linux-stable.git/drivers/usb/core, branch v3.18.67

usb:xhci:Add quirk for Certain failing HP keyboard on reset after resume

2017-08-16T20:35:31+00:00

commit e788787ef4f9c24aafefc480a8da5f92b914e5e6 upstream.

Certain HP keyboards would keep inputting a character automatically which
is the wake-up key after S3 resume

On some AMD platforms USB host fails to respond (by holding resume-K) to
USB device (an HP keyboard) resume request within 1ms (TURSM) and ensures
that resume is signaled for at least 20 ms (TDRSMDN), which is defined in
USB 2.0 spec. The result is that the keyboard is out of function.

In SNPS USB design, the host responds to the resume request only after
system gets back to S0 and the host gets to functional after the internal
HW restore operation that is more than 1 second after the initial resume
request from the USB device.

As a workaround for specific keyboard ID(HP Keyboards), applying port reset
after resume when the keyboard is plugged in.

Signed-off-by: Sandeep Singh 
Signed-off-by: Shyam Sundar S K 
cc: Nehal Shah 
Reviewed-by: Felipe Balbi 
Signed-off-by: Greg Kroah-Hartman

usb: quirks: Add no-lpm quirk for Moshi USB to Ethernet Adapter

2017-08-16T20:35:31+00:00

commit 7496cfe5431f21da5d27a8388c326397e3f0a5db upstream.

Moshi USB to Ethernet Adapter internally uses a Genesys Logic hub to
connect to Realtek r8153.

The Realtek r8153 ethernet does not work on the internal hub, no-lpm quirk
can make it work.

Since another r8153 dongle at my hand does not have the issue, so add
the quirk to the Genesys Logic hub instead.

Signed-off-by: Kai-Heng Feng 
Signed-off-by: Greg Kroah-Hartman

USB: Check for dropped connection before switching to full speed

2017-08-16T20:35:31+00:00

commit 94c43b9897abf4ea366ed4dba027494e080c7050 upstream.

Some buggy USB disk adapters disconnect and reconnect multiple times
during the enumeration procedure.  This may lead to a device
connecting at full speed instead of high speed, because when the USB
stack sees that a device isn't able to enumerate at high speed, it
tries to hand the connection over to a full-speed companion
controller.

The logic for doing this is careful to check that the device is still
connected.  But this check is inadequate if the device disconnects and
reconnects before the check is done.  The symptom is that a device
works, but much more slowly than it is capable of operating.

The situation was made worse recently by commit 22547c4cc4fe ("usb:
hub: Wait for connection to be reestablished after port reset"), which
increases the delay following a reset before a disconnect is
recognized, thus giving the device more time to reconnect.

This patch makes the check more robust.  If the device was
disconnected at any time during enumeration, we will now skip the
full-speed handover.

Signed-off-by: Alan Stern 
Reported-and-tested-by: Zdenek Kabelac 
Reviewed-by: Guenter Roeck 
Signed-off-by: Greg Kroah-Hartman

USB: hcd: Mark secondary HCD as dead if the primary one died

2017-08-16T20:35:31+00:00

commit cd5a6a4fdaba150089af2afc220eae0fef74878a upstream.

Make usb_hc_died() clear the HCD_FLAG_RH_RUNNING flag for the shared
HCD and set HCD_FLAG_DEAD for it, in analogy with what is done for
the primary one.

Among other thigs, this prevents check_root_hub_suspended() from
returning -EBUSY for dead HCDs which helps to work around system
suspend issues in some situations.

This actually fixes occasional suspend failures on one of my test
machines.

Suggested-by: Alan Stern 
Signed-off-by: Rafael J. Wysocki 
Acked-by: Alan Stern 
Signed-off-by: Greg Kroah-Hartman

Add USB quirk for HVR-950q to avoid intermittent device resets

2017-07-15T08:14:39+00:00

commit 6836796de4019944f4ba4c99a360e8250fd2e735 upstream.

