linux-stable.git/drivers/usb/core, branch linux-4.10.y

usb: hub: Do not attempt to autosuspend disconnected devices

2017-05-20T12:30:57+00:00

commit f5cccf49428447dfbc9edb7a04bb8fc316269781 upstream.

While running a bind/unbind stress test with the dwc3 usb driver on rk3399,
the following crash was observed.

Unable to handle kernel NULL pointer dereference at virtual address 00000218
pgd = ffffffc00165f000
[00000218] *pgd=000000000174f003, *pud=000000000174f003,
				*pmd=0000000001750003, *pte=00e8000001751713
Internal error: Oops: 96000005 [#1] PREEMPT SMP
Modules linked in: uinput uvcvideo videobuf2_vmalloc cmac
ipt_MASQUERADE nf_nat_masquerade_ipv4 iptable_nat nf_nat_ipv4 nf_nat rfcomm
xt_mark fuse bridge stp llc zram btusb btrtl btbcm btintel bluetooth
ip6table_filter mwifiex_pcie mwifiex cfg80211 cdc_ether usbnet r8152 mii joydev
snd_seq_midi snd_seq_midi_event snd_rawmidi snd_seq snd_seq_device ppp_async
ppp_generic slhc tun
CPU: 1 PID: 29814 Comm: kworker/1:1 Not tainted 4.4.52 #507
Hardware name: Google Kevin (DT)
Workqueue: pm pm_runtime_work
task: ffffffc0ac540000 ti: ffffffc0af4d4000 task.ti: ffffffc0af4d4000
PC is at autosuspend_check+0x74/0x174
LR is at autosuspend_check+0x70/0x174
...
Call trace:
[] autosuspend_check+0x74/0x174
[] usb_runtime_idle+0x20/0x40
[] __rpm_callback+0x48/0x7c
[] rpm_idle+0x1e8/0x498
[] pm_runtime_work+0x88/0xcc
[] process_one_work+0x390/0x6b8
[] worker_thread+0x480/0x610
[] kthread+0x164/0x178
[] ret_from_fork+0x10/0x40

Source:

(gdb) l *0xffffffc00080dcc0
0xffffffc00080dcc0 is in autosuspend_check
(drivers/usb/core/driver.c:1778).
1773		/* We don't need to check interfaces that are
1774		 * disabled for runtime PM.  Either they are unbound
1775		 * or else their drivers don't support autosuspend
1776		 * and so they are permanently active.
1777		 */
1778		if (intf->dev.power.disable_depth)
1779			continue;
1780		if (atomic_read(&intf->dev.power.usage_count) > 0)
1781			return -EBUSY;
1782		w |= intf->needs_remote_wakeup;

Code analysis shows that intf is set to NULL in usb_disable_device() prior
to setting actconfig to NULL. At the same time, usb_runtime_idle() does not
lock the usb device, and neither does any of the functions in the
traceback. This means that there is no protection against a race condition
where usb_disable_device() is removing dev->actconfig->interface[] pointers
while those are being accessed from autosuspend_check().

To solve the problem, synchronize and validate device state between
autosuspend_check() and usb_disconnect().

Acked-by: Alan Stern 
Signed-off-by: Guenter Roeck 
Signed-off-by: Greg Kroah-Hartman

usb: hub: Fix error loop seen after hub communication errors

2017-05-20T12:30:56+00:00

commit 245b2eecee2aac6fdc77dcafaa73c33f9644c3c7 upstream.

While stress testing a usb controller using a bind/unbind looop, the
following error loop was observed.

usb 7-1.2: new low-speed USB device number 3 using xhci-hcd
usb 7-1.2: hub failed to enable device, error -108
usb 7-1-port2: cannot disable (err = -22)
usb 7-1-port2: couldn't allocate usb_device
usb 7-1-port2: cannot disable (err = -22)
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
hub 7-1:1.0: activate --> -22
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
hub 7-1:1.0: activate --> -22
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
hub 7-1:1.0: activate --> -22
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
hub 7-1:1.0: activate --> -22
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
hub 7-1:1.0: activate --> -22
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
hub 7-1:1.0: activate --> -22
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
hub 7-1:1.0: activate --> -22
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
hub 7-1:1.0: activate --> -22
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
** 57 printk messages dropped ** hub 7-1:1.0: activate --> -22
** 82 printk messages dropped ** hub 7-1:1.0: hub_ext_port_status failed (err = -22)

This continues forever. After adding tracebacks into the code,
the call sequence leading to this is found to be as follows.

