linux-stable.git/drivers/usb/core, branch v3.12.28

USB: Fix persist resume of some SS USB devices

2014-09-03T19:31:15+00:00

commit a40178b2fa6ad87670fb1e5fa4024db00c149629 upstream.

Problem Summary: Problem has been observed generally with PM states
where VBUS goes off during suspend. There are some SS USB devices which
take longer time for link training compared to many others.  Such
devices fail to reconnect with same old address which was associated
with it before suspend.

When system resumes, at some point of time (dpm_run_callback->
usb_dev_resume->usb_resume->usb_resume_both->usb_resume_device->
usb_port_resume) SW reads hub status. If device is present,
then it finishes port resume and re-enumerates device with same
address. If device is not present then, SW thinks that device was
removed during suspend and therefore does logical disconnection
and removes all the resource allocated for this device.

Now, if I put sufficient delay just before root hub status read in
usb_resume_device then, SW sees always that device is present. In normal
course(without any delay) SW sees that no device is present and then SW
removes all resource associated with the device at this port.  In the
latter case, after sometime, device says that hey I am here, now host
enumerates it, but with new address.

Problem had been reproduced when I connect verbatim USB3.0 hard disc
with my STiH407 XHCI host running with 3.10 kernel.

I see that similar problem has been reported here.
https://bugzilla.kernel.org/show_bug.cgi?id=53211
Reading above it seems that bug was not in 3.6.6 and was present in 3.8
and again it was not present for some in 3.12.6, while it was present
for few others. I tested with 3.13-FC19 running at i686 desktop, problem
was still there. However, I was failed to reproduce it with 3.16-RC4
running at same i686 machine. I would say it is just a random
observation. Problem for few devices is always there, as I am unable to
find a proper fix for the issue.

So, now question is what should be the amount of delay so that host is
always able to recognize suspended device after resume.

XHCI specs 4.19.4 says that when Link training is successful, port sets
CSC bit to 1. So if SW reads port status before successful link
training, then it will not find device to be present.  USB Analyzer log
with such buggy devices show that in some cases device switch on the
RX termination after long delay of host enabling the VBUS. In few other
cases it has been seen that device fails to negotiate link training in
first attempt. It has been reported till now that few devices take as
long as 2000 ms to train the link after host enabling its VBUS and
RX termination. This patch implements a 2000 ms timeout for CSC bit to set
ie for link training. If in a case link trains before timeout, loop will
exit earlier.

This patch implements above delay, but only for SS device and when
persist is enabled.

So, for the good device overhead is almost none. While for the bad
devices penalty could be the time which it take for link training.
But, If a device was connected before suspend, and was removed
while system was asleep, then the penalty would be the timeout ie
2000 ms.

Results:

Verbatim USB SS hard disk connected with STiH407 USB host running 3.10
Kernel resumes in 461 msecs without this patch, but hard disk is
assigned a new device address. Same system resumes in 790 msecs with
this patch, but with old device address.

Signed-off-by: Pratyush Anand 
Acked-by: Alan Stern 
Signed-off-by: Jiri Slaby

USB: devio: fix issue with log flooding

2014-09-03T19:31:13+00:00

commit d310d05f1225d1f6f2bf505255fdf593bfbb3051 upstream.

usbfs allows user space to pass down an URB which sets URB_SHORT_NOT_OK
for output URBs. That causes usbcore to log messages without limit
for a nonsensical disallowed combination. The fix is to silently drop
the attribute in usbfs.
The problem is reported to exist since 3.14
https://www.virtualbox.org/ticket/13085

Signed-off-by: Oliver Neukum 
Acked-by: Alan Stern 
Signed-off-by: Jiri Slaby

USB: core: hcd-pci: free IRQ before disabling PCI device when shutting down

2014-09-02T09:37:58+00:00

commit c5946f9d286ad368329c79107fdf4d825d2091bd upstream.

