linux-stable.git/drivers/usb/core, branch v3.2.94 Linux kernel stable tree Add USB quirk for HVR-950q to avoid intermittent device resets 2017-10-12T14:27:12+00:00 Devin Heitmueller dheitmueller@kernellabs.com 2017-06-27T17:08:51+00:00 bb9c4db48bf585cfaedfe10a109319286eab399d commit 6836796de4019944f4ba4c99a360e8250fd2e735 upstream. The USB core and sysfs will attempt to enumerate certain parameters which are unsupported by the au0828 - causing inconsistent behavior and sometimes causing the chip to reset. Avoid making these calls. This problem manifested as intermittent cases where the au8522 would be reset on analog video startup, in particular when starting up ALSA audio streaming in parallel - the sysfs entries created by snd-usb-audio on streaming startup would result in unsupported control messages being sent during tuning which would put the chip into an unknown state. Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk> 
commit 6836796de4019944f4ba4c99a360e8250fd2e735 upstream.

The USB core and sysfs will attempt to enumerate certain parameters
which are unsupported by the au0828 - causing inconsistent behavior
and sometimes causing the chip to reset.  Avoid making these calls.

This problem manifested as intermittent cases where the au8522 would
be reset on analog video startup, in particular when starting up ALSA
audio streaming in parallel - the sysfs entries created by
snd-usb-audio on streaming startup would result in unsupported control
messages being sent during tuning which would put the chip into an
unknown state.

Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
USB: hub: fix SS max number of ports 2017-09-15T17:30:43+00:00 Johan Hovold johan@kernel.org 2017-05-10T16:18:29+00:00 bef118e469b2de6eea62be03a18f0897782d63f8 commit 93491ced3c87c94b12220dbac0527e1356702179 upstream. Add define for the maximum number of ports on a SuperSpeed hub as per USB 3.1 spec Table 10-5, and use it when verifying the retrieved hub descriptor. This specifically avoids benign attempts to update the DeviceRemovable mask for non-existing ports (should we get that far). Fixes: dbe79bbe9dcb ("USB 3.0 Hub Changes") Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> [bwh: Backported to 3.2: - Add maxchild variable in hub_configure(), which was added separately upstream - Adjust filename] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> 
commit 93491ced3c87c94b12220dbac0527e1356702179 upstream.

Add define for the maximum number of ports on a SuperSpeed hub as per
USB 3.1 spec Table 10-5, and use it when verifying the retrieved hub
descriptor.

This specifically avoids benign attempts to update the DeviceRemovable
mask for non-existing ports (should we get that far).

Fixes: dbe79bbe9dcb ("USB 3.0 Hub Changes")
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.2:
 - Add maxchild variable in hub_configure(), which was added separately upstream
 - Adjust filename]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
USB: hub: fix non-SS hub-descriptor handling 2017-09-15T17:30:43+00:00 Johan Hovold johan@kernel.org 2017-05-10T16:18:28+00:00 21366032e35fcc1865aed5e5a1cd5eefc652afc7 commit bec444cd1c94c48df409a35ad4e5b143c245c3f7 upstream. Add missing sanity check on the non-SuperSpeed hub-descriptor length in order to avoid parsing and leaking two bytes of uninitialised slab data through sysfs removable-attributes (or a compound-device debug statement). Note that we only make sure that the DeviceRemovable field is always present (and specifically ignore the unused PortPwrCtrlMask field) in order to continue support any hubs with non-compliant descriptors. As a further safeguard, the descriptor buffer is also cleared. Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Johan Hovold <johan@kernel.org> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk> 
commit bec444cd1c94c48df409a35ad4e5b143c245c3f7 upstream.

Add missing sanity check on the non-SuperSpeed hub-descriptor length in
order to avoid parsing and leaking two bytes of uninitialised slab data
through sysfs removable-attributes (or a compound-device debug
statement).

Note that we only make sure that the DeviceRemovable field is always
present (and specifically ignore the unused PortPwrCtrlMask field) in
order to continue support any hubs with non-compliant descriptors. As a
further safeguard, the descriptor buffer is also cleared.

Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
USB: hub: fix SS hub-descriptor handling 2017-09-15T17:30:43+00:00 Johan Hovold johan@kernel.org 2017-05-10T16:18:27+00:00 53b8fef925e40a0bb2cbe9b32db9e6176891f953 commit 2c25a2c818023df64463aac3288a9f969491e507 upstream. A SuperSpeed hub descriptor does not have any variable-length fields so bail out when reading a short descriptor. This avoids parsing and leaking two bytes of uninitialised slab data through sysfs removable-attributes. Fixes: dbe79bbe9dcb ("USB 3.0 Hub Changes") Cc: John Youn <John.Youn@synopsys.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk> 
commit 2c25a2c818023df64463aac3288a9f969491e507 upstream.

A SuperSpeed hub descriptor does not have any variable-length fields so
bail out when reading a short descriptor.

This avoids parsing and leaking two bytes of uninitialised slab data
through sysfs removable-attributes.

Fixes: dbe79bbe9dcb ("USB 3.0 Hub Changes")
Cc: John Youn <John.Youn@synopsys.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
USB: core: replace %p with %pK 2017-09-15T17:30:42+00:00 Vamsi Krishna Samavedam vskrishn@codeaurora.org 2017-05-16T12:38:08+00:00 057747d4f85d37025224b302ec5ac3057b473f22 commit 2f964780c03b73de269b08d12aff96a9618d13f3 upstream. Format specifier %p can leak kernel addresses while not valuing the kptr_restrict system settings. When kptr_restrict is set to (1), kernel pointers printed using the %pK format specifier will be replaced with Zeros. Debugging Note : &pK prints only Zeros as address. If you need actual address information, write 0 to kptr_restrict. echo 0 > /proc/sys/kernel/kptr_restrict [Found by poking around in a random vendor kernel tree, it would be nice if someone would actually send these types of patches upstream - gkh] Signed-off-by: Vamsi Krishna Samavedam <vskrishn@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> [bwh: Backported to 3.2: drop changes in proc_reapurb*(), usbdev_do_ioctl(), usb_submit_urb()] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> 
commit 2f964780c03b73de269b08d12aff96a9618d13f3 upstream.

Format specifier %p can leak kernel addresses while not valuing the
kptr_restrict system settings. When kptr_restrict is set to (1), kernel
pointers printed using the %pK format specifier will be replaced with
Zeros. Debugging Note : &pK prints only Zeros as address. If you need
actual address information, write 0 to kptr_restrict.

echo 0 > /proc/sys/kernel/kptr_restrict

[Found by poking around in a random vendor kernel tree, it would be nice
if someone would actually send these types of patches upstream - gkh]

Signed-off-by: Vamsi Krishna Samavedam <vskrishn@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.2: drop changes in proc_reapurb*(), usbdev_do_ioctl(),
 usb_submit_urb()]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
USB: Proper handling of Race Condition when two USB class drivers try to call init_usb_class simultaneously 2017-08-26T01:13:58+00:00 Ajay Kaher ajay.kaher@samsung.com 2017-03-28T12:09:32+00:00 d3104d983465e23fb059cd32d34e8e35a8860fd2 commit 2f86a96be0ccb1302b7eee7855dbee5ce4dc5dfb upstream. There is race condition when two USB class drivers try to call init_usb_class at the same time and leads to crash. code path: probe->usb_register_dev->init_usb_class To solve this, mutex locking has been added in init_usb_class() and destroy_usb_class(). As pointed by Alan, removed "if (usb_class)" test from destroy_usb_class() because usb_class can never be NULL there. Signed-off-by: Ajay Kaher <ajay.kaher@samsung.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk> 
commit 2f86a96be0ccb1302b7eee7855dbee5ce4dc5dfb upstream.

There is race condition when two USB class drivers try to call
init_usb_class at the same time and leads to crash.
code path: probe->usb_register_dev->init_usb_class

To solve this, mutex locking has been added in init_usb_class() and
destroy_usb_class().

As pointed by Alan, removed "if (usb_class)" test from destroy_usb_class()
because usb_class can never be NULL there.

