linux-stable.git/drivers/usb/core, branch linux-3.18.y Linux kernel stable tree USB: core: Fix bug caused by duplicate interface PM usage counter 2019-05-16T07:17:18+00:00 Alan Stern stern@rowland.harvard.edu 2019-04-19T17:52:38+00:00 bc1c5d1ac4772cbc39e485ee94bdf2e9d8a2cd7d commit c2b71462d294cf517a0bc6e4fd6424d7cee5596f upstream. The syzkaller fuzzer reported a bug in the USB hub driver which turned out to be caused by a negative runtime-PM usage counter. This allowed a hub to be runtime suspended at a time when the driver did not expect it. The symptom is a WARNING issued because the hub's status URB is submitted while it is already active: URB 0000000031fb463e submitted while active WARNING: CPU: 0 PID: 2917 at drivers/usb/core/urb.c:363 The negative runtime-PM usage count was caused by an unfortunate design decision made when runtime PM was first implemented for USB. At that time, USB class drivers were allowed to unbind from their interfaces without balancing the usage counter (i.e., leaving it with a positive count). The core code would take care of setting the counter back to 0 before allowing another driver to bind to the interface. Later on when runtime PM was implemented for the entire kernel, the opposite decision was made: Drivers were required to balance their runtime-PM get and put calls. In order to maintain backward compatibility, however, the USB subsystem adapted to the new implementation by keeping an independent usage counter for each interface and using it to automatically adjust the normal usage counter back to 0 whenever a driver was unbound. This approach involves duplicating information, but what is worse, it doesn't work properly in cases where a USB class driver delays decrementing the usage counter until after the driver's disconnect() routine has returned and the counter has been adjusted back to 0. Doing so would cause the usage counter to become negative. There's even a warning about this in the USB power management documentation! As it happens, this is exactly what the hub driver does. The kick_hub_wq() routine increments the runtime-PM usage counter, and the corresponding decrement is carried out by hub_event() in the context of the hub_wq work-queue thread. This work routine may sometimes run after the driver has been unbound from its interface, and when it does it causes the usage counter to go negative. It is not possible for hub_disconnect() to wait for a pending hub_event() call to finish, because hub_disconnect() is called with the device lock held and hub_event() acquires that lock. The only feasible fix is to reverse the original design decision: remove the duplicate interface-specific usage counter and require USB drivers to balance their runtime PM gets and puts. As far as I know, all existing drivers currently do this. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-and-tested-by: syzbot+7634edaea4d0b341c625@syzkaller.appspotmail.com CC: <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit c2b71462d294cf517a0bc6e4fd6424d7cee5596f upstream.

The syzkaller fuzzer reported a bug in the USB hub driver which turned
out to be caused by a negative runtime-PM usage counter.  This allowed
a hub to be runtime suspended at a time when the driver did not expect
it.  The symptom is a WARNING issued because the hub's status URB is
submitted while it is already active:

	URB 0000000031fb463e submitted while active
	WARNING: CPU: 0 PID: 2917 at drivers/usb/core/urb.c:363

The negative runtime-PM usage count was caused by an unfortunate
design decision made when runtime PM was first implemented for USB.
At that time, USB class drivers were allowed to unbind from their
interfaces without balancing the usage counter (i.e., leaving it with
a positive count).  The core code would take care of setting the
counter back to 0 before allowing another driver to bind to the
interface.

Later on when runtime PM was implemented for the entire kernel, the
opposite decision was made: Drivers were required to balance their
runtime-PM get and put calls.  In order to maintain backward
compatibility, however, the USB subsystem adapted to the new
implementation by keeping an independent usage counter for each
interface and using it to automatically adjust the normal usage
counter back to 0 whenever a driver was unbound.

This approach involves duplicating information, but what is worse, it
doesn't work properly in cases where a USB class driver delays
decrementing the usage counter until after the driver's disconnect()
routine has returned and the counter has been adjusted back to 0.
Doing so would cause the usage counter to become negative.  There's
even a warning about this in the USB power management documentation!

As it happens, this is exactly what the hub driver does.  The
kick_hub_wq() routine increments the runtime-PM usage counter, and the
corresponding decrement is carried out by hub_event() in the context
of the hub_wq work-queue thread.  This work routine may sometimes run
after the driver has been unbound from its interface, and when it does
it causes the usage counter to go negative.

