linux-stable.git/drivers/usb/core, branch v3.2.65

usb-quirks: Add reset-resume quirk for MS Wireless Laser Mouse 6000

2014-12-14T16:24:00+00:00

commit 263e80b43559a6103e178a9176938ce171b23872 upstream.

This wireless mouse receiver needs a reset-resume quirk to properly come
out of reset.

BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1165206
Signed-off-by: Hans de Goede 
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Ben Hutchings

usb: Do not allow usb_alloc_streams on unconfigured devices

2014-12-14T16:23:54+00:00

commit 90a646c770c50cc206ceba0d7b50453c46c13c36 upstream.

This commit fixes the following oops:

[10238.622067] scsi host3: uas_eh_bus_reset_handler start
[10240.766164] usb 3-4: reset SuperSpeed USB device number 3 using xhci_hcd
[10245.779365] usb 3-4: device descriptor read/8, error -110
[10245.883331] usb 3-4: reset SuperSpeed USB device number 3 using xhci_hcd
[10250.897603] usb 3-4: device descriptor read/8, error -110
[10251.058200] BUG: unable to handle kernel NULL pointer dereference at  0000000000000040
[10251.058244] IP: [] xhci_check_streams_endpoint+0x91/0x140

[10251.059473] Call Trace:
[10251.059487]  [] xhci_calculate_streams_and_bitmask+0xbc/0x130
[10251.059520]  [] xhci_alloc_streams+0x10f/0x5a0
[10251.059548]  [] ? check_preempt_curr+0x75/0xa0
[10251.059575]  [] ? ttwu_do_wakeup+0x2c/0x100
[10251.059601]  [] ? ttwu_do_activate.constprop.111+0x66/0x70
[10251.059635]  [] usb_alloc_streams+0xab/0xf0
[10251.059662]  [] uas_configure_endpoints+0x128/0x150 [uas]
[10251.059694]  [] uas_post_reset+0x3c/0xb0 [uas]
[10251.059722]  [] usb_reset_device+0x1b9/0x2a0
[10251.059749]  [] uas_eh_bus_reset_handler+0xb2/0x190 [uas]
[10251.059781]  [] scsi_try_bus_reset+0x53/0x110
[10251.059808]  [] scsi_eh_bus_reset+0xf7/0x270


The problem is the following call sequence (simplified):

1) usb_reset_device
2)  usb_reset_and_verify_device
2)   hub_port_init
3)    hub_port_finish_reset
3)     xhci_discover_or_reset_device
        This frees xhci->devs[slot_id]->eps[ep_index].ring for all eps but 0
4)    usb_get_device_descriptor
       This fails
5)   hub_port_init fails
6)  usb_reset_and_verify_device fails, does not restore device config
7)  uas_post_reset
8)   xhci_alloc_streams
      NULL deref on the free-ed ring

This commit fixes this by not allowing usb_alloc_streams to continue if
the device is not configured.

Note that we do allow usb_free_streams to continue after a (logical)
disconnect, as it is necessary to explicitly free the streams at the xhci
controller level.

Signed-off-by: Hans de Goede 
Acked-by: Alan Stern 
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Ben Hutchings

USB: Add device quirk for ASUS T100 Base Station keyboard

2014-12-14T16:23:43+00:00

commit ddbe1fca0bcb87ca8c199ea873a456ca8a948567 upstream.

This full-speed USB device generates spurious remote wakeup event
as soon as USB_DEVICE_REMOTE_WAKEUP feature is set. As the result,
Linux can't enter system suspend and S0ix power saving modes once
this keyboard is used.

This patch tries to introduce USB_QUIRK_IGNORE_REMOTE_WAKEUP quirk.
With this quirk set, wakeup capability will be ignored during
device configure.

This patch could be back-ported to kernels as old as 2.6.39.

Signed-off-by: Lu Baolu 
Acked-by: Alan Stern 
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Ben Hutchings

USB: add reset resume quirk for usb3503

2014-12-14T16:23:43+00:00

commit 526a4045c60fbaede88ec95a69a73059dff02160 upstream.

The usb device will autoresume from choose_wakeup() if it is
autosuspended with the wrong wakeup setting, but below errors occur
because usb3503 misc driver will switch to standby mode when suspended.

As add USB_QUIRK_RESET_RESUME, it can stop setting wrong wakeup from
autosuspend_check().

