linux-stable.git/drivers/usb/core/driver.c, branch linux-3.8.y

Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial

2012-12-13T20:00:02+00:00

Pull trivial branch from Jiri Kosina:
 "Usual stuff -- comment/printk typo fixes, documentation updates, dead
  code elimination."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
  HOWTO: fix double words typo
  x86 mtrr: fix comment typo in mtrr_bp_init
  propagate name change to comments in kernel source
  doc: Update the name of profiling based on sysfs
  treewide: Fix typos in various drivers
  treewide: Fix typos in various Kconfig
  wireless: mwifiex: Fix typo in wireless/mwifiex driver
  messages: i2o: Fix typo in messages/i2o
  scripts/kernel-doc: check that non-void fcts describe their return value
  Kernel-doc: Convention: Use a "Return" section to describe return values
  radeon: Fix typo and copy/paste error in comments
  doc: Remove unnecessary declarations from Documentation/accounting/getdelays.c
  various: Fix spelling of "asynchronous" in comments.
  Fix misspellings of "whether" in comments.
  eisa: Fix spelling of "asynchronous".
  various: Fix spelling of "registered" in comments.
  doc: fix quite a few typos within Documentation
  target: iscsi: fix comment typos in target/iscsi drivers
  treewide: fix typo of "suport" in various comments and Kconfig
  treewide: fix typo of "suppport" in various comments
  ...

usb-core: remove CONFIG_HOTPLUG ifdefs

2012-11-21T21:27:16+00:00

Remove conditional code based on CONFIG_HOTPLUG being false.  It's
always on now in preparation of it going away as an option.

Signed-off-by: Bill Pemberton 
Signed-off-by: Greg Kroah-Hartman

treewide: fix typo of "suport" in various comments and Kconfig

2012-11-19T13:16:09+00:00

Signed-off-by: Masanari Iida 
Signed-off-by: Jiri Kosina

USB: Enable LPM after a failed probe.

2012-10-08T18:47:40+00:00

Before a driver is probed, we want to disable USB 3.0 Link Power
Management (LPM), in case the driver needs hub-initiated LPM disabled.
After the probe finishes, we want to attempt to re-enable LPM, order to
balance the LPM ref count.

When a probe fails (such as when libusual doesn't want to bind to a USB
3.0 mass storage device), make sure to balance the LPM ref counts by
re-enabling LPM.

This patch should be backported to kernels as old as 3.5, that contain
the commit 8306095fd2c1100e8244c09bf560f97aca5a311d "USB: Disable USB
3.0 LPM in critical sections."

Signed-off-by: Sarah Sharp 
Cc: stable@vger.kernel.org

usb: remove junk from store_remove_id

2012-09-17T22:10:57+00:00

retval is 0, and carefully assigned - and tested as non zero.

This is not useful. While we are at it remove some other bogus initialisation
in the function

Signed-off-by: Alan Cox 
Signed-off-by: Greg Kroah-Hartman

usb: Add quirk detection based on interface information

2012-07-19T22:44:58+00:00

When a whole class of devices (possibly from a specific vendor, or
across multiple vendors) require a quirk, explictly listing all devices
in the class make the quirks table unnecessarily large. Fix this by
allowing matching devices based on interface information.

Signed-off-by: Laurent Pinchart 
Acked-by: Alan Stern 
Signed-off-by: Greg Kroah-Hartman

usb-core: Set intfdata to NULL if a driver's probe method failed

2012-06-13T23:07:22+00:00

Ensure that intfdata always is NULL if no driver is bound:
1) drvdata is for a driver to store a pointer to driver specific data
2) If no driver is bound, there is no driver specific data associated with
   the device
3) Thus logically drvdata should be NULL if no driver is bound.

We already set intfdata to NULL when a driver is unbound, to ensure that
intfdata will be NULL even if the drivers disconnect method does not properly
clear it. This ensures that intfdata will also be NULL after a failed probe,
even if the driver's probe method left a (likely dangling) pointer in there.