It is not possible for hub_disconnect() to wait for a pending
hub_event() call to finish, because hub_disconnect() is called with
the device lock held and hub_event() acquires that lock.  The only
feasible fix is to reverse the original design decision: remove the
duplicate interface-specific usage counter and require USB drivers to
balance their runtime PM gets and puts.  As far as I know, all
existing drivers currently do this.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: syzbot+7634edaea4d0b341c625@syzkaller.appspotmail.com
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB: core: Fix unterminated string returned by usb_string() 2019-05-16T07:17:17+00:00 Alan Stern stern@rowland.harvard.edu 2019-04-15T15:51:38+00:00 652c6e122fda6aec8754ac3a3aa4720860dbb836 commit c01c348ecdc66085e44912c97368809612231520 upstream. Some drivers (such as the vub300 MMC driver) expect usb_string() to return a properly NUL-terminated string, even when an error occurs. (In fact, vub300's probe routine doesn't bother to check the return code from usb_string().) When the driver goes on to use an unterminated string, it leads to kernel errors such as stack-out-of-bounds, as found by the syzkaller USB fuzzer. An out-of-range string index argument is not at all unlikely, given that some devices don't provide string descriptors and therefore list 0 as the value for their string indexes. This patch makes usb_string() return a properly terminated empty string along with the -EINVAL error code when an out-of-range index is encountered. And since a USB string index is a single-byte value, indexes >= 256 are just as invalid as values of 0 or below. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-by: syzbot+b75b85111c10b8d680f1@syzkaller.appspotmail.com CC: <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit c01c348ecdc66085e44912c97368809612231520 upstream.

Some drivers (such as the vub300 MMC driver) expect usb_string() to
return a properly NUL-terminated string, even when an error occurs.
(In fact, vub300's probe routine doesn't bother to check the return
code from usb_string().)  When the driver goes on to use an
unterminated string, it leads to kernel errors such as
stack-out-of-bounds, as found by the syzkaller USB fuzzer.

An out-of-range string index argument is not at all unlikely, given
that some devices don't provide string descriptors and therefore list
0 as the value for their string indexes.  This patch makes
usb_string() return a properly terminated empty string along with the
-EINVAL error code when an out-of-range index is encountered.

And since a USB string index is a single-byte value, indexes >= 256
are just as invalid as values of 0 or below.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: syzbot+b75b85111c10b8d680f1@syzkaller.appspotmail.com
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb: hub: delay hub autosuspend if USB3 port is still link training 2019-02-20T09:08:58+00:00 Mathias Nyman mathias.nyman@linux.intel.com 2018-11-28T13:55:21+00:00 e40c219934a5b8caea25a94a2774d9515c9404d7 [ Upstream commit e86108940e541febf35813402ff29fa6f4a9ac0b ] When initializing a hub we want to give a USB3 port in link training the same debounce delay time before autosuspening the hub as already trained, connected enabled ports. USB3 ports won't reach the enabled state with "current connect status" and "connect status change" bits set until the USB3 link training finishes. Catching the port in link training (polling) and adding the debounce delay prevents unnecessary failed attempts to autosuspend the hub. Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit e86108940e541febf35813402ff29fa6f4a9ac0b ]

When initializing a hub we want to give a USB3 port in link training
the same debounce delay time before autosuspening the hub as already
trained, connected enabled ports.

USB3 ports won't reach the enabled state with "current connect status" and
"connect status change" bits set until the USB3 link training finishes.

Catching the port in link training (polling) and adding the debounce delay
prevents unnecessary failed attempts to autosuspend the hub.

Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
USB: check usb_get_extra_descriptor for proper size 2018-12-13T08:22:31+00:00 Mathias Payer mathias.payer@nebelwelt.net 2018-12-05T20:19:59+00:00 d672c306e00a904adcbdce42b51b23b3e906f5cf commit 704620afc70cf47abb9d6a1a57f3825d2bca49cf upstream. When reading an extra descriptor, we need to properly check the minimum and maximum size allowed, to prevent from invalid data being sent by a device. Reported-by: Hui Peng <benquike@gmail.com> Reported-by: Mathias Payer <mathias.payer@nebelwelt.net> Co-developed-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Hui Peng <benquike@gmail.com> Signed-off-by: Mathias Payer <mathias.payer@nebelwelt.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 704620afc70cf47abb9d6a1a57f3825d2bca49cf upstream.

When reading an extra descriptor, we need to properly check the minimum
and maximum size allowed, to prevent from invalid data being sent by a
device.

