linux-stable.git/drivers/usb/core, branch v3.18.136

usb: hub: delay hub autosuspend if USB3 port is still link training

2019-02-20T09:08:58+00:00

[ Upstream commit e86108940e541febf35813402ff29fa6f4a9ac0b ]

When initializing a hub we want to give a USB3 port in link training
the same debounce delay time before autosuspening the hub as already
trained, connected enabled ports.

USB3 ports won't reach the enabled state with "current connect status" and
"connect status change" bits set until the USB3 link training finishes.

Catching the port in link training (polling) and adding the debounce delay
prevents unnecessary failed attempts to autosuspend the hub.

Signed-off-by: Mathias Nyman 
Acked-by: Alan Stern 
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Sasha Levin

USB: check usb_get_extra_descriptor for proper size

2018-12-13T08:22:31+00:00

commit 704620afc70cf47abb9d6a1a57f3825d2bca49cf upstream.

When reading an extra descriptor, we need to properly check the minimum
and maximum size allowed, to prevent from invalid data being sent by a
device.

Reported-by: Hui Peng 
Reported-by: Mathias Payer 
Co-developed-by: Linus Torvalds 
Signed-off-by: Hui Peng 
Signed-off-by: Mathias Payer 
Signed-off-by: Linus Torvalds 
Cc: stable 
Signed-off-by: Greg Kroah-Hartman

usb: quirk: add no-LPM quirk on SanDisk Ultra Flair device

2018-12-13T08:22:31+00:00

commit 2f2dde6ba89b1ef1fe23c1138131b315d9aa4019 upstream.

Some lower volume SanDisk Ultra Flair in 16GB, which the VID:PID is
in 0781:5591, will aggressively request LPM of U1/U2 during runtime,
when using this thumb drive as the OS installation key we found the
device will generate failure during U1 exit path making it dropped
from the USB bus, this causes a corrupted installation in system at
the end.

i.e.,
[  166.918296] hub 2-0:1.0: state 7 ports 7 chg 0000 evt 0004
[  166.918327] usb usb2-port2: link state change
[  166.918337] usb usb2-port2: do warm reset
[  166.970039] usb usb2-port2: not warm reset yet, waiting 50ms
[  167.022040] usb usb2-port2: not warm reset yet, waiting 200ms
[  167.276043] usb usb2-port2: status 02c0, change 0041, 5.0 Gb/s
[  167.276050] usb 2-2: USB disconnect, device number 2
[  167.276058] usb 2-2: unregistering device
[  167.276060] usb 2-2: unregistering interface 2-2:1.0
[  167.276170] xhci_hcd 0000:00:15.0: shutdown urb ffffa3c7cc695cc0 ep1in-bulk
[  167.284055] sd 0:0:0:0: [sda] tag#0 FAILED Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
[  167.284064] sd 0:0:0:0: [sda] tag#0 CDB: Read(10) 28 00 00 33 04 90 00 01 00 00
...

Analyzed the USB trace in the link layer we realized it is because
of the 6-ms timer of tRecoveryConfigurationTimeout which documented
on the USB 3.2 Revision 1.0, the section 7.5.10.4.2 of "Exit from
Recovery.Configuration"; device initiates U1 exit -> Recovery.Active
-> Recovery.Configuration, then the host timer timeout makes the link
transits to eSS.Inactive -> Rx.Detect follows by a Warm Reset.

Interestingly, the other higher volume of SanDisk Ultra Flair sharing
the same VID:PID, such as 64GB, would not request LPM during runtime,
it sticks at U0 always, thus disabling LPM does not affect those thumb
drives at all.

The same odd occures in SanDisk Ultra Fit 16GB, VID:PID in 0781:5583.

Signed-off-by: Harry Pan 
Cc: stable 
Signed-off-by: Greg Kroah-Hartman

usb: core: quirks: add RESET_RESUME quirk for Cherry G230 Stream series

2018-12-13T08:22:28+00:00

commit effd14f66cc1ef6701a19c5a56e39c35f4d395a5 upstream.

Cherry G230 Stream 2.0 (G85-231) and 3.0 (G85-232) need this quirk to
function correctly. This fixes a but where double pressing numlock locks
up the device completely with need to replug the keyboard.

Signed-off-by: Michael Niewöhner 
Tested-by: Michael Niewöhner 
Cc: stable 
Signed-off-by: Greg Kroah-Hartman

usb: core: Fix hub port connection events lost

2018-12-01T08:47:58+00:00

commit 22454b79e6de05fa61a2a72d00d2eed798abbb75 upstream.

This will clear the USB_PORT_FEAT_C_CONNECTION bit in case of a hub port reset
only if a device is was attached to the hub port before resetting the hub port.

Using a Lenovo T480s attached to the ultra dock it was not possible to detect
some usb-c devices at the dock usb-c ports because the hub_port_reset code
will clear the USB_PORT_FEAT_C_CONNECTION bit after the actual hub port reset.
Using this device combo the USB_PORT_FEAT_C_CONNECTION bit was set between the
actual hub port reset and the clear of the USB_PORT_FEAT_C_CONNECTION bit.
This ends up with clearing the USB_PORT_FEAT_C_CONNECTION bit after the
new device was attached such that it was not detected.

This patch will not clear the USB_PORT_FEAT_C_CONNECTION bit if there is
currently no device attached to the port before the hub port reset.
This will avoid clearing the connection bit for new attached devices.