[    7.734717] usb 1-3: reset high-speed USB device number 3 using exynos-ehci
[    7.854658] usb 1-3: device descriptor read/64, error -71
[    8.079657] usb 1-3: device descriptor read/64, error -71
[    8.294664] usb 1-3: reset high-speed USB device number 3 using exynos-ehci
[    8.414658] usb 1-3: device descriptor read/64, error -71
[    8.639657] usb 1-3: device descriptor read/64, error -71
[    8.854667] usb 1-3: reset high-speed USB device number 3 using exynos-ehci
[    9.264598] usb 1-3: device not accepting address 3, error -71
[    9.374655] usb 1-3: reset high-speed USB device number 3 using exynos-ehci
[    9.784601] usb 1-3: device not accepting address 3, error -71
[    9.784838] usb usb1-port3: device 1-3 not suspended yet

Signed-off-by: Joonyoung Shim 
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Ben Hutchings

usb: hub: take hub->hdev reference when processing from eventlist

2014-11-05T20:27:42+00:00

commit c605f3cdff53a743f6d875b76956b239deca1272 upstream.

During surprise device hotplug removal tests, it was observed that
hub_events may try to call usb_lock_device on a device that has already
been freed. Protect the usb_device by taking out a reference (under the
hub_event_lock) when hub_events pulls it off the list, returning the
reference after hub_events is finished using it.

Signed-off-by: Joe Lawrence 
Suggested-by: David Bulkow  for using kref
Suggested-by: Alan Stern  for placement
Acked-by: Alan Stern 
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Ben Hutchings

USB: Fix persist resume of some SS USB devices

2014-09-13T22:41:39+00:00

commit a40178b2fa6ad87670fb1e5fa4024db00c149629 upstream.

Problem Summary: Problem has been observed generally with PM states
where VBUS goes off during suspend. There are some SS USB devices which
take longer time for link training compared to many others.  Such
devices fail to reconnect with same old address which was associated
with it before suspend.

When system resumes, at some point of time (dpm_run_callback->
usb_dev_resume->usb_resume->usb_resume_both->usb_resume_device->
usb_port_resume) SW reads hub status. If device is present,
then it finishes port resume and re-enumerates device with same
address. If device is not present then, SW thinks that device was
removed during suspend and therefore does logical disconnection
and removes all the resource allocated for this device.

Now, if I put sufficient delay just before root hub status read in
usb_resume_device then, SW sees always that device is present. In normal
course(without any delay) SW sees that no device is present and then SW
removes all resource associated with the device at this port.  In the
latter case, after sometime, device says that hey I am here, now host
enumerates it, but with new address.

Problem had been reproduced when I connect verbatim USB3.0 hard disc
with my STiH407 XHCI host running with 3.10 kernel.

I see that similar problem has been reported here.
https://bugzilla.kernel.org/show_bug.cgi?id=53211
Reading above it seems that bug was not in 3.6.6 and was present in 3.8
and again it was not present for some in 3.12.6, while it was present
for few others. I tested with 3.13-FC19 running at i686 desktop, problem
was still there. However, I was failed to reproduce it with 3.16-RC4
running at same i686 machine. I would say it is just a random
observation. Problem for few devices is always there, as I am unable to
find a proper fix for the issue.

So, now question is what should be the amount of delay so that host is
always able to recognize suspended device after resume.

XHCI specs 4.19.4 says that when Link training is successful, port sets
CSC bit to 1. So if SW reads port status before successful link
training, then it will not find device to be present.  USB Analyzer log
with such buggy devices show that in some cases device switch on the
RX termination after long delay of host enabling the VBUS. In few other
cases it has been seen that device fails to negotiate link training in
first attempt. It has been reported till now that few devices take as
long as 2000 ms to train the link after host enabling its VBUS and
RX termination. This patch implements a 2000 ms timeout for CSC bit to set
ie for link training. If in a case link trains before timeout, loop will
exit earlier.

This patch implements above delay, but only for SS device and when
persist is enabled.

So, for the good device overhead is almost none. While for the bad
devices penalty could be the time which it take for link training.
But, If a device was connected before suspend, and was removed
while system was asleep, then the penalty would be the timeout ie
2000 ms.

Results:

Verbatim USB SS hard disk connected with STiH407 USB host running 3.10
Kernel resumes in 461 msecs without this patch, but hard disk is
assigned a new device address. Same system resumes in 790 msecs with
this patch, but with old device address.