The USB core and sysfs will attempt to enumerate certain parameters
which are unsupported by the au0828 - causing inconsistent behavior
and sometimes causing the chip to reset.  Avoid making these calls.

This problem manifested as intermittent cases where the au8522 would
be reset on analog video startup, in particular when starting up ALSA
audio streaming in parallel - the sysfs entries created by
snd-usb-audio on streaming startup would result in unsupported control
messages being sent during tuning which would put the chip into an
unknown state.

Signed-off-by: Devin Heitmueller 
Signed-off-by: Greg Kroah-Hartman

usb: core: fix potential memory leak in error path during hcd creation

2017-06-26T05:10:52+00:00

commit 1a744d2eb76aaafb997fda004ae3ae62a1538f85 upstream.

Free memory allocated for address0_mutex if allocation of bandwidth_mutex
failed.

Fixes: feb26ac31a2a ("usb: core: hub: hub_port_init lock controller instead of bus")

Signed-off-by: Anton Bondarenko 
Acked-by: Alan Stern 
Signed-off-by: Greg Kroah-Hartman

USB: hub: fix SS max number of ports

2017-06-26T05:10:51+00:00

commit 93491ced3c87c94b12220dbac0527e1356702179 upstream.

Add define for the maximum number of ports on a SuperSpeed hub as per
USB 3.1 spec Table 10-5, and use it when verifying the retrieved hub
descriptor.

This specifically avoids benign attempts to update the DeviceRemovable
mask for non-existing ports (should we get that far).

Fixes: dbe79bbe9dcb ("USB 3.0 Hub Changes")
Acked-by: Alan Stern 
Signed-off-by: Johan Hovold 
Signed-off-by: Greg Kroah-Hartman

USB: hub: fix non-SS hub-descriptor handling

2017-05-25T12:17:59+00:00

commit bec444cd1c94c48df409a35ad4e5b143c245c3f7 upstream.

Add missing sanity check on the non-SuperSpeed hub-descriptor length in
order to avoid parsing and leaking two bytes of uninitialised slab data
through sysfs removable-attributes (or a compound-device debug
statement).

Note that we only make sure that the DeviceRemovable field is always
present (and specifically ignore the unused PortPwrCtrlMask field) in
order to continue support any hubs with non-compliant descriptors. As a
further safeguard, the descriptor buffer is also cleared.

Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Johan Hovold 
Acked-by: Alan Stern 
Signed-off-by: Greg Kroah-Hartman

USB: hub: fix SS hub-descriptor handling

2017-05-25T12:17:59+00:00

commit 2c25a2c818023df64463aac3288a9f969491e507 upstream.

A SuperSpeed hub descriptor does not have any variable-length fields so
bail out when reading a short descriptor.

This avoids parsing and leaking two bytes of uninitialised slab data
through sysfs removable-attributes.

Fixes: dbe79bbe9dcb ("USB 3.0 Hub Changes")
Cc: John Youn 
Acked-by: Alan Stern 
Signed-off-by: Johan Hovold 
Signed-off-by: Greg Kroah-Hartman

USB: core: replace %p with %pK

2017-05-25T12:17:56+00:00

commit 2f964780c03b73de269b08d12aff96a9618d13f3 upstream.

Format specifier %p can leak kernel addresses while not valuing the
kptr_restrict system settings. When kptr_restrict is set to (1), kernel
pointers printed using the %pK format specifier will be replaced with
Zeros. Debugging Note : &pK prints only Zeros as address. If you need
actual address information, write 0 to kptr_restrict.

echo 0 > /proc/sys/kernel/kptr_restrict

[Found by poking around in a random vendor kernel tree, it would be nice
if someone would actually send these types of patches upstream - gkh]

Signed-off-by: Vamsi Krishna Samavedam 
Signed-off-by: Greg Kroah-Hartman