linux-stable.git/drivers/tty, branch v6.9.9 Linux kernel stable tree serial: imx: Raise TX trigger level to 8 2024-07-11T10:51:05+00:00 Matthias Schiffer matthias.schiffer@ew.tq-group.com 2024-05-08T13:37:44+00:00 9377188736a09567ed9af88b8737d7c64c5053f3 [ Upstream commit a3d8728ab079951741efa11360df43dbfacba7ab ] At the default TX trigger level of 2 in non-DMA mode (meaning that an interrupt is generated when less than 2 characters are left in the FIFO), we have observed frequent buffer underruns at 115200 Baud on an i.MX8M Nano. This can cause communication issues if the receiving side expects a continuous transfer. Increasing the level to 8 makes the UART trigger an interrupt earlier, giving the kernel enough time to refill the FIFO, at the cost of triggering one interrupt per ~24 instead of ~30 bytes of transmitted data (as the i.MX UART has a 32 byte FIFO). Signed-off-by: Michael Krummsdorf <michael.krummsdorf@tq-group.com> Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com> Link: https://lore.kernel.org/r/20240508133744.35858-1-matthias.schiffer@ew.tq-group.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit a3d8728ab079951741efa11360df43dbfacba7ab ]

At the default TX trigger level of 2 in non-DMA mode (meaning that an
interrupt is generated when less than 2 characters are left in the
FIFO), we have observed frequent buffer underruns at 115200 Baud on an
i.MX8M Nano. This can cause communication issues if the receiving side
expects a continuous transfer.

Increasing the level to 8 makes the UART trigger an interrupt earlier,
giving the kernel enough time to refill the FIFO, at the cost of
triggering one interrupt per ~24 instead of ~30 bytes of transmitted
data (as the i.MX UART has a 32 byte FIFO).

Signed-off-by: Michael Krummsdorf <michael.krummsdorf@tq-group.com>
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Link: https://lore.kernel.org/r/20240508133744.35858-1-matthias.schiffer@ew.tq-group.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
serial: 8250_omap: Fix Errata i2310 with RX FIFO level check 2024-07-05T07:38:20+00:00 Udit Kumar u-kumar1@ti.com 2024-06-25T16:07:25+00:00 8fb36f85f7f9f6088e75bc6fd84890230d8a43f9 commit c128a1b0523b685c8856ddc0ac0e1caef1fdeee5 upstream. Errata i2310[0] says, Erroneous timeout can be triggered, if this Erroneous interrupt is not cleared then it may leads to storm of interrupts. Commit 9d141c1e6157 ("serial: 8250_omap: Implementation of Errata i2310") which added the workaround but missed ensuring RX FIFO is really empty before applying the errata workaround as recommended in the errata text. Fix this by adding back check for UART_OMAP_RX_LVL to be 0 for workaround to take effect. [0] https://www.ti.com/lit/pdf/sprz536 page 23 Fixes: 9d141c1e6157 ("serial: 8250_omap: Implementation of Errata i2310") Cc: stable@vger.kernel.org Reported-by: Vignesh Raghavendra <vigneshr@ti.com> Closes: https://lore.kernel.org/all/e96d0c55-0b12-4cbf-9d23-48963543de49@ti.com/ Signed-off-by: Udit Kumar <u-kumar1@ti.com> Link: https://lore.kernel.org/r/20240625160725.2102194-1-u-kumar1@ti.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit c128a1b0523b685c8856ddc0ac0e1caef1fdeee5 upstream.

Errata i2310[0] says, Erroneous timeout can be triggered,
if this Erroneous interrupt is not cleared then it may leads
to storm of interrupts.

Commit 9d141c1e6157 ("serial: 8250_omap: Implementation of Errata i2310")
which added the workaround but missed ensuring RX FIFO is really empty
before applying the errata workaround as recommended in the errata text.
Fix this by adding back check for UART_OMAP_RX_LVL to be 0 for
workaround to take effect.

[0] https://www.ti.com/lit/pdf/sprz536 page 23

Fixes: 9d141c1e6157 ("serial: 8250_omap: Implementation of Errata i2310")
Cc: stable@vger.kernel.org
Reported-by: Vignesh Raghavendra <vigneshr@ti.com>
Closes: https://lore.kernel.org/all/e96d0c55-0b12-4cbf-9d23-48963543de49@ti.com/
Signed-off-by: Udit Kumar <u-kumar1@ti.com>
Link: https://lore.kernel.org/r/20240625160725.2102194-1-u-kumar1@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
serial: imx: only set receiver level if it is zero 2024-07-05T07:38:20+00:00 Stefan Eichenberger stefan.eichenberger@toradex.com 2024-07-03T11:25:40+00:00 f05cdbe17a3fbd745554cf66767022b9660ee080 commit 9706fc87b4cff0ac4f5d5d62327be83fe72e3108 upstream. With commit a81dbd0463ec ("serial: imx: set receiver level before starting uart") we set the receiver level to its default value. This caused a regression when using SDMA, where the receiver level is 9 instead of 8 (default). This change will first check if the receiver level is zero and only then set it to the default. This still avoids the interrupt storm when the receiver level is zero. Fixes: a81dbd0463ec ("serial: imx: set receiver level before starting uart") Cc: stable <stable@kernel.org> Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com> Link: https://lore.kernel.org/r/20240703112543.148304-1-eichest@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 9706fc87b4cff0ac4f5d5d62327be83fe72e3108 upstream.