Reported-by: Hui Peng <benquike@gmail.com>
Reported-by: Mathias Payer <mathias.payer@nebelwelt.net>
Co-developed-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Hui Peng <benquike@gmail.com>
Signed-off-by: Mathias Payer <mathias.payer@nebelwelt.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb: quirk: add no-LPM quirk on SanDisk Ultra Flair device 2018-12-13T08:22:31+00:00 Harry Pan harry.pan@intel.com 2018-11-28T16:40:41+00:00 b8d5012991fb9770848de292a48498a9db3aeed1 commit 2f2dde6ba89b1ef1fe23c1138131b315d9aa4019 upstream. Some lower volume SanDisk Ultra Flair in 16GB, which the VID:PID is in 0781:5591, will aggressively request LPM of U1/U2 during runtime, when using this thumb drive as the OS installation key we found the device will generate failure during U1 exit path making it dropped from the USB bus, this causes a corrupted installation in system at the end. i.e., [ 166.918296] hub 2-0:1.0: state 7 ports 7 chg 0000 evt 0004 [ 166.918327] usb usb2-port2: link state change [ 166.918337] usb usb2-port2: do warm reset [ 166.970039] usb usb2-port2: not warm reset yet, waiting 50ms [ 167.022040] usb usb2-port2: not warm reset yet, waiting 200ms [ 167.276043] usb usb2-port2: status 02c0, change 0041, 5.0 Gb/s [ 167.276050] usb 2-2: USB disconnect, device number 2 [ 167.276058] usb 2-2: unregistering device [ 167.276060] usb 2-2: unregistering interface 2-2:1.0 [ 167.276170] xhci_hcd 0000:00:15.0: shutdown urb ffffa3c7cc695cc0 ep1in-bulk [ 167.284055] sd 0:0:0:0: [sda] tag#0 FAILED Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK [ 167.284064] sd 0:0:0:0: [sda] tag#0 CDB: Read(10) 28 00 00 33 04 90 00 01 00 00 ... Analyzed the USB trace in the link layer we realized it is because of the 6-ms timer of tRecoveryConfigurationTimeout which documented on the USB 3.2 Revision 1.0, the section 7.5.10.4.2 of "Exit from Recovery.Configuration"; device initiates U1 exit -> Recovery.Active -> Recovery.Configuration, then the host timer timeout makes the link transits to eSS.Inactive -> Rx.Detect follows by a Warm Reset. Interestingly, the other higher volume of SanDisk Ultra Flair sharing the same VID:PID, such as 64GB, would not request LPM during runtime, it sticks at U0 always, thus disabling LPM does not affect those thumb drives at all. The same odd occures in SanDisk Ultra Fit 16GB, VID:PID in 0781:5583. Signed-off-by: Harry Pan <harry.pan@intel.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 2f2dde6ba89b1ef1fe23c1138131b315d9aa4019 upstream.

Some lower volume SanDisk Ultra Flair in 16GB, which the VID:PID is
in 0781:5591, will aggressively request LPM of U1/U2 during runtime,
when using this thumb drive as the OS installation key we found the
device will generate failure during U1 exit path making it dropped
from the USB bus, this causes a corrupted installation in system at
the end.

i.e.,
[  166.918296] hub 2-0:1.0: state 7 ports 7 chg 0000 evt 0004
[  166.918327] usb usb2-port2: link state change
[  166.918337] usb usb2-port2: do warm reset
[  166.970039] usb usb2-port2: not warm reset yet, waiting 50ms
[  167.022040] usb usb2-port2: not warm reset yet, waiting 200ms
[  167.276043] usb usb2-port2: status 02c0, change 0041, 5.0 Gb/s
[  167.276050] usb 2-2: USB disconnect, device number 2
[  167.276058] usb 2-2: unregistering device
[  167.276060] usb 2-2: unregistering interface 2-2:1.0
[  167.276170] xhci_hcd 0000:00:15.0: shutdown urb ffffa3c7cc695cc0 ep1in-bulk
[  167.284055] sd 0:0:0:0: [sda] tag#0 FAILED Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
[  167.284064] sd 0:0:0:0: [sda] tag#0 CDB: Read(10) 28 00 00 33 04 90 00 01 00 00
...

Analyzed the USB trace in the link layer we realized it is because
of the 6-ms timer of tRecoveryConfigurationTimeout which documented
on the USB 3.2 Revision 1.0, the section 7.5.10.4.2 of "Exit from
Recovery.Configuration"; device initiates U1 exit -> Recovery.Active
-> Recovery.Configuration, then the host timer timeout makes the link
transits to eSS.Inactive -> Rx.Detect follows by a Warm Reset.

Interestingly, the other higher volume of SanDisk Ultra Flair sharing
the same VID:PID, such as 64GB, would not request LPM during runtime,
it sticks at U0 always, thus disabling LPM does not affect those thumb
drives at all.