Signed-off-by: Ajay Kaher <ajay.kaher@samsung.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
usb: hub: Do not attempt to autosuspend disconnected devices 2017-08-26T01:13:57+00:00 Guenter Roeck linux@roeck-us.net 2017-03-20T21:30:50+00:00 c4c69518fc5f2d47bd285f6759cb25acbe487b97 commit f5cccf49428447dfbc9edb7a04bb8fc316269781 upstream. While running a bind/unbind stress test with the dwc3 usb driver on rk3399, the following crash was observed. Unable to handle kernel NULL pointer dereference at virtual address 00000218 pgd = ffffffc00165f000 [00000218] *pgd=000000000174f003, *pud=000000000174f003, *pmd=0000000001750003, *pte=00e8000001751713 Internal error: Oops: 96000005 [#1] PREEMPT SMP Modules linked in: uinput uvcvideo videobuf2_vmalloc cmac ipt_MASQUERADE nf_nat_masquerade_ipv4 iptable_nat nf_nat_ipv4 nf_nat rfcomm xt_mark fuse bridge stp llc zram btusb btrtl btbcm btintel bluetooth ip6table_filter mwifiex_pcie mwifiex cfg80211 cdc_ether usbnet r8152 mii joydev snd_seq_midi snd_seq_midi_event snd_rawmidi snd_seq snd_seq_device ppp_async ppp_generic slhc tun CPU: 1 PID: 29814 Comm: kworker/1:1 Not tainted 4.4.52 #507 Hardware name: Google Kevin (DT) Workqueue: pm pm_runtime_work task: ffffffc0ac540000 ti: ffffffc0af4d4000 task.ti: ffffffc0af4d4000 PC is at autosuspend_check+0x74/0x174 LR is at autosuspend_check+0x70/0x174 ... Call trace: [<ffffffc00080dcc0>] autosuspend_check+0x74/0x174 [<ffffffc000810500>] usb_runtime_idle+0x20/0x40 [<ffffffc000785ae0>] __rpm_callback+0x48/0x7c [<ffffffc000786af0>] rpm_idle+0x1e8/0x498 [<ffffffc000787cdc>] pm_runtime_work+0x88/0xcc [<ffffffc000249bb8>] process_one_work+0x390/0x6b8 [<ffffffc00024abcc>] worker_thread+0x480/0x610 [<ffffffc000251a80>] kthread+0x164/0x178 [<ffffffc0002045d0>] ret_from_fork+0x10/0x40 Source: (gdb) l *0xffffffc00080dcc0 0xffffffc00080dcc0 is in autosuspend_check (drivers/usb/core/driver.c:1778). 1773 /* We don't need to check interfaces that are 1774 * disabled for runtime PM. Either they are unbound 1775 * or else their drivers don't support autosuspend 1776 * and so they are permanently active. 1777 */ 1778 if (intf->dev.power.disable_depth) 1779 continue; 1780 if (atomic_read(&intf->dev.power.usage_count) > 0) 1781 return -EBUSY; 1782 w |= intf->needs_remote_wakeup; Code analysis shows that intf is set to NULL in usb_disable_device() prior to setting actconfig to NULL. At the same time, usb_runtime_idle() does not lock the usb device, and neither does any of the functions in the traceback. This means that there is no protection against a race condition where usb_disable_device() is removing dev->actconfig->interface[] pointers while those are being accessed from autosuspend_check(). To solve the problem, synchronize and validate device state between autosuspend_check() and usb_disconnect(). Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk> 
commit f5cccf49428447dfbc9edb7a04bb8fc316269781 upstream.

While running a bind/unbind stress test with the dwc3 usb driver on rk3399,
the following crash was observed.