[] hub_activate+0x368/0x7b8
[] hub_resume+0x2c/0x3c
[] usb_resume_interface.isra.6+0x128/0x158
[] usb_suspend_both+0x1e8/0x288
[] usb_runtime_suspend+0x3c/0x98
[] __rpm_callback+0x48/0x7c
[] rpm_callback+0xa8/0xd4
[] rpm_suspend+0x84/0x758
[] rpm_idle+0x2c8/0x498
[] __pm_runtime_idle+0x60/0xac
[] usb_autopm_put_interface+0x6c/0x7c
[] hub_event+0x10ac/0x12ac
[] process_one_work+0x390/0x6b8
[] worker_thread+0x480/0x610
[] kthread+0x164/0x178
[] ret_from_fork+0x10/0x40

kick_hub_wq() is called from hub_activate() even after failures to
communicate with the hub. This results in an endless sequence of
hub event -> hub activate -> wq trigger -> hub event -> ...

Provide two solutions for the problem.

- Only trigger the hub event queue if communication with the hub
  is successful.
- After a suspend failure, only resume already suspended interfaces
  if the communication with the device is still possible.

Each of the changes fixes the observed problem. Use both to improve
robustness.

Acked-by: Alan Stern 
Signed-off-by: Guenter Roeck 
Signed-off-by: Greg Kroah-Hartman

USB: Proper handling of Race Condition when two USB class drivers try to call init_usb_class simultaneously

2017-05-20T12:30:55+00:00

commit 2f86a96be0ccb1302b7eee7855dbee5ce4dc5dfb upstream.

There is race condition when two USB class drivers try to call
init_usb_class at the same time and leads to crash.
code path: probe->usb_register_dev->init_usb_class

To solve this, mutex locking has been added in init_usb_class() and
destroy_usb_class().

As pointed by Alan, removed "if (usb_class)" test from destroy_usb_class()
because usb_class can never be NULL there.

Signed-off-by: Ajay Kaher 
Acked-by: Alan Stern 
Signed-off-by: Greg Kroah-Hartman

USB: fix linked-list corruption in rh_call_control()

2017-04-08T07:35:08+00:00

commit 1633682053a7ee8058e10c76722b9b28e97fb73f upstream.

Using KASAN, Dmitry found a bug in the rh_call_control() routine: If
buffer allocation fails, the routine returns immediately without
unlinking its URB from the control endpoint, eventually leading to
linked-list corruption.

This patch fixes the problem by jumping to the end of the routine
(where the URB is unlinked) when an allocation failure occurs.

Signed-off-by: Alan Stern 
Reported-and-tested-by: Dmitry Vyukov 
Signed-off-by: Greg Kroah-Hartman

usb: hub: Fix crash after failure to read BOS descriptor

2017-03-30T07:44:05+00:00

commit 7b2db29fbb4e766fcd02207eb2e2087170bd6ebc upstream.

If usb_get_bos_descriptor() returns an error, usb->bos will be NULL.
Nevertheless, it is dereferenced unconditionally in
hub_set_initial_usb2_lpm_policy() if usb2_hw_lpm_capable is set.
This results in a crash.

usb 5-1: unable to get BOS descriptor
...
Unable to handle kernel NULL pointer dereference at virtual address 00000008
pgd = ffffffc00165f000
[00000008] *pgd=000000000174f003, *pud=000000000174f003,
		*pmd=0000000001750003, *pte=00e8000001751713
Internal error: Oops: 96000005 [#1] PREEMPT SMP
Modules linked in: uinput uvcvideo videobuf2_vmalloc cmac [ ... ]
CPU: 5 PID: 3353 Comm: kworker/5:3 Tainted: G    B 4.4.52 #480
Hardware name: Google Kevin (DT)
Workqueue: events driver_set_config_work
task: ffffffc0c3690000 ti: ffffffc0ae9a8000 task.ti: ffffffc0ae9a8000
PC is at hub_port_init+0xc3c/0xd10
LR is at hub_port_init+0xc3c/0xd10
...
Call trace:
[] hub_port_init+0xc3c/0xd10
[] usb_reset_and_verify_device+0x15c/0x82c
[] usb_reset_device+0xe4/0x298
[] rtl8152_probe+0x84/0x9b0 [r8152]
[] usb_probe_interface+0x244/0x2f8
[] driver_probe_device+0x180/0x3b4
[] __device_attach_driver+0xb4/0xe0
[] bus_for_each_drv+0xb4/0xe4
[] __device_attach+0xd0/0x158
[] device_initial_probe+0x24/0x30
[] bus_probe_device+0x50/0xe4
[] device_add+0x414/0x738
[] usb_set_configuration+0x89c/0x914
[] driver_set_config_work+0xc0/0xf0
[] process_one_work+0x390/0x6b8
[] worker_thread+0x480/0x610
[] kthread+0x164/0x178
[] ret_from_fork+0x10/0x40

Since we don't know anything about LPM capabilities without BOS descriptor,
don't attempt to enable LPM if it is not available.