The same odd occures in SanDisk Ultra Fit 16GB, VID:PID in 0781:5583.

Signed-off-by: Harry Pan <harry.pan@intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb: core: quirks: add RESET_RESUME quirk for Cherry G230 Stream series 2018-12-13T08:22:28+00:00 Michael Niewöhner linux@mniewoehner.de 2018-11-25T16:57:33+00:00 dc931191788a43db30beea20c06e6edef5ba5d12 commit effd14f66cc1ef6701a19c5a56e39c35f4d395a5 upstream. Cherry G230 Stream 2.0 (G85-231) and 3.0 (G85-232) need this quirk to function correctly. This fixes a but where double pressing numlock locks up the device completely with need to replug the keyboard. Signed-off-by: Michael Niewöhner <linux@mniewoehner.de> Tested-by: Michael Niewöhner <linux@mniewoehner.de> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit effd14f66cc1ef6701a19c5a56e39c35f4d395a5 upstream.

Cherry G230 Stream 2.0 (G85-231) and 3.0 (G85-232) need this quirk to
function correctly. This fixes a but where double pressing numlock locks
up the device completely with need to replug the keyboard.

Signed-off-by: Michael Niewöhner <linux@mniewoehner.de>
Tested-by: Michael Niewöhner <linux@mniewoehner.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb: core: Fix hub port connection events lost 2018-12-01T08:47:58+00:00 Dennis Wassenberg dennis.wassenberg@secunet.com 2018-11-13T13:40:34+00:00 161a4fe3a36e3ba700f9e8b4376c06de4a74d4ba commit 22454b79e6de05fa61a2a72d00d2eed798abbb75 upstream. This will clear the USB_PORT_FEAT_C_CONNECTION bit in case of a hub port reset only if a device is was attached to the hub port before resetting the hub port. Using a Lenovo T480s attached to the ultra dock it was not possible to detect some usb-c devices at the dock usb-c ports because the hub_port_reset code will clear the USB_PORT_FEAT_C_CONNECTION bit after the actual hub port reset. Using this device combo the USB_PORT_FEAT_C_CONNECTION bit was set between the actual hub port reset and the clear of the USB_PORT_FEAT_C_CONNECTION bit. This ends up with clearing the USB_PORT_FEAT_C_CONNECTION bit after the new device was attached such that it was not detected. This patch will not clear the USB_PORT_FEAT_C_CONNECTION bit if there is currently no device attached to the port before the hub port reset. This will avoid clearing the connection bit for new attached devices. Signed-off-by: Dennis Wassenberg <dennis.wassenberg@secunet.com> Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 22454b79e6de05fa61a2a72d00d2eed798abbb75 upstream.

This will clear the USB_PORT_FEAT_C_CONNECTION bit in case of a hub port reset
only if a device is was attached to the hub port before resetting the hub port.

Using a Lenovo T480s attached to the ultra dock it was not possible to detect
some usb-c devices at the dock usb-c ports because the hub_port_reset code
will clear the USB_PORT_FEAT_C_CONNECTION bit after the actual hub port reset.
Using this device combo the USB_PORT_FEAT_C_CONNECTION bit was set between the
actual hub port reset and the clear of the USB_PORT_FEAT_C_CONNECTION bit.
This ends up with clearing the USB_PORT_FEAT_C_CONNECTION bit after the
new device was attached such that it was not detected.

This patch will not clear the USB_PORT_FEAT_C_CONNECTION bit if there is
currently no device attached to the port before the hub port reset.
This will avoid clearing the connection bit for new attached devices.

Signed-off-by: Dennis Wassenberg <dennis.wassenberg@secunet.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb: quirks: Add delay-init quirk for Corsair K70 LUX RGB 2018-11-27T15:05:37+00:00 Emmanuel Pescosta emmanuelpescosta099@gmail.com 2018-10-26T12:48:09+00:00 7f1643f1daf01028f3239a39683bd409984c0bb5 commit a77112577667cbda7c6292c52d909636aef31fd9 upstream. Following on from this patch: https://lkml.org/lkml/2017/11/3/516, Corsair K70 LUX RGB keyboards also require the DELAY_INIT quirk to start correctly at boot. Dmesg output: usb 1-6: string descriptor 0 read error: -110 usb 1-6: New USB device found, idVendor=1b1c, idProduct=1b33 usb 1-6: New USB device strings: Mfr=1, Product=2, SerialNumber=3 usb 1-6: can't set config #1, error -110 Signed-off-by: Emmanuel Pescosta <emmanuelpescosta099@gmail.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit a77112577667cbda7c6292c52d909636aef31fd9 upstream.

