commit ff712188daa3fe3ce7e11e530b4dca3826dae14a upstream. When used on Huawei hisi platforms, Prolific Mass Storage Card Reader which the VID:PID is in 067b:2731 might fail to enumerate at boot time and doesn't work well with LPM enabled, combination quirks: USB_QUIRK_DELAY_INIT + USB_QUIRK_NO_LPM fixed the problems. Signed-off-by: Miao Li <limiao@kylinos.cn> Cc: stable <stable@kernel.org> Link: https://lore.kernel.org/r/20250304070757.139473-1-limiao870622@163.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2b66ef84d0d2a0ea955b40bd306f5e3abbc5cf9c upstream.
The xHC resources allocated for USB devices are not released in correct
order after resuming in case when while suspend device was reconnected.
This issue has been detected during the fallowing scenario:
- connect hub HS to root port
- connect LS/FS device to hub port
- wait for enumeration to finish
- force host to suspend
- reconnect hub attached to root port
- wake host
For this scenario during enumeration of USB LS/FS device the Cadence xHC
reports completion error code for xHC commands because the xHC resources
used for devices has not been properly released.
XHCI specification doesn't mention that device can be reset in any order
so, we should not treat this issue as Cadence xHC controller bug.
Similar as during disconnecting in this case the device resources should
be cleared starting form the last usb device in tree toward the root hub.
To fix this issue usbcore driver should call hcd->driver->reset_device
for all USB devices connected to hub which was reconnected while
suspending.
Fixes: 3d82904559f4 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/PH7PR07MB953841E38C088678ACDCF6EEDDCC2@PH7PR07MB9538.namprd07.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2240fed37afbcdb5e8b627bc7ad986891100e05d upstream. Robert Morris created a test program which can cause usb_hub_to_struct_hub() to dereference a NULL or inappropriate pointer: Oops: general protection fault, probably for non-canonical address 0xcccccccccccccccc: 0000 [#1] SMP DEBUG_PAGEALLOC PTI CPU: 7 UID: 0 PID: 117 Comm: kworker/7:1 Not tainted 6.13.0-rc3-00017-gf44d154d6e3d #14 Hardware name: FreeBSD BHYVE/BHYVE, BIOS 14.0 10/17/2021 Workqueue: usb_hub_wq hub_event RIP: 0010:usb_hub_adjust_deviceremovable+0x78/0x110 ... Call Trace: <TASK> ? die_addr+0x31/0x80 ? exc_general_protection+0x1b4/0x3c0 ? asm_exc_general_protection+0x26/0x30 ? usb_hub_adjust_deviceremovable+0x78/0x110 hub_probe+0x7c7/0xab0 usb_probe_interface+0x14b/0x350 really_probe+0xd0/0x2d0 ? __pfx___device_attach_driver+0x10/0x10 __driver_probe_device+0x6e/0x110 driver_probe_device+0x1a/0x90 __device_attach_driver+0x7e/0xc0 bus_for_each_drv+0x7f/0xd0 __device_attach+0xaa/0x1a0 bus_probe_device+0x8b/0xa0 device_add+0x62e/0x810 usb_set_configuration+0x65d/0x990 usb_generic_driver_probe+0x4b/0x70 usb_probe_device+0x36/0xd0 The cause of this error is that the device has two interfaces, and the hub driver binds to interface 1 instead of interface 0, which is where usb_hub_to_struct_hub() looks. We can prevent the problem from occurring by refusing to accept hub devices that violate the USB spec by having more than one configuration or interface. Reported-and-tested-by: Robert Morris <rtm@csail.mit.edu> Cc: stable <stable@kernel.org> Closes: https://lore.kernel.org/linux-usb/95564.1737394039@localhost/ Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Link: https://lore.kernel.org/r/c27f3bf4-63d8-4fb5-ac82-09e3cd19f61c@rowland.harvard.edu Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 159daf1258227f44b26b5d38f4aa8f37b8cca663 upstream.
The fastboot tool for communicating with Android bootloaders does not
work reliably with this device if USB 2 Link Power Management (LPM)
is enabled.
Various fastboot commands are affected, including the
following, which usually reproduces the problem within two tries:
fastboot getvar kernel
getvar:kernel FAILED (remote: 'GetVar Variable Not found')
This issue was hidden on many systems up until commit 63a1f8454962
("xhci: stored cached port capability values in one place") as the xhci
driver failed to detect USB 2 LPM support if USB 3 ports were listed
before USB 2 ports in the "supported protocol capabilities".
Adding the quirk resolves the issue. No drawbacks are expected since
the device uses different USB product IDs outside of fastboot mode, and
since fastboot commands worked before, until LPM was enabled on the
tested system by the aforementioned commit.
Based on a patch from Forest <forestix@nom.one> from which most of the
code and commit message is taken.
Cc: stable <stable@kernel.org>
Reported-by: Forest <forestix@nom.one>
Closes: https://lore.kernel.org/hk8umj9lv4l4qguftdq1luqtdrpa1gks5l@sonic.net
Tested-by: Forest <forestix@nom.one>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250206151836.51742-1-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e169d96eecd447ff7fd7542ca5fa0911f5622054 upstream. Teclast disk used on Huawei hisi platforms doesn't work well, losing connectivity intermittently if LPM is enabled. Add quirk disable LPM to resolve the issue. Signed-off-by: Lei Huang <huanglei@kylinos.cn> Cc: stable <stable@kernel.org> Link: https://lore.kernel.org/r/20250212093829.7379-1-huanglei814@163.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4aac0db5a0ebc599d4ad9bf5ebab78afa1f33e10 upstream.