Fixes: 890dae886721 ("xhci: Enable LPM support only for hardwired ...")
Cc: Mathias Nyman 
Signed-off-by: Guenter Roeck 
Acked-by: Mathias Nyman 
Signed-off-by: Greg Kroah-Hartman

usb-core: Add LINEAR_FRAME_INTR_BINTERVAL USB quirk

2017-03-30T07:44:04+00:00

commit 3243367b209faed5c320a4e5f9a565ee2a2ba958 upstream.

Some USB 2.0 devices erroneously report millisecond values in
bInterval. The generic config code manages to catch most of them,
but in some cases it's not completely enough.

The case at stake here is a USB 2.0 braille device, which wants to
announce 10ms and thus sets bInterval to 10, but with the USB 2.0
computation that yields to 64ms.  It happens that one can type fast
enough to reach this interval and get the device buffers overflown,
leading to problematic latencies.  The generic config code does not
catch this case because the 64ms is considered a sane enough value.

This change thus adds a USB_QUIRK_LINEAR_FRAME_INTR_BINTERVAL quirk
to mark devices which actually report milliseconds in bInterval,
and marks Vario Ultra devices as needing it.

Signed-off-by: Samuel Thibault 
Acked-by: Alan Stern 
Signed-off-by: Greg Kroah-Hartman

USB: Add quirk for WORLDE easykey.25 MIDI keyboard

2017-01-25T10:02:29+00:00

Add a quirk for WORLDE easykey.25 MIDI keyboard (idVendor=0218,
idProduct=0401). The device reports that it has config string
descriptor at index 3, but when the system selects the configuration
and tries to get the description, it returns a -EPROTO error,
the communication restarts and this keeps repeating over and over again.
Not requesting the string descriptor makes the device work correctly.

Relevant info from Wireshark:

[...]

CONFIGURATION DESCRIPTOR
    bLength: 9
    bDescriptorType: 0x02 (CONFIGURATION)
    wTotalLength: 101
    bNumInterfaces: 2
    bConfigurationValue: 1
    iConfiguration: 3
    Configuration bmAttributes: 0xc0  SELF-POWERED  NO REMOTE-WAKEUP
        1... .... = Must be 1: Must be 1 for USB 1.1 and higher
        .1.. .... = Self-Powered: This device is SELF-POWERED
        ..0. .... = Remote Wakeup: This device does NOT support remote wakeup
    bMaxPower: 50  (100mA)

[...]

     45 0.369104       host                  2.38.0                USB      64     GET DESCRIPTOR Request STRING

[...]

URB setup
    bmRequestType: 0x80
        1... .... = Direction: Device-to-host
        .00. .... = Type: Standard (0x00)
        ...0 0000 = Recipient: Device (0x00)
    bRequest: GET DESCRIPTOR (6)
    Descriptor Index: 0x03
    bDescriptorType: 0x03
    Language Id: English (United States) (0x0409)
    wLength: 255

     46 0.369255       2.38.0                host                  USB      64     GET DESCRIPTOR Response STRING[Malformed Packet]

[...]

Frame 46: 64 bytes on wire (512 bits), 64 bytes captured (512 bits) on interface 0
USB URB
    [Source: 2.38.0]
    [Destination: host]
    URB id: 0xffff88021f62d480
    URB type: URB_COMPLETE ('C')
    URB transfer type: URB_CONTROL (0x02)
    Endpoint: 0x80, Direction: IN
    Device: 38
    URB bus id: 2
    Device setup request: not relevant ('-')
    Data: present (0)
    URB sec: 1484896277
    URB usec: 455031
    URB status: Protocol error (-EPROTO) (-71)
    URB length [bytes]: 0
    Data length [bytes]: 0
    [Request in: 45]
    [Time from request: 0.000151000 seconds]
    Unused Setup Header
    Interval: 0
    Start frame: 0
    Copy of Transfer Flags: 0x00000200
    Number of ISO descriptors: 0
[Malformed Packet: USB]
    [Expert Info (Error/Malformed): Malformed Packet (Exception occurred)]
        [Malformed Packet (Exception occurred)]
        [Severity level: Error]
        [Group: Malformed]