The assigned IRQ should be freed before calling pci_disable_device()
when shutting down system, otherwise it will cause following warning.
[  568.879482] ------------[ cut here ]------------
[  568.884236] WARNING: CPU: 1 PID: 3300 at /home/konrad/ssd/konrad/xtt-i386/bootstrap/linux-usb/fs/proc/generic.c:521 remove_proc_entry+0x165/0x170()
[  568.897846] remove_proc_entry: removing non-empty directory 'irq/16', leaking at least 'ohci_hcd:usb4'
[  568.907430] Modules linked in: dm_multipath dm_mod iscsi_boot_sysfs iscsi_tcp libiscsi_tcp libiscsi scsi_transport_iscsi libcrc32c crc32c_generic sg sd_mod crct10dif_generic crc_t10dif crct10dif_common radeon fbcon tileblit ttm font bitblit softcursor ata_generic ahci libahci drm_kms_helper skge r8169 libata mii scsi_mod wmi acpi_cpufreq
[  568.938539] CPU: 1 PID: 3300 Comm: init Tainted: G        W     3.16.0-rc5upstream-01651-g03b9189 #1
[  568.947946] Hardware name: ECS A780GM-A Ultra/A780GM-A Ultra, BIOS 080015  04/01/2010
[  568.956008]  00000209 ed0f1cd0 c1617946 c175403c ed0f1d00 c1090c3f c1754084 ed0f1d2c
[  568.964068]  00000ce4 c175403c 00000209 c11f22a5 c11f22a5 f755e8c0 ed0f1d78 f755e90d
[  568.972128]  ed0f1d18 c1090cde 00000009 ed0f1d10 c1754084 ed0f1d2c ed0f1d60 c11f22a5
[  568.980194] Call Trace:
[  568.982715]  [] dump_stack+0x48/0x60
[  568.987294]  [] warn_slowpath_common+0x7f/0xa0
[  569.003887]  [] warn_slowpath_fmt+0x2e/0x30
[  569.009092]  [] remove_proc_entry+0x165/0x170
[  569.014476]  [] unregister_irq_proc+0xaa/0xc0
[  569.019858]  [] free_desc+0x1f/0x60
[  569.024346]  [] irq_free_descs+0x3a/0x80
[  569.029283]  [] irq_dispose_mapping+0x2d/0x50
[  569.034666]  [] mp_unmap_irq+0x73/0xa0
[  569.039423]  [] acpi_unregister_gsi_ioapic+0x2b/0x40
[  569.045431]  [] acpi_unregister_gsi+0xf/0x20
[  569.050725]  [] acpi_pci_irq_disable+0x4b/0x50
[  569.056196]  [] pcibios_disable_device+0x18/0x20
[  569.061848]  [] do_pci_disable_device+0x4d/0x60
[  569.067410]  [] pci_disable_device+0x47/0xb0
[  569.077814]  [] usb_hcd_pci_shutdown+0x31/0x40
[  569.083285]  [] pci_device_shutdown+0x19/0x50
[  569.088667]  [] device_shutdown+0x14/0x120
[  569.093777]  [] kernel_restart_prepare+0x2d/0x30
[  569.099429]  [] kernel_restart+0xe/0x60
[  569.109028]  [] SYSC_reboot+0x191/0x220
[  569.159269]  [] SyS_reboot+0x1a/0x20
[  569.163843]  [] sysenter_do_call+0x12/0x16
[  569.168951] ---[ end trace ccc1ec4471c289c9 ]---

Tested-by: Aaron Lu 
Signed-off-by: Jiang Liu 
Reviewed-by: Huang Rui 
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Jiri Slaby

usb-core bInterval quirk

2014-09-02T09:37:54+00:00

commit cd83ce9e6195aa3ea15ab4db92892802c20df5d0 upstream.

This patch adds a usb quirk to support devices with interupt endpoints
and bInterval values expressed as microframes. The quirk causes the
parse endpoint function to modify the reported bInterval to a standards
conforming value.

There is currently code in the endpoint parser that checks for
bIntervals that are outside of the valid range (1-16 for USB 2+ high
speed and super speed interupt endpoints). In this case, the code assumes
the bInterval is being reported in 1ms frames. As well, the correction
is only applied if the original bInterval value is out of the 1-16 range.

With this quirk applied to the device, the bInterval will be
accurately adjusted from microframes to an exponent.

Signed-off-by: James P Michels III 
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Jiri Slaby

USB: add reset resume quirk for usb3503

2014-09-02T09:22:46+00:00

commit 526a4045c60fbaede88ec95a69a73059dff02160 upstream.

The usb device will autoresume from choose_wakeup() if it is
autosuspended with the wrong wakeup setting, but below errors occur
because usb3503 misc driver will switch to standby mode when suspended.

As add USB_QUIRK_RESET_RESUME, it can stop setting wrong wakeup from
autosuspend_check().

[    7.734717] usb 1-3: reset high-speed USB device number 3 using exynos-ehci
[    7.854658] usb 1-3: device descriptor read/64, error -71
[    8.079657] usb 1-3: device descriptor read/64, error -71
[    8.294664] usb 1-3: reset high-speed USB device number 3 using exynos-ehci
[    8.414658] usb 1-3: device descriptor read/64, error -71
[    8.639657] usb 1-3: device descriptor read/64, error -71
[    8.854667] usb 1-3: reset high-speed USB device number 3 using exynos-ehci
[    9.264598] usb 1-3: device not accepting address 3, error -71
[    9.374655] usb 1-3: reset high-speed USB device number 3 using exynos-ehci
[    9.784601] usb 1-3: device not accepting address 3, error -71
[    9.784838] usb usb1-port3: device 1-3 not suspended yet

Signed-off-by: Joonyoung Shim 
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Jiri Slaby

usb: Check if port status is equal to RxDetect

2014-07-29T14:45:41+00:00

commit bb86cf569bbd7ad4dce581a37c7fbd748057e9dc upstream.