When usb_control_msg is used in the get_bMaxPacketSize0 function, the
USB pipe does not include the endpoint device number. This can cause
failures when a usb hub port is reinitialized after encountering a bad
cable connection. As a result, the system logs the following error
messages:
usb usb2-port1: cannot reset (err = -32)
usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
usb usb2-port1: attempt power cycle
usb 2-1: new high-speed USB device number 5 using ci_hdrc
usb 2-1: device descriptor read/8, error -71
The problem began after commit 85d07c556216 ("USB: core: Unite old
scheme and new scheme descriptor reads"). There
usb_get_device_descriptor was replaced with get_bMaxPacketSize0. Unlike
usb_get_device_descriptor, the get_bMaxPacketSize0 function uses the
macro usb_rcvaddr0pipe, which does not include the endpoint device
number. usb_get_device_descriptor, on the other hand, used the macro
usb_rcvctrlpipe, which includes the endpoint device number.
By modifying the get_bMaxPacketSize0 function to use usb_rcvctrlpipe
instead of usb_rcvaddr0pipe, the issue can be resolved. This change will
ensure that the endpoint device number is included in the USB pipe,
preventing reinitialization failures. If the endpoint has not set the
device number yet, it will still work because the device number is 0 in
udev.
Cc: stable <stable@kernel.org>
Fixes: 85d07c556216 ("USB: core: Unite old scheme and new scheme descriptor reads")
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20250203105840.17539-1-eichest@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's USB error when tegra board is shutting down:
[ 180.919315] usb 2-3: Failed to set U1 timeout to 0x0,error code -113
[ 180.919995] usb 2-3: Failed to set U1 timeout to 0xa,error code -113
[ 180.920512] usb 2-3: Failed to set U2 timeout to 0x4,error code -113
[ 186.157172] tegra-xusb 3610000.usb: xHCI host controller not responding, assume dead
[ 186.157858] tegra-xusb 3610000.usb: HC died; cleaning up
[ 186.317280] tegra-xusb 3610000.usb: Timeout while waiting for evaluate context command
The issue is caused by disabling LPM on already suspended ports.
For USB2 LPM, the LPM is already disabled during port suspend. For USB3
LPM, port won't transit to U1/U2 when it's already suspended in U3,
hence disabling LPM is only needed for ports that are not suspended.
Cc: Wayne Chang <waynec@nvidia.com>
Cc: stable <stable@kernel.org>
Fixes: d920a2ed8620 ("usb: Disable USB3 LPM at shutdown")
Signed-off-by: Kai-Heng Feng <kaihengf@nvidia.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20241206074817.89189-1-kaihengf@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When device_add(&udev->dev) succeeds and a later call fails,
usb_new_device() does not properly call device_del(). As comment of
device_add() says, 'if device_add() succeeds, you should call
device_del() when you want to get rid of it. If device_add() has not
succeeded, use only put_device() to drop the reference count'.
Found by code review.
Cc: stable <stable@kernel.org>
Fixes: 9f8b17e643fe ("USB: make usbdevices export their device nodes instead of using a separate class")
Signed-off-by: Ma Ke <make_ruc2021@163.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20241218071346.2973980-1-make_ruc2021@163.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Before commit 53a2d95df836 ("usb: core: add phy notify connect and
disconnect"), phy initialization will be skipped even when shared hcd
doesn't set skip_phy_initialization flag. However, the situation is
changed after the commit. The hcd.c will initialize phy when add shared
hcd. This behavior is unexpected for some platforms which will handle phy
initialization by themselves. To avoid the issue, this will only check
skip_phy_initialization flag of primary hcd since shared hcd normally
follow primary hcd setting.
Fixes: 53a2d95df836 ("usb: core: add phy notify connect and disconnect")
Cc: stable@vger.kernel.org
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://lore.kernel.org/r/20241105090120.2438366-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull driver core updates from Greg KH:
"Here is a small set of driver core changes for 6.13-rc1.
Nothing major for this merge cycle, except for the two simple merge
conflicts are here just to make life interesting.
Included in here are:
- sysfs core changes and preparations for more sysfs api cleanups
that can come through all driver trees after -rc1 is out
- fw_devlink fixes based on many reports and debugging sessions
- list_for_each_reverse() removal, no one was using it!
- last-minute seq_printf() format string bug found and fixed in many
drivers all at once.
- minor bugfixes and changes full details in the shortlog"
* tag 'driver-core-6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (35 commits)
Fix a potential abuse of seq_printf() format string in drivers
cpu: Remove spurious NULL in attribute_group definition
s390/con3215: Remove spurious NULL in attribute_group definition
perf: arm-ni: Remove spurious NULL in attribute_group definition
driver core: Constify bin_attribute definitions
sysfs: attribute_group: allow registration of const bin_attribute
firmware_loader: Fix possible resource leak in fw_log_firmware_info()
drivers: core: fw_devlink: Fix excess parameter description in docstring
driver core: class: Correct WARN() message in APIs class_(for_each|find)_device()
cacheinfo: Use of_property_present() for non-boolean properties
cdx: Fix cdx_mmap_resource() after constifying attr in ->mmap()
drivers: core: fw_devlink: Make the error message a bit more useful
phy: tegra: xusb: Set fwnode for xusb port devices
drm: display: Set fwnode for aux bus devices
driver core: fw_devlink: Stop trying to optimize cycle detection logic
driver core: Constify attribute arguments of binary attributes
sysfs: bin_attribute: add const read/write callback variants
sysfs: implement all BIN_ATTR_* macros in terms of __BIN_ATTR()
sysfs: treewide: constify attribute callback of bin_attribute::llseek()
sysfs: treewide: constify attribute callback of bin_attribute::mmap()
...