linux-stable.git/drivers/usb/core, branch v4.1.16 Linux kernel stable tree usb: Use the USB_SS_MULT() macro to decode burst multiplier for log message 2016-01-23T04:54:11+00:00 Ben Hutchings ben@decadent.org.uk 2015-11-18T02:01:21+00:00 2518cb2956c7774dcbf5f361bdd9c126ec32b310 commit 5377adb092664d336ac212499961cac5e8728794 upstream. usb_parse_ss_endpoint_companion() now decodes the burst multiplier correctly in order to check that it's <= 3, but still uses the wrong expression if warning that it's > 3. Fixes: ff30cbc8da42 ("usb: Use the USB_SS_MULT() macro to get the ...") Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 5377adb092664d336ac212499961cac5e8728794 upstream.

usb_parse_ss_endpoint_companion() now decodes the burst multiplier
correctly in order to check that it's <= 3, but still uses the wrong
expression if warning that it's > 3.

Fixes: ff30cbc8da42 ("usb: Use the USB_SS_MULT() macro to get the ...")
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb: core : hub: Fix BOS 'NULL pointer' kernel panic 2016-01-23T04:54:10+00:00 Hans Yang hansy@nvidia.com 2015-12-01T08:54:59+00:00 c922602c0d2ae1f435d16b6124cfa1137ce83a7e commit 464ad8c43a9ead98c2b0eaed86bea727f2ad106e upstream. When a USB 3.0 mass storage device is disconnected in transporting state, storage device driver may handle it as a transport error and reset the device by invoking usb_reset_and_verify_device() and following could happen: in usb_reset_and_verify_device(): udev->bos = NULL; For U1/U2 enabled devices, driver will disable LPM, and in some conditions: from usb_unlocked_disable_lpm() --> usb_disable_lpm() --> usb_enable_lpm() udev->bos->ss_cap->bU1devExitLat; And it causes 'NULL pointer' and 'kernel panic': [ 157.976257] Unable to handle kernel NULL pointer dereference at virtual address 00000010 ... [ 158.026400] PC is at usb_enable_link_state+0x34/0x2e0 [ 158.031442] LR is at usb_enable_lpm+0x98/0xac ... [ 158.137368] [<ffffffc0006a1cac>] usb_enable_link_state+0x34/0x2e0 [ 158.143451] [<ffffffc0006a1fec>] usb_enable_lpm+0x94/0xac [ 158.148840] [<ffffffc0006a20e8>] usb_disable_lpm+0xa8/0xb4 ... [ 158.214954] Kernel panic - not syncing: Fatal exception This commit moves 'udev->bos = NULL' behind usb_unlocked_disable_lpm() to prevent from NULL pointer access. Issue can be reproduced by following setup: 1) A SS pen drive behind a SS hub connected to the host. 2) Transporting data between the pen drive and the host. 3) Abruptly disconnect hub and pen drive from host. 4) With a chance it crashes. Signed-off-by: Hans Yang <hansy@nvidia.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 464ad8c43a9ead98c2b0eaed86bea727f2ad106e upstream.

When a USB 3.0 mass storage device is disconnected in transporting
state, storage device driver may handle it as a transport error and
reset the device by invoking usb_reset_and_verify_device()
and following could happen:

in usb_reset_and_verify_device():
   udev->bos = NULL;

For U1/U2 enabled devices, driver will disable LPM, and in some
conditions:
   from usb_unlocked_disable_lpm()
    --> usb_disable_lpm()
    --> usb_enable_lpm()
        udev->bos->ss_cap->bU1devExitLat;

And it causes 'NULL pointer' and 'kernel panic':

[  157.976257] Unable to handle kernel NULL pointer dereference
at virtual address 00000010
...
[  158.026400] PC is at usb_enable_link_state+0x34/0x2e0
[  158.031442] LR is at usb_enable_lpm+0x98/0xac
...
[  158.137368] [<ffffffc0006a1cac>] usb_enable_link_state+0x34/0x2e0
[  158.143451] [<ffffffc0006a1fec>] usb_enable_lpm+0x94/0xac
[  158.148840] [<ffffffc0006a20e8>] usb_disable_lpm+0xa8/0xb4
...
[  158.214954] Kernel panic - not syncing: Fatal exception

This commit moves 'udev->bos = NULL' behind usb_unlocked_disable_lpm()
to prevent from NULL pointer access.

