linux-stable.git/drivers/usb/core, branch linux-5.0.y

usb: core: Add PM runtime calls to usb_hcd_platform_shutdown

2019-05-31T13:45:16+00:00

[ Upstream commit 8ead7e817224d7832fe51a19783cb8fcadc79467 ]

If ohci-platform is runtime suspended, we can currently get an "imprecise
external abort" on reboot with ohci-platform loaded when PM runtime
is implemented for the SoC.

Let's fix this by adding PM runtime support to usb_hcd_platform_shutdown.

Signed-off-by: Tony Lindgren 
Acked-by: Alan Stern 
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Sasha Levin

USB: core: Don't unbind interfaces following device reset failure

2019-05-31T13:45:04+00:00

[ Upstream commit 381419fa720060ba48b7bbc483be787d5b1dca6f ]

The SCSI core does not like to have devices or hosts unregistered
while error recovery is in progress.  Trying to do so can lead to
self-deadlock: Part of the removal code tries to obtain a lock already
held by the error handler.

This can cause problems for the usb-storage and uas drivers, because
their error handler routines perform a USB reset, and if the reset
fails then the USB core automatically goes on to unbind all drivers
from the device's interfaces -- all while still in the context of the
SCSI error handler.

As it turns out, practically all the scenarios leading to a USB reset
failure end up causing a device disconnect (the main error pathway in
usb_reset_and_verify_device(), at the end of the routine, calls
hub_port_logical_disconnect() before returning).  As a result, the
hub_wq thread will soon become aware of the problem and will unbind
all the device's drivers in its own context, not in the
error-handler's context.

This means that usb_reset_device() does not need to call
usb_unbind_and_rebind_marked_interfaces() in cases where
usb_reset_and_verify_device() has returned an error, because hub_wq
will take care of everything anyway.

This particular problem was observed in somewhat artificial
circumstances, by using usbfs to tell a hub to power-down a port
connected to a USB-3 mass storage device using the UAS protocol.  With
the port turned off, the currently executing command timed out and the
error handler started running.  The USB reset naturally failed,
because the hub port was off, and the error handler deadlocked as
described above.  Not carrying out the call to
usb_unbind_and_rebind_marked_interfaces() fixes this issue.

Signed-off-by: Alan Stern 
Reported-by: Kento Kobayashi 
Tested-by: Kento Kobayashi 
CC: Bart Van Assche 
CC: Martin K. Petersen 
CC: Jacky Cao 
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Sasha Levin

USB: core: Fix bug caused by duplicate interface PM usage counter

2019-05-08T05:22:45+00:00

commit c2b71462d294cf517a0bc6e4fd6424d7cee5596f upstream.

The syzkaller fuzzer reported a bug in the USB hub driver which turned
out to be caused by a negative runtime-PM usage counter.  This allowed
a hub to be runtime suspended at a time when the driver did not expect
it.  The symptom is a WARNING issued because the hub's status URB is
submitted while it is already active:

	URB 0000000031fb463e submitted while active
	WARNING: CPU: 0 PID: 2917 at drivers/usb/core/urb.c:363

The negative runtime-PM usage count was caused by an unfortunate
design decision made when runtime PM was first implemented for USB.
At that time, USB class drivers were allowed to unbind from their
interfaces without balancing the usage counter (i.e., leaving it with
a positive count).  The core code would take care of setting the
counter back to 0 before allowing another driver to bind to the
interface.

Later on when runtime PM was implemented for the entire kernel, the
opposite decision was made: Drivers were required to balance their
runtime-PM get and put calls.  In order to maintain backward
compatibility, however, the USB subsystem adapted to the new
implementation by keeping an independent usage counter for each
interface and using it to automatically adjust the normal usage
counter back to 0 whenever a driver was unbound.

This approach involves duplicating information, but what is worse, it
doesn't work properly in cases where a USB class driver delays
decrementing the usage counter until after the driver's disconnect()
routine has returned and the counter has been adjusted back to 0.
Doing so would cause the usage counter to become negative.  There's
even a warning about this in the USB power management documentation!

As it happens, this is exactly what the hub driver does.  The
kick_hub_wq() routine increments the runtime-PM usage counter, and the
corresponding decrement is carried out by hub_event() in the context
of the hub_wq work-queue thread.  This work routine may sometimes run
after the driver has been unbound from its interface, and when it does
it causes the usage counter to go negative.

It is not possible for hub_disconnect() to wait for a pending
hub_event() call to finish, because hub_disconnect() is called with
the device lock held and hub_event() acquires that lock.  The only
feasible fix is to reverse the original design decision: remove the
duplicate interface-specific usage counter and require USB drivers to
balance their runtime PM gets and puts.  As far as I know, all
existing drivers currently do this.

Signed-off-by: Alan Stern 
Reported-and-tested-by: syzbot+7634edaea4d0b341c625@syzkaller.appspotmail.com
CC: 
Signed-off-by: Greg Kroah-Hartman

USB: core: Fix unterminated string returned by usb_string()

2019-05-08T05:22:45+00:00

commit c01c348ecdc66085e44912c97368809612231520 upstream.

Some drivers (such as the vub300 MMC driver) expect usb_string() to
return a properly NUL-terminated string, even when an error occurs.
(In fact, vub300's probe routine doesn't bother to check the return
code from usb_string().)  When the driver goes on to use an
unterminated string, it leads to kernel errors such as
stack-out-of-bounds, as found by the syzkaller USB fuzzer.

An out-of-range string index argument is not at all unlikely, given
that some devices don't provide string descriptors and therefore list
0 as the value for their string indexes.  This patch makes
usb_string() return a properly terminated empty string along with the
-EINVAL error code when an out-of-range index is encountered.