Following on from this patch: https://lkml.org/lkml/2017/11/3/516,
Corsair K70 LUX RGB keyboards also require the DELAY_INIT quirk to
start correctly at boot.

Dmesg output:
usb 1-6: string descriptor 0 read error: -110
usb 1-6: New USB device found, idVendor=1b1c, idProduct=1b33
usb 1-6: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 1-6: can't set config #1, error -110

Signed-off-by: Emmanuel Pescosta <emmanuelpescosta099@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB: quirks: Add no-lpm quirk for Raydium touchscreens 2018-11-27T15:05:37+00:00 Kai-Heng Feng kai.heng.feng@canonical.com 2018-10-26T05:33:15+00:00 f4dd27ef44564fd1dccd0a2480fa91cb182be41d commit deefd24228a172d1b27d4a9adbfd2cdacd60ae64 upstream. Raydium USB touchscreen fails to set config if LPM is enabled: [ 2.030658] usb 1-8: New USB device found, idVendor=2386, idProduct=3119 [ 2.030659] usb 1-8: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 2.030660] usb 1-8: Product: Raydium Touch System [ 2.030661] usb 1-8: Manufacturer: Raydium Corporation [ 7.132209] usb 1-8: can't set config #1, error -110 Same behavior can be observed on 2386:3114. Raydium claims the touchscreen supports LPM under Windows, so I used Microsoft USB Test Tools (MUTT) [1] to check its LPM status. MUTT shows that the LPM doesn't work under Windows, either. So let's just disable LPM for Raydium touchscreens. [1] https://docs.microsoft.com/en-us/windows-hardware/drivers/usbcon/usb-test-tools Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit deefd24228a172d1b27d4a9adbfd2cdacd60ae64 upstream.

Raydium USB touchscreen fails to set config if LPM is enabled:
[    2.030658] usb 1-8: New USB device found, idVendor=2386, idProduct=3119
[    2.030659] usb 1-8: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    2.030660] usb 1-8: Product: Raydium Touch System
[    2.030661] usb 1-8: Manufacturer: Raydium Corporation
[    7.132209] usb 1-8: can't set config #1, error -110

Same behavior can be observed on 2386:3114.

Raydium claims the touchscreen supports LPM under Windows, so I used
Microsoft USB Test Tools (MUTT) [1] to check its LPM status. MUTT shows
that the LPM doesn't work under Windows, either. So let's just disable LPM
for Raydium touchscreens.

[1] https://docs.microsoft.com/en-us/windows-hardware/drivers/usbcon/usb-test-tools

Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB: fix the usbfs flag sanitization for control transfers 2018-11-10T15:39:23+00:00 Alan Stern stern@rowland.harvard.edu 2018-10-15T20:55:04+00:00 341d66bbf7f8fd00569da77897ec1c28c83c6201 commit 665c365a77fbfeabe52694aedf3446d5f2f1ce42 upstream. Commit 7a68d9fb8510 ("USB: usbdevfs: sanitize flags more") checks the transfer flags for URBs submitted from userspace via usbfs. However, the check for whether the USBDEVFS_URB_SHORT_NOT_OK flag should be allowed for a control transfer was added in the wrong place, before the code has properly determined the direction of the control transfer. (Control transfers are special because for them, the direction is set by the bRequestType byte of the Setup packet rather than direction bit of the endpoint address.) This patch moves code which sets up the allow_short flag for control transfers down after is_in has been set to the correct value. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-and-tested-by: syzbot+24a30223a4b609bb802e@syzkaller.appspotmail.com Fixes: 7a68d9fb8510 ("USB: usbdevfs: sanitize flags more") CC: Oliver Neukum <oneukum@suse.com> CC: <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 665c365a77fbfeabe52694aedf3446d5f2f1ce42 upstream.

Commit 7a68d9fb8510 ("USB: usbdevfs: sanitize flags more") checks the
transfer flags for URBs submitted from userspace via usbfs.  However,
the check for whether the USBDEVFS_URB_SHORT_NOT_OK flag should be
allowed for a control transfer was added in the wrong place, before
the code has properly determined the direction of the control
transfer.  (Control transfers are special because for them, the
direction is set by the bRequestType byte of the Setup packet rather
than direction bit of the endpoint address.)

This patch moves code which sets up the allow_short flag for control
transfers down after is_in has been set to the correct value.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: syzbot+24a30223a4b609bb802e@syzkaller.appspotmail.com
Fixes: 7a68d9fb8510 ("USB: usbdevfs: sanitize flags more")
CC: Oliver Neukum <oneukum@suse.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>