Signed-off-by: Pratyush Anand 
Acked-by: Alan Stern 
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Ben Hutchings

usbcore: don't log on consecutive debounce failures of the same port

2014-09-13T22:41:38+00:00

commit 5ee0f803cc3a0738a63288e4a2f453c85889fbda upstream.

Some laptops have an internal port for a BT device which picks
up noise when the kill switch is used, but not enough to trigger
printk_rlimit(). So we shouldn't log consecutive faults of this kind.

Signed-off-by: Oliver Neukum 
Signed-off-by: Greg Kroah-Hartman 
[bwh: Backported to 3.2:
 - Adjust context
 - Error message already includes the port number]
Signed-off-by: Ben Hutchings

usb: Check if port status is equal to RxDetect

2014-08-06T17:07:38+00:00

commit bb86cf569bbd7ad4dce581a37c7fbd748057e9dc upstream.

When using USB 3.0 pen drive with the [AMD] FCH USB XHCI Controller
[1022:7814], the second hotplugging will experience the USB 3.0 pen
drive is recognized as high-speed device. After bisecting the kernel,
I found the commit number 41e7e056cdc662f704fa9262e5c6e213b4ab45dd
(USB: Allow USB 3.0 ports to be disabled.) causes the bug. After doing
some experiments, the bug can be fixed by avoiding executing the function
hub_usb3_port_disable(). Because the port status with [AMD] FCH USB
XHCI Controlleris [1022:7814] is already in RxDetect
(I tried printing out the port status before setting to Disabled state),
it's reasonable to check the port status before really executing
hub_usb3_port_disable().

Fixes: 41e7e056cdc6 (USB: Allow USB 3.0 ports to be disabled.)
Signed-off-by: Gavin Guo 
Acked-by: Alan Stern 
Signed-off-by: Greg Kroah-Hartman 
[bwh: Backported to 3.2: use hub device as context for dev_dbg(),
 as hub ports are not devices in their own right]
Signed-off-by: Ben Hutchings

USB: Avoid runtime suspend loops for HCDs that can't handle suspend/resume

2014-07-11T12:33:36+00:00

commit 8ef42ddd9a53b73e6fc3934278710c27f80f324f upstream.

Not all host controller drivers have bus-suspend and bus-resume
methods.  When one doesn't, it will cause problems if runtime PM is
enabled in the kernel.  The PM core will attempt to suspend the
controller's root hub, the suspend will fail because there is no
bus-suspend routine, and a -EBUSY error code will be returned to the
PM core.  This will cause the suspend attempt to be repeated shortly
thereafter, in a never-ending loop.

Part of the problem is that the original error code -ENOENT gets
changed to -EBUSY in usb_runtime_suspend(), on the grounds that the PM
core will interpret -ENOENT as meaning that the root hub has gotten
into a runtime-PM error state.  While this change is appropriate for
real USB devices, it's not such a good idea for a root hub.  In fact,
considering the root hub to be in a runtime-PM error state would not
be far from the truth.  Therefore this patch updates
usb_runtime_suspend() so that it adjusts error codes only for
non-root-hub devices.

Furthermore, the patch attempts to prevent the problem from occurring
in the first place by not enabling runtime PM by default for root hubs
whose host controller driver doesn't have bus_suspend and bus_resume
methods.

Signed-off-by: Alan Stern 
Reported-by: Will Deacon 
Tested-by: Will Deacon 
Signed-off-by: Greg Kroah-Hartman 
[bwh: Backported to 3.2: runtime PM is also not supported for USB 3.0
 non-root hubs]
Signed-off-by: Ben Hutchings

usb: Make DELAY_INIT quirk wait 100ms between Get Configuration requests

2014-04-01T23:58:58+00:00

commit d86db25e53fa69e3e97f3b55dd82a70689787c5d upstream.

The DELAY_INIT quirk only reduces the frequency of enumeration failures
with the Logitech HD Pro C920 and C930e webcams, but does not quite
eliminate them. We have found that adding a delay of 100ms between the
first and second Get Configuration request makes the device enumerate
perfectly reliable even after several weeks of extensive testing. The
reasons for that are anyone's guess, but since the DELAY_INIT quirk
already delays enumeration by a whole second, wating for another 10th of
that isn't really a big deal for the one other device that uses it, and
it will resolve the problems with these webcams.

Signed-off-by: Julius Werner 
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Ben Hutchings