Issue can be reproduced by following setup:
1) A SS pen drive behind a SS hub connected to the host.
2) Transporting data between the pen drive and the host.
3) Abruptly disconnect hub and pen drive from host.
4) With a chance it crashes.

Signed-off-by: Hans Yang <hansy@nvidia.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB: add quirk for devices with broken LPM 2016-01-23T04:54:10+00:00 Alan Stern stern@rowland.harvard.edu 2015-12-10T20:27:21+00:00 04db25a46b25ac5c29082a61f96067c8cd5984ad commit ad87e03213b552a5c33d5e1e7a19a73768397010 upstream. Some USB device / host controller combinations seem to have problems with Link Power Management. For example, Steinar found that his xHCI controller wouldn't handle bandwidth calculations correctly for two video cards simultaneously when LPM was enabled, even though the bus had plenty of bandwidth available. This patch introduces a new quirk flag for devices that should remain disabled for LPM, and creates quirk entries for Steinar's devices. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-by: Steinar H. Gunderson <sgunderson@bigfoot.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit ad87e03213b552a5c33d5e1e7a19a73768397010 upstream.

Some USB device / host controller combinations seem to have problems
with Link Power Management.  For example, Steinar found that his xHCI
controller wouldn't handle bandwidth calculations correctly for two
video cards simultaneously when LPM was enabled, even though the bus
had plenty of bandwidth available.

This patch introduces a new quirk flag for devices that should remain
disabled for LPM, and creates quirk entries for Steinar's devices.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Steinar H. Gunderson <sgunderson@bigfoot.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB: Add reset-resume quirk for two Plantronics usb headphones. 2015-10-22T21:43:23+00:00 Yao-Wen Mao yaowen@google.com 2015-08-31T06:24:09+00:00 408bfba9544679db7a3c6a4268d4e668e35e5f0e commit 8484bf2981b3d006426ac052a3642c9ce1d8d980 upstream. These two headphones need a reset-resume quirk to properly resume to original volume level. Signed-off-by: Yao-Wen Mao <yaowen@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 8484bf2981b3d006426ac052a3642c9ce1d8d980 upstream.

These two headphones need a reset-resume quirk to properly resume to
original volume level.

Signed-off-by: Yao-Wen Mao <yaowen@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb: Add device quirk for Logitech PTZ cameras 2015-10-22T21:43:23+00:00 Vincent Palatin vpalatin@chromium.org 2015-10-01T21:10:22+00:00 866713d4ed8be3ced20229f31ce1ac9d4d96a7e9 commit 72194739f54607bbf8cfded159627a2015381557 upstream. Add a device quirk for the Logitech PTZ Pro Camera and its sibling the ConferenceCam CC3000e Camera. This fixes the failed camera enumeration on some boot, particularly on machines with fast CPU. Tested by connecting a Logitech PTZ Pro Camera to a machine with a Haswell Core i7-4600U CPU @ 2.10GHz, and doing thousands of reboot cycles while recording the kernel logs and taking camera picture after each boot. Before the patch, more than 7% of the boots show some enumeration transfer failures and in a few of them, the kernel is giving up before actually enumerating the webcam. After the patch, the enumeration has been correct on every reboot. Signed-off-by: Vincent Palatin <vpalatin@chromium.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 72194739f54607bbf8cfded159627a2015381557 upstream.

Add a device quirk for the Logitech PTZ Pro Camera and its sibling the
ConferenceCam CC3000e Camera.
This fixes the failed camera enumeration on some boot, particularly on
machines with fast CPU.

Tested by connecting a Logitech PTZ Pro Camera to a machine with a
Haswell Core i7-4600U CPU @ 2.10GHz, and doing thousands of reboot cycles
while recording the kernel logs and taking camera picture after each boot.
Before the patch, more than 7% of the boots show some enumeration transfer
failures and in a few of them, the kernel is giving up before actually
enumerating the webcam. After the patch, the enumeration has been correct
on every reboot.

Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb: Use the USB_SS_MULT() macro to get the burst multiplier. 2015-10-22T21:43:23+00:00 Mathias Nyman mathias.nyman@linux.intel.com 2015-09-21T14:46:09+00:00 74830c233c3c2dc4b034399f3d4d029e35db9a11 commit ff30cbc8da425754e8ab96904db1d295bd034f27 upstream. Bits 1:0 of the bmAttributes are used for the burst multiplier. The rest of the bits used to be reserved (zero), but USB3.1 takes bit 7 into use. Use the existing USB_SS_MULT() macro instead to make sure the mult value and hence max packet calculations are correct for USB3.1 devices. Note that burst multiplier in bmAttributes is zero based and that the USB_SS_MULT() macro adds one. Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit ff30cbc8da425754e8ab96904db1d295bd034f27 upstream.

Bits 1:0 of the bmAttributes are used for the burst multiplier.
The rest of the bits used to be reserved (zero), but USB3.1 takes bit 7
into use.

Use the existing USB_SS_MULT() macro instead to make sure the mult value
and hence max packet calculations are correct for USB3.1 devices.

Note that burst multiplier in bmAttributes is zero based and that
the USB_SS_MULT() macro adds one.

Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb: core: lpm: set lpm_capable for root hub device 2015-08-03T16:29:06+00:00 Lu Baolu baolu.lu@linux.intel.com 2015-06-16T01:08:26+00:00 e951f84074b84a3f5aecbffd01da74576e0068d5 commit 2d2a316765d956bc5cb6bb367b2ec52ca59ab8e9 upstream. Commit 25cd2882e2fc ("usb/xhci: Change how we indicate a host supports Link PM.") removed the code to set lpm_capable for USB 3.0 super-speed root hub. The intention of that change was to avoid touching usb core internal field, a.k.a. lpm_capable, and let usb core to set it by checking U1 and U2 exit latency values in the descriptor. Usb core checks and sets lpm_capable in hub_port_init(). Unfortunately, root hub is a special usb device as it has no parent. Hub_port_init() will never be called for a root hub device. That means lpm_capable will by no means be set for the root hub. As the result, lpm isn't functional at all in Linux kernel. This patch add the code to check and set lpm_capable when registering a root hub device. It could be back-ported to kernels as old as v3.15, that contains the Commit 25cd2882e2fc ("usb/xhci: Change how we indicate a host supports Link PM."). Reported-by: Kevin Strasser <kevin.strasser@linux.intel.com> Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 2d2a316765d956bc5cb6bb367b2ec52ca59ab8e9 upstream.

Commit 25cd2882e2fc ("usb/xhci: Change how we indicate a host supports
Link PM.") removed the code to set lpm_capable for USB 3.0 super-speed
root hub. The intention of that change was to avoid touching usb core
internal field, a.k.a. lpm_capable, and let usb core to set it by
checking U1 and U2 exit latency values in the descriptor.

Usb core checks and sets lpm_capable in hub_port_init(). Unfortunately,
root hub is a special usb device as it has no parent. Hub_port_init()
will never be called for a root hub device. That means lpm_capable will
by no means be set for the root hub. As the result, lpm isn't functional
at all in Linux kernel.

This patch add the code to check and set lpm_capable when registering a
root hub device. It could be back-ported to kernels as old as v3.15,
that contains the Commit 25cd2882e2fc ("usb/xhci: Change how we indicate
a host supports Link PM.").

Reported-by: Kevin Strasser <kevin.strasser@linux.intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB: devio: fix a condition in async_completed() 2015-08-03T16:29:05+00:00 Dan Carpenter dan.carpenter@oracle.com 2015-05-18T12:29:51+00:00 f32f8e6652d70c8453129fc4b9048a1eef6bc48c commit 83ed07c5db71bc02bd646d6eb60b48908235cdf9 upstream. Static checkers complain that the current condition is never true. It seems pretty likely that it's a typo and "URB" was intended instead of "USB". Fixes: 3d97ff63f899 ('usbdevfs: Use scatter-gather lists for large bulk transfers') Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 83ed07c5db71bc02bd646d6eb60b48908235cdf9 upstream.

Static checkers complain that the current condition is never true.  It
seems pretty likely that it's a typo and "URB" was intended instead of
"USB".