With commit a81dbd0463ec ("serial: imx: set receiver level before
starting uart") we set the receiver level to its default value. This
caused a regression when using SDMA, where the receiver level is 9
instead of 8 (default). This change will first check if the receiver
level is zero and only then set it to the default. This still avoids the
interrupt storm when the receiver level is zero.

Fixes: a81dbd0463ec ("serial: imx: set receiver level before starting uart")
Cc: stable <stable@kernel.org>
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
Link: https://lore.kernel.org/r/20240703112543.148304-1-eichest@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tty: mcf: MCF54418 has 10 UARTS 2024-07-05T07:38:11+00:00 Jean-Michel Hautbois jeanmichel.hautbois@yoseli.org 2024-06-20T16:29:59+00:00 f935def615ed2b8442b4e039b7b6f50de131efd4 commit 7c92a8bd53f24d50c8cf4aba53bb75505b382fed upstream. Most of the colfires have up to 5 UARTs but MCF54418 has up-to 10 ! Change the maximum value authorized. Signed-off-by: Jean-Michel Hautbois <jeanmichel.hautbois@yoseli.org> Cc: stable <stable@kernel.org> Fixes: 2545cf6e94b4 ("m68knommu: allow 4 coldfire serial ports") Link: https://lore.kernel.org/r/20240620-upstream-uart-v1-1-a9d0d95fb19e@yoseli.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 7c92a8bd53f24d50c8cf4aba53bb75505b382fed upstream.

Most of the colfires have up to 5 UARTs but MCF54418 has up-to 10 !
Change the maximum value authorized.

Signed-off-by: Jean-Michel Hautbois <jeanmichel.hautbois@yoseli.org>
Cc: stable <stable@kernel.org>
Fixes: 2545cf6e94b4 ("m68knommu: allow 4 coldfire serial ports")
Link: https://lore.kernel.org/r/20240620-upstream-uart-v1-1-a9d0d95fb19e@yoseli.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tty: mxser: Remove __counted_by from mxser_board.ports[] 2024-07-05T07:38:11+00:00 Nathan Chancellor nathan@kernel.org 2024-05-29T21:29:42+00:00 f07d45981814b8f98ad8d92921a6c4abc41a6fe6 commit 1c07c9be87dd3dd0634033bf08728b32465f08fb upstream. Work for __counted_by on generic pointers in structures (not just flexible array members) has started landing in Clang 19 (current tip of tree). During the development of this feature, a restriction was added to __counted_by to prevent the flexible array member's element type from including a flexible array member itself such as: struct foo { int count; char buf[]; }; struct bar { int count; struct foo data[] __counted_by(count); }; because the size of data cannot be calculated with the standard array size formula: sizeof(struct foo) * count This restriction was downgraded to a warning but due to CONFIG_WERROR, it can still break the build. The application of __counted_by on the ports member of 'struct mxser_board' triggers this restriction, resulting in: drivers/tty/mxser.c:291:2: error: 'counted_by' should not be applied to an array with element of unknown size because 'struct mxser_port' is a struct type with a flexible array member. This will be an error in a future compiler version [-Werror,-Wbounds-safety-counted-by-elt-type-unknown-size] 291 | struct mxser_port ports[] __counted_by(nports); | ^~~~~~~~~~~~~~~~~~~~~~~~~ 1 error generated. Remove this use of __counted_by to fix the warning/error. However, rather than remove it altogether, leave it commented, as it may be possible to support this in future compiler releases. Cc: <stable@vger.kernel.org> Closes: https://github.com/ClangBuiltLinux/linux/issues/2026 Fixes: f34907ecca71 ("mxser: Annotate struct mxser_board with __counted_by") Signed-off-by: Nathan Chancellor <nathan@kernel.org> Link: https://lore.kernel.org/r/20240529-drop-counted-by-ports-mxser-board-v1-1-0ab217f4da6d@kernel.org Signed-off-by: Kees Cook <kees@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 1c07c9be87dd3dd0634033bf08728b32465f08fb upstream.