Signed-off-by: Lukáš Lalinský 
Cc: stable 
Signed-off-by: Greg Kroah-Hartman

USB: fix problems with duplicate endpoint addresses

2017-01-05T18:38:40+00:00

When checking a new device's descriptors, the USB core does not check
for duplicate endpoint addresses.  This can cause a problem when the
sysfs files for those endpoints are created; trying to create multiple
files with the same name will provoke a WARNING:

WARNING: CPU: 2 PID: 865 at fs/sysfs/dir.c:31 sysfs_warn_dup+0x8a/0xa0
sysfs: cannot create duplicate filename
'/devices/platform/dummy_hcd.0/usb2/2-1/2-1:64.0/ep_05'
Kernel panic - not syncing: panic_on_warn set ...

CPU: 2 PID: 865 Comm: kworker/2:1 Not tainted 4.9.0-rc7+ #34
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
Workqueue: usb_hub_wq hub_event
 ffff88006bee64c8 ffffffff81f96b8a ffffffff00000001 1ffff1000d7dcc2c
 ffffed000d7dcc24 0000000000000001 0000000041b58ab3 ffffffff8598b510
 ffffffff81f968f8 ffffffff850fee20 ffffffff85cff020 dffffc0000000000
Call Trace:
 [<     inline     >] __dump_stack lib/dump_stack.c:15
 [] dump_stack+0x292/0x398 lib/dump_stack.c:51
 [] panic+0x1cb/0x3a9 kernel/panic.c:179
 [] __warn+0x1c4/0x1e0 kernel/panic.c:542
 [] warn_slowpath_fmt+0xc5/0x110 kernel/panic.c:565
 [] sysfs_warn_dup+0x8a/0xa0 fs/sysfs/dir.c:30
 [] sysfs_create_dir_ns+0x178/0x1d0 fs/sysfs/dir.c:59
 [<     inline     >] create_dir lib/kobject.c:71
 [] kobject_add_internal+0x227/0xa60 lib/kobject.c:229
 [<     inline     >] kobject_add_varg lib/kobject.c:366
 [] kobject_add+0x139/0x220 lib/kobject.c:411
 [] device_add+0x353/0x1660 drivers/base/core.c:1088
 [] device_register+0x1d/0x20 drivers/base/core.c:1206
 [] usb_create_ep_devs+0x163/0x260 drivers/usb/core/endpoint.c:195
 [] create_intf_ep_devs+0x13b/0x200 drivers/usb/core/message.c:1030
 [] usb_set_configuration+0x1083/0x18d0 drivers/usb/core/message.c:1937
 [] generic_probe+0x6e/0xe0 drivers/usb/core/generic.c:172
 [] usb_probe_device+0xaa/0xe0 drivers/usb/core/driver.c:263

This patch prevents the problem by checking for duplicate endpoint
addresses during enumeration and skipping any duplicates.

Signed-off-by: Alan Stern 
Reported-by: Andrey Konovalov 
Tested-by: Andrey Konovalov 
CC: 
Signed-off-by: Greg Kroah-Hartman

usb: hub: Move hub_port_disable() to fix warning if PM is disabled

2017-01-05T18:24:55+00:00

If CONFIG_PM=n:

    drivers/usb/core/hub.c:107: warning: ‘hub_usb3_port_prepare_disable’ declared inline after being called
    drivers/usb/core/hub.c:107: warning: previous declaration of ‘hub_usb3_port_prepare_disable’ was here

To fix this, move hub_port_disable() after
hub_usb3_port_prepare_disable(), and adjust forward declarations.

Fixes: 37be66767e3cae4f ("usb: hub: Fix auto-remount of safely removed or ejected USB-3 devices")
Signed-off-by: Geert Uytterhoeven 
Signed-off-by: Greg Kroah-Hartman

Replace with globally

2016-12-24T19:46:01+00:00

This was entirely automated, using the script by Al:

  PATT='^[[:blank:]]*#[[:blank:]]*include[[:blank:]]*'
  sed -i -e "s!$PATT!#include !" \
        $(git grep -l "$PATT"|grep -v ^include/linux/uaccess.h)

to do the replacement at the end of the merge window.

Requested-by: Al Viro 
Signed-off-by: Linus Torvalds