Signed-off-by: Dennis Wassenberg 
Acked-by: Mathias Nyman 
Cc: stable 
Signed-off-by: Greg Kroah-Hartman

usb: quirks: Add delay-init quirk for Corsair K70 LUX RGB

2018-11-27T15:05:37+00:00

commit a77112577667cbda7c6292c52d909636aef31fd9 upstream.

Following on from this patch: https://lkml.org/lkml/2017/11/3/516,
Corsair K70 LUX RGB keyboards also require the DELAY_INIT quirk to
start correctly at boot.

Dmesg output:
usb 1-6: string descriptor 0 read error: -110
usb 1-6: New USB device found, idVendor=1b1c, idProduct=1b33
usb 1-6: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 1-6: can't set config #1, error -110

Signed-off-by: Emmanuel Pescosta 
Cc: stable 
Signed-off-by: Greg Kroah-Hartman

USB: quirks: Add no-lpm quirk for Raydium touchscreens

2018-11-27T15:05:37+00:00

commit deefd24228a172d1b27d4a9adbfd2cdacd60ae64 upstream.

Raydium USB touchscreen fails to set config if LPM is enabled:
[    2.030658] usb 1-8: New USB device found, idVendor=2386, idProduct=3119
[    2.030659] usb 1-8: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    2.030660] usb 1-8: Product: Raydium Touch System
[    2.030661] usb 1-8: Manufacturer: Raydium Corporation
[    7.132209] usb 1-8: can't set config #1, error -110

Same behavior can be observed on 2386:3114.

Raydium claims the touchscreen supports LPM under Windows, so I used
Microsoft USB Test Tools (MUTT) [1] to check its LPM status. MUTT shows
that the LPM doesn't work under Windows, either. So let's just disable LPM
for Raydium touchscreens.

[1] https://docs.microsoft.com/en-us/windows-hardware/drivers/usbcon/usb-test-tools

Signed-off-by: Kai-Heng Feng 
Cc: stable 
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Greg Kroah-Hartman

USB: fix the usbfs flag sanitization for control transfers

2018-11-10T15:39:23+00:00

commit 665c365a77fbfeabe52694aedf3446d5f2f1ce42 upstream.

Commit 7a68d9fb8510 ("USB: usbdevfs: sanitize flags more") checks the
transfer flags for URBs submitted from userspace via usbfs.  However,
the check for whether the USBDEVFS_URB_SHORT_NOT_OK flag should be
allowed for a control transfer was added in the wrong place, before
the code has properly determined the direction of the control
transfer.  (Control transfers are special because for them, the
direction is set by the bRequestType byte of the Setup packet rather
than direction bit of the endpoint address.)

This patch moves code which sets up the allow_short flag for control
transfers down after is_in has been set to the correct value.

Signed-off-by: Alan Stern 
Reported-and-tested-by: syzbot+24a30223a4b609bb802e@syzkaller.appspotmail.com
Fixes: 7a68d9fb8510 ("USB: usbdevfs: sanitize flags more")
CC: Oliver Neukum 
CC: 
Signed-off-by: Greg Kroah-Hartman

USB: hub: fix up early-exit pathway in hub_activate

2018-11-10T15:39:21+00:00

[ Upstream commit ca5cbc8b02f9b21cc8cd1ab36668763ec34f9ee8 ]

The early-exit pathway in hub_activate, added by commit e50293ef9775
("USB: fix invalid memory access in hub_activate()") needs
improvement.  It duplicates code that is already present at the end of
the subroutine, and it neglects to undo the effect of a
usb_autopm_get_interface_no_resume() call.

This patch fixes both problems by making the early-exit pathway jump
directly to the end of the subroutine.  It simplifies the code at the
end by merging two conditionals that actually test the same condition
although they appear different: If type < HUB_INIT3 then type must be
either HUB_INIT2 or HUB_INIT, and it can't be HUB_INIT because in that
case the subroutine would have exited earlier.

Signed-off-by: Alan Stern 
CC:  #4.4+
Reviewed-by: Viresh Kumar 
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Sasha Levin

USB: remove LPM management from usb_driver_claim_interface()

2018-10-13T07:09:28+00:00

commit c183813fcee44a249339b7c46e1ad271ca1870aa upstream.

usb_driver_claim_interface() disables and re-enables Link Power
Management, but it shouldn't do either one, for the reasons listed
below.  This patch removes the two LPM-related function calls from the
routine.

The reason for disabling LPM in the analogous function
usb_probe_interface() is so that drivers won't have to deal with
unwanted LPM transitions in their probe routine.  But
usb_driver_claim_interface() doesn't call the driver's probe routine
(or any other callbacks), so that reason doesn't apply here.

Furthermore, no driver other than usbfs will ever call
usb_driver_claim_interface() unless it is already bound to another
interface in the same device, which means disabling LPM here would be
redundant.  usbfs doesn't interact with LPM at all.

Lastly, the error return from usb_unlocked_disable_lpm() isn't handled
properly; the code doesn't clean up its earlier actions before
returning.

Signed-off-by: Alan Stern 
Fixes: 8306095fd2c1 ("USB: Disable USB 3.0 LPM in critical sections.")
CC: 
Signed-off-by: Greg Kroah-Hartman