Signed-off-by: Hans de Goede 
Signed-off-by: Greg Kroah-Hartman

USB: allow match on bInterfaceNumber

2012-06-13T22:40:09+00:00

Some composite USB devices provide multiple interfaces
with different functions, all using "vendor-specific"
for class/subclass/protocol.  Another OS use interface
numbers to match the driver and interface. It seems
these devices are designed with that in mind - using
static interface numbers for the different functions.

This adds support for matching against the
bInterfaceNumber, allowing such devices to be supported
without having to resort to testing against interface
number whitelists and/or blacklists in the probe.

Signed-off-by: Bjørn Mork 
Signed-off-by: Greg Kroah-Hartman

USB: Disable USB 3.0 LPM in critical sections.

2012-05-18T22:41:59+00:00

There are several places where the USB core needs to disable USB 3.0
Link PM:
 - usb_bind_interface
 - usb_unbind_interface
 - usb_driver_claim_interface
 - usb_port_suspend/usb_port_resume
 - usb_reset_and_verify_device
 - usb_set_interface
 - usb_reset_configuration
 - usb_set_configuration

Use the new LPM disable/enable functions to temporarily disable LPM
around these critical sections.

We need to protect the critical section around binding and unbinding USB
interface drivers.  USB drivers may want to disable hub-initiated USB
3.0 LPM, which will change the value of the U1/U2 timeouts that the xHCI
driver will install.  We need to disable LPM completely until the driver
is bound to the interface, and the driver has a chance to enable
whatever alternate interface setting it needs in its probe routine.
Then re-enable USB3 LPM, and recalculate the U1/U2 timeout values.

We also need to disable LPM in usb_driver_claim_interface,
because drivers like usbfs can bind to an interface through that
function.  Note, there is no way currently for userspace drivers to
disable hub-initiated USB 3.0 LPM.  Revisit this later.

When a driver is unbound, the U1/U2 timeouts may change because we are
unbinding the last driver that needed hub-initiated USB 3.0 LPM to be
disabled.

USB LPM must be disabled when a USB device is going to be suspended.
The USB 3.0 spec does not define a state transition from U1 or U2 into
U3, so we need to bring the device into U0 by disabling LPM before we
can place it into U3.  Therefore, call usb_unlocked_disable_lpm() in
usb_port_suspend(), and call usb_unlocked_enable_lpm() in
usb_port_resume().  If the port suspend fails, make sure to re-enable
LPM by calling usb_unlocked_enable_lpm(), since usb_port_resume() will
not be called on a failed port suspend.

USB 3.0 devices lose their USB 3.0 LPM settings (including whether USB
device-initiated LPM is enabled) across device suspend.  Therefore,
disable LPM before the device will be reset in
usb_reset_and_verify_device(), and re-enable LPM after the reset is
complete and the configuration/alt settings are re-installed.

The calculated U1/U2 timeout values are heavily dependent on what USB
device endpoints are currently enabled.  When any of the enabled
endpoints on the device might change, due to a new configuration, or new
alternate interface setting, we need to first disable USB 3.0 LPM, add
or delete endpoints from the xHCI schedule, install the new interfaces
and alt settings, and then re-enable LPM.  Do this in usb_set_interface,
usb_reset_configuration, and usb_set_configuration.

Basically, there is a call to disable and then enable LPM in all
functions that lock the bandwidth_mutex.  One exception is
usb_disable_device, because the device is disconnecting or otherwise
going away, and we should not care about whether USB 3.0 LPM is enabled.

Signed-off-by: Sarah Sharp

USB: add read support to usb-serial/../new_id

2012-05-14T16:30:40+00:00

Keep the usb-serial support for dynamic IDs in sync with the usb
support.  This enables readout of dynamic device IDs for
usb-serial drivers.  Common code is exported from the usb core
system and reused by the usb-serial bus driver.

Signed-off-by: Bjørn Mork 
Signed-off-by: Greg Kroah-Hartman