Unable to handle kernel NULL pointer dereference at virtual address 00000218
pgd = ffffffc00165f000
[00000218] *pgd=000000000174f003, *pud=000000000174f003,
				*pmd=0000000001750003, *pte=00e8000001751713
Internal error: Oops: 96000005 [#1] PREEMPT SMP
Modules linked in: uinput uvcvideo videobuf2_vmalloc cmac
ipt_MASQUERADE nf_nat_masquerade_ipv4 iptable_nat nf_nat_ipv4 nf_nat rfcomm
xt_mark fuse bridge stp llc zram btusb btrtl btbcm btintel bluetooth
ip6table_filter mwifiex_pcie mwifiex cfg80211 cdc_ether usbnet r8152 mii joydev
snd_seq_midi snd_seq_midi_event snd_rawmidi snd_seq snd_seq_device ppp_async
ppp_generic slhc tun
CPU: 1 PID: 29814 Comm: kworker/1:1 Not tainted 4.4.52 #507
Hardware name: Google Kevin (DT)
Workqueue: pm pm_runtime_work
task: ffffffc0ac540000 ti: ffffffc0af4d4000 task.ti: ffffffc0af4d4000
PC is at autosuspend_check+0x74/0x174
LR is at autosuspend_check+0x70/0x174
...
Call trace:
[<ffffffc00080dcc0>] autosuspend_check+0x74/0x174
[<ffffffc000810500>] usb_runtime_idle+0x20/0x40
[<ffffffc000785ae0>] __rpm_callback+0x48/0x7c
[<ffffffc000786af0>] rpm_idle+0x1e8/0x498
[<ffffffc000787cdc>] pm_runtime_work+0x88/0xcc
[<ffffffc000249bb8>] process_one_work+0x390/0x6b8
[<ffffffc00024abcc>] worker_thread+0x480/0x610
[<ffffffc000251a80>] kthread+0x164/0x178
[<ffffffc0002045d0>] ret_from_fork+0x10/0x40

Source:

(gdb) l *0xffffffc00080dcc0
0xffffffc00080dcc0 is in autosuspend_check
(drivers/usb/core/driver.c:1778).
1773		/* We don't need to check interfaces that are
1774		 * disabled for runtime PM.  Either they are unbound
1775		 * or else their drivers don't support autosuspend
1776		 * and so they are permanently active.
1777		 */
1778		if (intf->dev.power.disable_depth)
1779			continue;
1780		if (atomic_read(&intf->dev.power.usage_count) > 0)
1781			return -EBUSY;
1782		w |= intf->needs_remote_wakeup;

Code analysis shows that intf is set to NULL in usb_disable_device() prior
to setting actconfig to NULL. At the same time, usb_runtime_idle() does not
lock the usb device, and neither does any of the functions in the
traceback. This means that there is no protection against a race condition
where usb_disable_device() is removing dev->actconfig->interface[] pointers
while those are being accessed from autosuspend_check().

To solve the problem, synchronize and validate device state between
autosuspend_check() and usb_disconnect().

Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
usb: hub: Fix error loop seen after hub communication errors 2017-08-26T01:13:57+00:00 Guenter Roeck linux@roeck-us.net 2017-03-20T18:16:11+00:00 a2b0358b2c4ebb194c0a69a1834d6099fba8fe8b commit 245b2eecee2aac6fdc77dcafaa73c33f9644c3c7 upstream. While stress testing a usb controller using a bind/unbind looop, the following error loop was observed. usb 7-1.2: new low-speed USB device number 3 using xhci-hcd usb 7-1.2: hub failed to enable device, error -108 usb 7-1-port2: cannot disable (err = -22) usb 7-1-port2: couldn't allocate usb_device usb 7-1-port2: cannot disable (err = -22) hub 7-1:1.0: hub_ext_port_status failed (err = -22) hub 7-1:1.0: hub_ext_port_status failed (err = -22) hub 7-1:1.0: activate --> -22 hub 7-1:1.0: hub_ext_port_status failed (err = -22) hub 7-1:1.0: hub_ext_port_status failed (err = -22) hub 7-1:1.0: activate --> -22 hub 7-1:1.0: hub_ext_port_status failed (err = -22) hub 7-1:1.0: hub_ext_port_status failed (err = -22) hub 7-1:1.0: activate --> -22 hub 7-1:1.0: hub_ext_port_status failed (err = -22) hub 7-1:1.0: hub_ext_port_status failed (err = -22) hub 7-1:1.0: activate --> -22 hub 7-1:1.0: hub_ext_port_status failed (err = -22) hub 7-1:1.0: hub_ext_port_status failed (err = -22) hub 7-1:1.0: activate --> -22 hub 7-1:1.0: hub_ext_port_status failed (err = -22) hub 7-1:1.0: hub_ext_port_status failed (err = -22) hub 7-1:1.0: activate --> -22 hub 7-1:1.0: hub_ext_port_status failed (err = -22) hub 7-1:1.0: hub_ext_port_status failed (err = -22) hub 7-1:1.0: activate --> -22 hub 7-1:1.0: hub_ext_port_status failed (err = -22) hub 7-1:1.0: hub_ext_port_status failed (err = -22) hub 7-1:1.0: activate --> -22 hub 7-1:1.0: hub_ext_port_status failed (err = -22) hub 7-1:1.0: hub_ext_port_status failed (err = -22) ** 57 printk messages dropped ** hub 7-1:1.0: activate --> -22 ** 82 printk messages dropped ** hub 7-1:1.0: hub_ext_port_status failed (err = -22) This continues forever. After adding tracebacks into the code, the call sequence leading to this is found to be as follows. [<ffffffc0007fc8e0>] hub_activate+0x368/0x7b8 [<ffffffc0007fceb4>] hub_resume+0x2c/0x3c [<ffffffc00080b3b8>] usb_resume_interface.isra.6+0x128/0x158 [<ffffffc00080b5d0>] usb_suspend_both+0x1e8/0x288 [<ffffffc00080c9c4>] usb_runtime_suspend+0x3c/0x98 [<ffffffc0007820a0>] __rpm_callback+0x48/0x7c [<ffffffc00078217c>] rpm_callback+0xa8/0xd4 [<ffffffc000786234>] rpm_suspend+0x84/0x758 [<ffffffc000786ca4>] rpm_idle+0x2c8/0x498 [<ffffffc000786ed4>] __pm_runtime_idle+0x60/0xac [<ffffffc00080eba8>] usb_autopm_put_interface+0x6c/0x7c [<ffffffc000803798>] hub_event+0x10ac/0x12ac [<ffffffc000249bb8>] process_one_work+0x390/0x6b8 [<ffffffc00024abcc>] worker_thread+0x480/0x610 [<ffffffc000251a80>] kthread+0x164/0x178 [<ffffffc0002045d0>] ret_from_fork+0x10/0x40 kick_hub_wq() is called from hub_activate() even after failures to communicate with the hub. This results in an endless sequence of hub event -> hub activate -> wq trigger -> hub event -> ... Provide two solutions for the problem. - Only trigger the hub event queue if communication with the hub is successful. - After a suspend failure, only resume already suspended interfaces if the communication with the device is still possible. Each of the changes fixes the observed problem. Use both to improve robustness. Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> [bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> 
commit 245b2eecee2aac6fdc77dcafaa73c33f9644c3c7 upstream.

While stress testing a usb controller using a bind/unbind looop, the
following error loop was observed.

usb 7-1.2: new low-speed USB device number 3 using xhci-hcd
usb 7-1.2: hub failed to enable device, error -108
usb 7-1-port2: cannot disable (err = -22)
usb 7-1-port2: couldn't allocate usb_device
usb 7-1-port2: cannot disable (err = -22)
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
hub 7-1:1.0: activate --> -22
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
hub 7-1:1.0: activate --> -22
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
hub 7-1:1.0: activate --> -22
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
hub 7-1:1.0: activate --> -22
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
hub 7-1:1.0: activate --> -22
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
hub 7-1:1.0: activate --> -22
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
hub 7-1:1.0: activate --> -22
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
hub 7-1:1.0: activate --> -22
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
** 57 printk messages dropped ** hub 7-1:1.0: activate --> -22
** 82 printk messages dropped ** hub 7-1:1.0: hub_ext_port_status failed (err = -22)

This continues forever. After adding tracebacks into the code,
the call sequence leading to this is found to be as follows.

[<ffffffc0007fc8e0>] hub_activate+0x368/0x7b8
[<ffffffc0007fceb4>] hub_resume+0x2c/0x3c
[<ffffffc00080b3b8>] usb_resume_interface.isra.6+0x128/0x158
[<ffffffc00080b5d0>] usb_suspend_both+0x1e8/0x288
[<ffffffc00080c9c4>] usb_runtime_suspend+0x3c/0x98
[<ffffffc0007820a0>] __rpm_callback+0x48/0x7c
[<ffffffc00078217c>] rpm_callback+0xa8/0xd4
[<ffffffc000786234>] rpm_suspend+0x84/0x758
[<ffffffc000786ca4>] rpm_idle+0x2c8/0x498
[<ffffffc000786ed4>] __pm_runtime_idle+0x60/0xac
[<ffffffc00080eba8>] usb_autopm_put_interface+0x6c/0x7c
[<ffffffc000803798>] hub_event+0x10ac/0x12ac
[<ffffffc000249bb8>] process_one_work+0x390/0x6b8
[<ffffffc00024abcc>] worker_thread+0x480/0x610
[<ffffffc000251a80>] kthread+0x164/0x178
[<ffffffc0002045d0>] ret_from_fork+0x10/0x40

kick_hub_wq() is called from hub_activate() even after failures to
communicate with the hub. This results in an endless sequence of
hub event -> hub activate -> wq trigger -> hub event -> ...

