returns an error, usb->bos will be NULL.
Nevertheless, it is dereferenced unconditionally in
hub_set_initial_usb2_lpm_policy() if usb2_hw_lpm_capable is set.
This results in a crash.

usb 5-1: unable to get BOS descriptor
...
Unable to handle kernel NULL pointer dereference at virtual address 00000008
pgd = ffffffc00165f000
[00000008] *pgd=000000000174f003, *pud=000000000174f003,
		*pmd=0000000001750003, *pte=00e8000001751713
Internal error: Oops: 96000005 [#1] PREEMPT SMP
Modules linked in: uinput uvcvideo videobuf2_vmalloc cmac [ ... ]
CPU: 5 PID: 3353 Comm: kworker/5:3 Tainted: G    B 4.4.52 #480
Hardware name: Google Kevin (DT)
Workqueue: events driver_set_config_work
task: ffffffc0c3690000 ti: ffffffc0ae9a8000 task.ti: ffffffc0ae9a8000
PC is at hub_port_init+0xc3c/0xd10
LR is at hub_port_init+0xc3c/0xd10
...
Call trace:
[] hub_port_init+0xc3c/0xd10
[] usb_reset_and_verify_device+0x15c/0x82c
[] usb_reset_device+0xe4/0x298
[] rtl8152_probe+0x84/0x9b0 [r8152]
[] usb_probe_interface+0x244/0x2f8
[] driver_probe_device+0x180/0x3b4
[] __device_attach_driver+0xb4/0xe0
[] bus_for_each_drv+0xb4/0xe4
[] __device_attach+0xd0/0x158
[] device_initial_probe+0x24/0x30
[] bus_probe_device+0x50/0xe4
[] device_add+0x414/0x738
[] usb_set_configuration+0x89c/0x914
[] driver_set_config_work+0xc0/0xf0
[] process_one_work+0x390/0x6b8
[] worker_thread+0x480/0x610
[] kthread+0x164/0x178
[] ret_from_fork+0x10/0x40

Since we don't know anything about LPM capabilities without BOS descriptor,
don't attempt to enable LPM if it is not available.

Fixes: 890dae886721 ("xhci: Enable LPM support only for hardwired ...")
Cc: stable 
Cc: Mathias Nyman 
Signed-off-by: Guenter Roeck 
Acked-by: Mathias Nyman 
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Sasha Levin

usb-core: Add LINEAR_FRAME_INTR_BINTERVAL USB quirk

2017-05-17T19:07:01+00:00

[ Upstream commit 3243367b209faed5c320a4e5f9a565ee2a2ba958 ]

Some USB 2.0 devices erroneously report millisecond values in
bInterval. The generic config code manages to catch most of them,
but in some cases it's not completely enough.

The case at stake here is a USB 2.0 braille device, which wants to
announce 10ms and thus sets bInterval to 10, but with the USB 2.0
computation that yields to 64ms.  It happens that one can type fast
enough to reach this interval and get the device buffers overflown,
leading to problematic latencies.  The generic config code does not
catch this case because the 64ms is considered a sane enough value.

This change thus adds a USB_QUIRK_LINEAR_FRAME_INTR_BINTERVAL quirk
to mark devices which actually report milliseconds in bInterval,
and marks Vario Ultra devices as needing it.

Signed-off-by: Samuel Thibault 
Acked-by: Alan Stern 
Cc: stable 
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Sasha Levin

USB: Add quirk for WORLDE easykey.25 MIDI keyboard

2017-03-06T22:31:11+00:00

[ Upstream commit d9b2997e4a0a874e452df7cdd7de5a54502bd0aa ]

Add a quirk for WORLDE easykey.25 MIDI keyboard (idVendor=0218,
idProduct=0401). The device reports that it has config string
descriptor at index 3, but when the system selects the configuration
and tries to get the description, it returns a -EPROTO error,
the communication restarts and this keeps repeating over and over again.
Not requesting the string descriptor makes the device work correctly.

Relevant info from Wireshark:

[...]

CONFIGURATION DESCRIPTOR
    bLength: 9
    bDescriptorType: 0x02 (CONFIGURATION)
    wTotalLength: 101
    bNumInterfaces: 2
    bConfigurationValue: 1
    iConfiguration: 3
    Configuration bmAttributes: 0xc0  SELF-POWERED  NO REMOTE-WAKEUP
        1... .... = Must be 1: Must be 1 for USB 1.1 and higher
        .1.. .... = Self-Powered: This device is SELF-POWERED
        ..0. .... = Remote Wakeup: This device does NOT support remote wakeup
    bMaxPower: 50  (100mA)

[...]

     45 0.369104       host                  2.38.0                USB      64     GET DESCRIPTOR Request STRING

[...]

URB setup
    bmRequestType: 0x80
        1... .... = Direction: Device-to-host
        .00. .... = Type: Standard (0x00)
        ...0 0000 = Recipient: Device (0x00)
    bRequest: GET DESCRIPTOR (6)
    Descriptor Index: 0x03
    bDescriptorType: 0x03
    Language Id: English (United States) (0x0409)
    wLength: 255

     46 0.369255       2.38.0                host                  USB      64     GET DESCRIPTOR Response STRING[Malformed Packet]

[...]

Frame 46: 64 bytes on wire (512 bits), 64 bytes captured (512 bits) on interface 0
USB URB
    [Source: 2.38.0]
    [Destination: host]
    URB id: 0xffff88021f62d480
    URB type: URB_COMPLETE ('C')
    URB transfer type: URB_CONTROL (0x02)
    Endpoint: 0x80, Direction: IN
    Device: 38
    URB bus id: 2
    Device setup request: not relevant ('-')
    Data: present (0)
    URB sec: 1484896277
    URB usec: 455031
    URB status: Protocol error (-EPROTO) (-71)
    URB length [bytes]: 0
    Data length [bytes]: 0
    [Request in: 45]
    [Time from request: 0.000151000 seconds]
    Unused Setup Header
    Interval: 0
    Start frame: 0
    Copy of Transfer Flags: 0x00000200
    Number of ISO descriptors: 0
[Malformed Packet: USB]
    [Expert Info (Error/Malformed): Malformed Packet (Exception occurred)]
        [Malformed Packet (Exception occurred)]
        [Severity level: Error]
        [Group: Malformed]

Signed-off-by: Lukáš Lalinský 
Cc: stable 
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Sasha Levin