When using USB 3.0 pen drive with the [AMD] FCH USB XHCI Controller
[1022:7814], the second hotplugging will experience the USB 3.0 pen
drive is recognized as high-speed device. After bisecting the kernel,
I found the commit number 41e7e056cdc662f704fa9262e5c6e213b4ab45dd
(USB: Allow USB 3.0 ports to be disabled.) causes the bug. After doing
some experiments, the bug can be fixed by avoiding executing the function
hub_usb3_port_disable(). Because the port status with [AMD] FCH USB
XHCI Controlleris [1022:7814] is already in RxDetect
(I tried printing out the port status before setting to Disabled state),
it's reasonable to check the port status before really executing
hub_usb3_port_disable().

Fixes: 41e7e056cdc6 (USB: Allow USB 3.0 ports to be disabled.)
Signed-off-by: Gavin Guo 
Acked-by: Alan Stern 
Signed-off-by: Jiri Slaby

USB: Avoid runtime suspend loops for HCDs that can't handle suspend/resume

2014-06-20T15:34:11+00:00

commit 8ef42ddd9a53b73e6fc3934278710c27f80f324f upstream.

Not all host controller drivers have bus-suspend and bus-resume
methods.  When one doesn't, it will cause problems if runtime PM is
enabled in the kernel.  The PM core will attempt to suspend the
controller's root hub, the suspend will fail because there is no
bus-suspend routine, and a -EBUSY error code will be returned to the
PM core.  This will cause the suspend attempt to be repeated shortly
thereafter, in a never-ending loop.

Part of the problem is that the original error code -ENOENT gets
changed to -EBUSY in usb_runtime_suspend(), on the grounds that the PM
core will interpret -ENOENT as meaning that the root hub has gotten
into a runtime-PM error state.  While this change is appropriate for
real USB devices, it's not such a good idea for a root hub.  In fact,
considering the root hub to be in a runtime-PM error state would not
be far from the truth.  Therefore this patch updates
usb_runtime_suspend() so that it adjusts error codes only for
non-root-hub devices.

Furthermore, the patch attempts to prevent the problem from occurring
in the first place by not enabling runtime PM by default for root hubs
whose host controller driver doesn't have bus_suspend and bus_resume
methods.

Signed-off-by: Alan Stern 
Reported-by: Will Deacon 
Tested-by: Will Deacon 
Signed-off-by: Jiri Slaby

USB: unbind all interfaces before rebinding any

2014-05-15T07:55:34+00:00

commit 6aec044cc2f5670cf3b143c151c8be846499bd15 upstream.

When a driver doesn't have pre_reset, post_reset, or reset_resume
methods, the USB core unbinds that driver when its device undergoes a
reset or a reset-resume, and then rebinds it afterward.

The existing straightforward implementation can lead to problems,
because each interface gets unbound and rebound before the next
interface is handled.  If a driver claims additional interfaces, the
claim may fail because the old binding instance may still own the
additional interface when the new instance tries to claim it.

This patch fixes the problem by first unbinding all the interfaces
that are marked (i.e., their needs_binding flag is set) and then
rebinding all of them.

The patch also makes the helper functions in driver.c a little more
uniform and adjusts some out-of-date comments.

Signed-off-by: Alan Stern 
Reported-and-tested-by: "Poulain, Loic" 
Signed-off-by: Jiri Slaby

USB: fix crash during hotplug of PCI USB controller card

2014-05-15T07:55:03+00:00

commit a2ff864b53eac9a0e9b05bfe9d1781ccd6c2af71 upstream.

The code in hcd-pci.c that matches up EHCI controllers with their
companion UHCI or OHCI controllers assumes that the private drvdata
fields don't get set too early.  However, it turns out that this field
gets set by usb_create_hcd(), before hcd-pci expects it, and this can
result in a crash when two controllers are probed in parallel (as can
happen when a new controller card is hotplugged).

The companions_rwsem lock was supposed to prevent this sort of thing,
but usb_create_hcd() is called outside the scope of the rwsem.

A simple solution is to check that the root-hub pointer has been
initialized as well as the drvdata field.  This doesn't happen until
usb_add_hcd() is called; that call and the check are both protected by
the rwsem.

This patch should be applied to stable kernels from 3.10 onward.

Signed-off-by: Alan Stern 
Reported-by: Stefani Seibold 
Tested-by: Stefani Seibold 
Signed-off-by: Jiri Slaby

usb: Make DELAY_INIT quirk wait 100ms between Get Configuration requests

2014-03-22T21:01:54+00:00

commit d86db25e53fa69e3e97f3b55dd82a70689787c5d upstream.

The DELAY_INIT quirk only reduces the frequency of enumeration failures
with the Logitech HD Pro C920 and C930e webcams, but does not quite
eliminate them. We have found that adding a delay of 100ms between the
first and second Get Configuration request makes the device enumerate
perfectly reliable even after several weeks of extensive testing. The
reasons for that are anyone's guess, but since the DELAY_INIT quirk
already delays enumeration by a whole second, wating for another 10th of
that isn't really a big deal for the one other device that uses it, and
it will resolve the problems with these webcams.

Signed-off-by: Julius Werner 
Signed-off-by: Jiri Slaby