Fixes: 3d97ff63f899 ('usbdevfs: Use scatter-gather lists for large bulk transfers')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb: core: Fix USB 3.0 devices lost in NOTATTACHED state after a hub port reset 2015-08-03T16:29:05+00:00 Robert Schlabbach Robert.Schlabbach@gmx.net 2015-05-25T22:27:30+00:00 2c2e438cbb85386f4622626bfcb20f799980c9e1 commit fb6d1f7df5d25299fd7b3e84b72b8851d3634764 upstream. Fix USB 3.0 devices lost in NOTATTACHED state after a hub port reset. Dissolve the function hub_port_finish_reset() completely and divide the actions to be taken into those which need to be done after each reset attempt and those which need to be done after the full procedure is complete, and place them in the appropriate places in hub_port_reset(). Also, remove an unneeded forward declaration of hub_port_reset(). Verbose Problem Description: USB 3.0 devices may be "lost for good" during a hub port reset. This makes Linux unable to boot from USB 3.0 devices in certain constellations of host controllers and devices, because the USB device is lost during initialization, preventing the rootfs from being mounted. The underlying problem is that in the affected constellations, during the processing inside hub_port_reset(), the hub link state goes from 0 to SS.inactive after the initial reset, and back to 0 again only after the following "warm" reset. However, hub_port_finish_reset() is called after each reset attempt and sets the state the connected USB device based on the "preliminary" status of the hot reset to USB_STATE_NOTATTACHED due to SS.inactive, yet when the following warm reset is complete and hub_port_finish_reset() is called again, its call to set the device to USB_STATE_DEFAULT is blocked by usb_set_device_state() which does not allow taking USB devices out of USB_STATE_NOTATTACHED state. Thanks to Alan Stern for guiding me to the proper solution and how to submit it. Link: http://lkml.kernel.org/r/trinity-25981484-72a9-4d46-bf17-9c1cf9301a31-1432073240136%20()%203capp-gmx-bs27 Signed-off-by: Robert Schlabbach <robert_s@gmx.net> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit fb6d1f7df5d25299fd7b3e84b72b8851d3634764 upstream.

Fix USB 3.0 devices lost in NOTATTACHED state after a hub port reset.

Dissolve the function hub_port_finish_reset() completely and divide the
actions to be taken into those which need to be done after each reset
attempt and those which need to be done after the full procedure is
complete, and place them in the appropriate places in hub_port_reset().
Also, remove an unneeded forward declaration of hub_port_reset().

Verbose Problem Description:

USB 3.0 devices may be "lost for good" during a hub port reset.
This makes Linux unable to boot from USB 3.0 devices in certain
constellations of host controllers and devices, because the USB device is
lost during initialization, preventing the rootfs from being mounted.

The underlying problem is that in the affected constellations, during the
processing inside hub_port_reset(), the hub link state goes from 0 to
SS.inactive after the initial reset, and back to 0 again only after the
following "warm" reset.

However, hub_port_finish_reset() is called after each reset attempt and
sets the state the connected USB device based on the "preliminary" status
of the hot reset to USB_STATE_NOTATTACHED due to SS.inactive, yet when
the following warm reset is complete and hub_port_finish_reset() is
called again, its call to set the device to USB_STATE_DEFAULT is blocked
by usb_set_device_state() which does not allow taking USB devices out of
USB_STATE_NOTATTACHED state.

Thanks to Alan Stern for guiding me to the proper solution and how to
submit it.

Link: http://lkml.kernel.org/r/trinity-25981484-72a9-4d46-bf17-9c1cf9301a31-1432073240136%20()%203capp-gmx-bs27
Signed-off-by: Robert Schlabbach <robert_s@gmx.net>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Added another USB product ID for ELAN touchscreen quirks. 2015-05-09T17:23:03+00:00 Logan Gunthorpe logang@deltatee.com 2015-05-09T17:09:11+00:00 dc703ec22074d9c71a12da20670369fac3ea4296 I've had the same issue as described in commit c68929f75dfcb6354918862b91b5778585de1fa5 Except my touchscreen's ID is ID 04f3:0125 Elan Microelectronics Corp. Signed-off-by: Logan Gunthorpe <logang@deltatee.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
I've had the same issue as described in commit

c68929f75dfcb6354918862b91b5778585de1fa5

Except my touchscreen's ID is

ID 04f3:0125 Elan Microelectronics Corp.

Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>