Provide two solutions for the problem.

- Only trigger the hub event queue if communication with the hub
  is successful.
- After a suspend failure, only resume already suspended interfaces
  if the communication with the device is still possible.

Each of the changes fixes the observed problem. Use both to improve
robustness.

Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
usb-core: Add LINEAR_FRAME_INTR_BINTERVAL USB quirk 2017-07-18T17:38:33+00:00 Samuel Thibault samuel.thibault@ens-lyon.org 2017-03-13T19:50:08+00:00 39648aa496999bcfb9d1edf61566914fcdec9a34 commit 3243367b209faed5c320a4e5f9a565ee2a2ba958 upstream. Some USB 2.0 devices erroneously report millisecond values in bInterval. The generic config code manages to catch most of them, but in some cases it's not completely enough. The case at stake here is a USB 2.0 braille device, which wants to announce 10ms and thus sets bInterval to 10, but with the USB 2.0 computation that yields to 64ms. It happens that one can type fast enough to reach this interval and get the device buffers overflown, leading to problematic latencies. The generic config code does not catch this case because the 64ms is considered a sane enough value. This change thus adds a USB_QUIRK_LINEAR_FRAME_INTR_BINTERVAL quirk to mark devices which actually report milliseconds in bInterval, and marks Vario Ultra devices as needing it. Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk> 
commit 3243367b209faed5c320a4e5f9a565ee2a2ba958 upstream.

Some USB 2.0 devices erroneously report millisecond values in
bInterval. The generic config code manages to catch most of them,
but in some cases it's not completely enough.

The case at stake here is a USB 2.0 braille device, which wants to
announce 10ms and thus sets bInterval to 10, but with the USB 2.0
computation that yields to 64ms.  It happens that one can type fast
enough to reach this interval and get the device buffers overflown,
leading to problematic latencies.  The generic config code does not
catch this case because the 64ms is considered a sane enough value.

This change thus adds a USB_QUIRK_LINEAR_FRAME_INTR_BINTERVAL quirk
to mark devices which actually report milliseconds in bInterval,
and marks Vario Ultra devices as needing it.

Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
USB: Add quirk for WORLDE easykey.25 MIDI keyboard 2017-03-16T02:18:46+00:00 Lukáš Lalinský lukas@oxygene.sk 2017-01-20T18:46:34+00:00 c1b1c26e9df754f56776cee2978c626e786c1c86 commit d9b2997e4a0a874e452df7cdd7de5a54502bd0aa upstream. Add a quirk for WORLDE easykey.25 MIDI keyboard (idVendor=0218, idProduct=0401). The device reports that it has config string descriptor at index 3, but when the system selects the configuration and tries to get the description, it returns a -EPROTO error, the communication restarts and this keeps repeating over and over again. Not requesting the string descriptor makes the device work correctly. Relevant info from Wireshark: [...] CONFIGURATION DESCRIPTOR bLength: 9 bDescriptorType: 0x02 (CONFIGURATION) wTotalLength: 101 bNumInterfaces: 2 bConfigurationValue: 1 iConfiguration: 3 Configuration bmAttributes: 0xc0 SELF-POWERED NO REMOTE-WAKEUP 1... .... = Must be 1: Must be 1 for USB 1.1 and higher .1.. .... = Self-Powered: This device is SELF-POWERED ..0. .... = Remote Wakeup: This device does NOT support remote wakeup bMaxPower: 50 (100mA) [...] 45 0.369104 host 2.38.0 USB 64 GET DESCRIPTOR Request STRING [...] URB setup bmRequestType: 0x80 1... .... = Direction: Device-to-host .00. .... = Type: Standard (0x00) ...0 0000 = Recipient: Device (0x00) bRequest: GET DESCRIPTOR (6) Descriptor Index: 0x03 bDescriptorType: 0x03 Language Id: English (United States) (0x0409) wLength: 255 46 0.369255 2.38.0 host USB 64 GET DESCRIPTOR Response STRING[Malformed Packet] [...] Frame 46: 64 bytes on wire (512 bits), 64 bytes captured (512 bits) on interface 0 USB URB [Source: 2.38.0] [Destination: host] URB id: 0xffff88021f62d480 URB type: URB_COMPLETE ('C') URB transfer type: URB_CONTROL (0x02) Endpoint: 0x80, Direction: IN Device: 38 URB bus id: 2 Device setup request: not relevant ('-') Data: present (0) URB sec: 1484896277 URB usec: 455031 URB status: Protocol error (-EPROTO) (-71) URB length [bytes]: 0 Data length [bytes]: 0 [Request in: 45] [Time from request: 0.000151000 seconds] Unused Setup Header Interval: 0 Start frame: 0 Copy of Transfer Flags: 0x00000200 Number of ISO descriptors: 0 [Malformed Packet: USB] [Expert Info (Error/Malformed): Malformed Packet (Exception occurred)] [Malformed Packet (Exception occurred)] [Severity level: Error] [Group: Malformed] Signed-off-by: Lukáš Lalinský <lukas@oxygene.sk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk> 
commit d9b2997e4a0a874e452df7cdd7de5a54502bd0aa upstream.