And since a USB string index is a single-byte value, indexes >= 256
are just as invalid as values of 0 or below.

Signed-off-by: Alan Stern 
Reported-by: syzbot+b75b85111c10b8d680f1@syzkaller.appspotmail.com
CC: 
Signed-off-by: Greg Kroah-Hartman

USB: Consolidate LPM checks to avoid enabling LPM twice

2019-05-02T08:02:48+00:00

commit d7a6c0ce8d26412903c7981503bad9e1cc7c45d2 upstream.

USB Bluetooth controller QCA ROME (0cf3:e007) sometimes stops working
after S3:
[ 165.110742] Bluetooth: hci0: using NVM file: qca/nvm_usb_00000302.bin
[ 168.432065] Bluetooth: hci0: Failed to send body at 4 of 1953 (-110)

After some experiments, I found that disabling LPM can workaround the
issue.

On some platforms, the USB power is cut during S3, so the driver uses
reset-resume to resume the device. During port resume, LPM gets enabled
twice, by usb_reset_and_verify_device() and usb_port_resume().

Consolidate all checks into new LPM helpers to make sure LPM only gets
enabled once.

Fixes: de68bab4fa96 ("usb: Don't enable USB 2.0 Link PM by default.”)
Signed-off-by: Kai-Heng Feng 
Cc: stable  # after much soaking
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Greg Kroah-Hartman

USB: Add new USB LPM helpers

2019-05-02T08:02:48+00:00

commit 7529b2574a7aaf902f1f8159fbc2a7caa74be559 upstream.

Use new helpers to make LPM enabling/disabling more clear.

This is a preparation to subsequent patch.

Signed-off-by: Kai-Heng Feng 
Cc: stable  # after much soaking
Signed-off-by: Greg Kroah-Hartman

USB: leds: fix regression in usbport led trigger

2019-01-18T08:55:05+00:00

The patch "usb: simplify usbport trigger" together with "leds: triggers:
add device attribute support" caused an regression for the usbport
trigger. it will no longer enumerate any active usb hub ports under the
"ports" directory in the sysfs class directory, if the usb host drivers
are fully initialized before the usbport trigger was loaded.

The reason is that the usbport driver tries to register the sysfs
entries during the activate() callback. And this will fail with -2 /
ENOENT because the patch "leds: triggers: add device attribute support"
made it so that the sysfs "ports" group was only being added after the
activate() callback succeeded.

This version of the patch reverts parts of the "usb: simplify usbport
trigger" patch and restores usbport trigger's functionality.

Fixes: 6f7b0bad8839 ("usb: simplify usbport trigger")
Signed-off-by: Christian Lamparter 
Cc: stable 
Acked-by: Jacek Anaszewski 
Signed-off-by: Greg Kroah-Hartman

USB: Add USB_QUIRK_DELAY_CTRL_MSG quirk for Corsair K70 RGB

2019-01-07T16:29:28+00:00

To match the Corsair Strafe RGB, the Corsair K70 RGB also requires
USB_QUIRK_DELAY_CTRL_MSG to completely resolve boot connection issues
discussed here: https://github.com/ckb-next/ckb-next/issues/42.
Otherwise roughly 1 in 10 boots the keyboard will fail to be detected.

Patch that applied delay control quirk for Corsair Strafe RGB:
cb88a0588717 ("usb: quirks: add control message delay for 1b1c:1b20")

Previous K70 RGB patch to add delay-init quirk:
7a1646d92257 ("Add delay-init quirk for Corsair K70 RGB keyboards")

Signed-off-by: Jack Stocker 
Cc: stable 
Signed-off-by: Greg Kroah-Hartman

usbcore: Select only first configuration for non-UAC3 compliant devices

2019-01-07T16:23:30+00:00

In most of the UAC1 and UAC2 audio devices, the first
configuration is most often the best configuration.
However, with recent patch to support UAC3 configuration,
second configuration was unintentionally chosen for
some of the UAC1/2 devices that had more than one
configuration. This was because of the existing check
after the audio config check which selected any config
which had a non-vendor class. This patch fixes this issue.

Fixes: f13912d3f014 ("usbcore: Select UAC3 configuration for audio if present")
Reported-by: Con Kolivas 
Signed-off-by: Saranya Gopal 
Tested-by: Con Kolivas 
Cc: stable 
Signed-off-by: Greg Kroah-Hartman

Remove 'type' argument from access_ok() function

2019-01-04T02:57:57+00:00

Nobody has actually used the type (VERIFY_READ vs VERIFY_WRITE) argument
of the user address range verification function since we got rid of the
old racy i386-only code to walk page tables by hand.

It existed because the original 80386 would not honor the write protect
bit when in kernel mode, so you had to do COW by hand before doing any
user access.  But we haven't supported that in a long time, and these
days the 'type' argument is a purely historical artifact.

A discussion about extending 'user_access_begin()' to do the range
checking resulted this patch, because there is no way we're going to
move the old VERIFY_xyz interface to that model.  And it's best done at
the end of the merge window when I've done most of my merges, so let's
just get this done once and for all.

This patch was mostly done with a sed-script, with manual fix-ups for
the cases that weren't of the trivial 'access_ok(VERIFY_xyz' form.

There were a couple of notable cases:

 - csky still had the old "verify_area()" name as an alias.

 - the iter_iov code had magical hardcoded knowledge of the actual
   values of VERIFY_{READ,WRITE} (not that they mattered, since nothing
   really used it)

 - microblaze used the type argument for a debug printout

but other than those oddities this should be a total no-op patch.

I tried to fix up all architectures, did fairly extensive grepping for
access_ok() uses, and the changes are trivial, but I may have missed
something.  Any missed conversion should be trivially fixable, though.

Signed-off-by: Linus Torvalds