Add a quirk for WORLDE easykey.25 MIDI keyboard (idVendor=0218,
idProduct=0401). The device reports that it has config string
descriptor at index 3, but when the system selects the configuration
and tries to get the description, it returns a -EPROTO error,
the communication restarts and this keeps repeating over and over again.
Not requesting the string descriptor makes the device work correctly.

Relevant info from Wireshark:

[...]

CONFIGURATION DESCRIPTOR
    bLength: 9
    bDescriptorType: 0x02 (CONFIGURATION)
    wTotalLength: 101
    bNumInterfaces: 2
    bConfigurationValue: 1
    iConfiguration: 3
    Configuration bmAttributes: 0xc0  SELF-POWERED  NO REMOTE-WAKEUP
        1... .... = Must be 1: Must be 1 for USB 1.1 and higher
        .1.. .... = Self-Powered: This device is SELF-POWERED
        ..0. .... = Remote Wakeup: This device does NOT support remote wakeup
    bMaxPower: 50  (100mA)

[...]

     45 0.369104       host                  2.38.0                USB      64     GET DESCRIPTOR Request STRING

[...]

URB setup
    bmRequestType: 0x80
        1... .... = Direction: Device-to-host
        .00. .... = Type: Standard (0x00)
        ...0 0000 = Recipient: Device (0x00)
    bRequest: GET DESCRIPTOR (6)
    Descriptor Index: 0x03
    bDescriptorType: 0x03
    Language Id: English (United States) (0x0409)
    wLength: 255

     46 0.369255       2.38.0                host                  USB      64     GET DESCRIPTOR Response STRING[Malformed Packet]

[...]

Frame 46: 64 bytes on wire (512 bits), 64 bytes captured (512 bits) on interface 0
USB URB
    [Source: 2.38.0]
    [Destination: host]
    URB id: 0xffff88021f62d480
    URB type: URB_COMPLETE ('C')
    URB transfer type: URB_CONTROL (0x02)
    Endpoint: 0x80, Direction: IN
    Device: 38
    URB bus id: 2
    Device setup request: not relevant ('-')
    Data: present (0)
    URB sec: 1484896277
    URB usec: 455031
    URB status: Protocol error (-EPROTO) (-71)
    URB length [bytes]: 0
    Data length [bytes]: 0
    [Request in: 45]
    [Time from request: 0.000151000 seconds]
    Unused Setup Header
    Interval: 0
    Start frame: 0
    Copy of Transfer Flags: 0x00000200
    Number of ISO descriptors: 0
[Malformed Packet: USB]
    [Expert Info (Error/Malformed): Malformed Packet (Exception occurred)]
        [Malformed Packet (Exception occurred)]
        [Severity level: Error]
        [Group: Malformed]

Signed-off-by: Lukáš Lalinský <lukas@oxygene.sk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>