Work for __counted_by on generic pointers in structures (not just
flexible array members) has started landing in Clang 19 (current tip of
tree). During the development of this feature, a restriction was added
to __counted_by to prevent the flexible array member's element type from
including a flexible array member itself such as:

  struct foo {
    int count;
    char buf[];
  };

  struct bar {
    int count;
    struct foo data[] __counted_by(count);
  };

because the size of data cannot be calculated with the standard array
size formula:

  sizeof(struct foo) * count

This restriction was downgraded to a warning but due to CONFIG_WERROR,
it can still break the build. The application of __counted_by on the
ports member of 'struct mxser_board' triggers this restriction,
resulting in:

  drivers/tty/mxser.c:291:2: error: 'counted_by' should not be applied to an array with element of unknown size because 'struct mxser_port' is a struct type with a flexible array member. This will be an error in a future compiler version [-Werror,-Wbounds-safety-counted-by-elt-type-unknown-size]
    291 |         struct mxser_port ports[] __counted_by(nports);
        |         ^~~~~~~~~~~~~~~~~~~~~~~~~
  1 error generated.

Remove this use of __counted_by to fix the warning/error. However,
rather than remove it altogether, leave it commented, as it may be
possible to support this in future compiler releases.

Cc:  <stable@vger.kernel.org>
Closes: https://github.com/ClangBuiltLinux/linux/issues/2026
Fixes: f34907ecca71 ("mxser: Annotate struct mxser_board with __counted_by")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20240529-drop-counted-by-ports-mxser-board-v1-1-0ab217f4da6d@kernel.org
Signed-off-by: Kees Cook <kees@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
serial: bcm63xx-uart: fix tx after conversion to uart_port_tx_limited() 2024-07-05T07:38:11+00:00 Jonas Gorski jonas.gorski@gmail.com 2024-06-06T19:56:33+00:00 3fea132e7d946e4c1e87c1e3ee00a64d92c1ef9c commit ea55c65dedf40e9c1911dc1e63e26bc9a59692b9 upstream. When bcm63xx-uart was converted to uart_port_tx_limited(), it implicitly added a call to stop_tx(). This causes garbage to be put out on the serial console. To fix this, pass UART_TX_NOSTOP in flags, and manually call stop_tx() ourselves analogue to how a similar issue was fixed in commit 7be50f2e8f20 ("serial: mxs-auart: fix tx"). Fixes: d11cc8c3c4b6 ("tty: serial: use uart_port_tx_limited()") Cc: stable@vger.kernel.org Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> Signed-off-by: Doug Brown <doug@schmorgal.com> Link: https://lore.kernel.org/r/20240606195632.173255-4-doug@schmorgal.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit ea55c65dedf40e9c1911dc1e63e26bc9a59692b9 upstream.

When bcm63xx-uart was converted to uart_port_tx_limited(), it implicitly
added a call to stop_tx(). This causes garbage to be put out on the
serial console. To fix this, pass UART_TX_NOSTOP in flags, and manually
call stop_tx() ourselves analogue to how a similar issue was fixed in
commit 7be50f2e8f20 ("serial: mxs-auart: fix tx").

Fixes: d11cc8c3c4b6 ("tty: serial: use uart_port_tx_limited()")
Cc: stable@vger.kernel.org
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: Doug Brown <doug@schmorgal.com>
Link: https://lore.kernel.org/r/20240606195632.173255-4-doug@schmorgal.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
serial: imx: set receiver level before starting uart 2024-07-05T07:38:10+00:00 Stefan Eichenberger stefan.eichenberger@toradex.com 2024-06-21T15:37:49+00:00 0d6d5bb896db119b1489735213805d1374fcffb9 commit a81dbd0463eca317eee44985a66aa6cc2ce5c101 upstream. Set the receiver level to something > 0 before calling imx_uart_start_rx in rs485_config. This is necessary to avoid an interrupt storm that might prevent the system from booting. This was seen on an i.MX7 device when the rs485-rts-active-low property was active in the device tree. Fixes: 6d215f83e5fc ("serial: imx: warn user when using unsupported configuration") Cc: stable <stable@kernel.org> Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com> Link: https://lore.kernel.org/r/20240621153829.183780-1-eichest@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit a81dbd0463eca317eee44985a66aa6cc2ce5c101 upstream.

Set the receiver level to something > 0 before calling imx_uart_start_rx
in rs485_config. This is necessary to avoid an interrupt storm that
might prevent the system from booting. This was seen on an i.MX7 device
when the rs485-rts-active-low property was active in the device tree.

Fixes: 6d215f83e5fc ("serial: imx: warn user when using unsupported configuration")
Cc: stable <stable@kernel.org>
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
Link: https://lore.kernel.org/r/20240621153829.183780-1-eichest@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
serial: 8250_omap: Implementation of Errata i2310 2024-07-05T07:38:10+00:00 Udit Kumar u-kumar1@ti.com 2024-06-19T10:59:03+00:00 6270051f656004ca5cde644c73cb1fa4d718792e commit 9d141c1e615795eeb93cd35501ad144ee997a826 upstream. As per Errata i2310[0], Erroneous timeout can be triggered, if this Erroneous interrupt is not cleared then it may leads to storm of interrupts, therefore apply Errata i2310 solution. [0] https://www.ti.com/lit/pdf/sprz536 page 23 Fixes: b67e830d38fa ("serial: 8250: 8250_omap: Fix possible interrupt storm on K3 SoCs") Cc: stable@vger.kernel.org Signed-off-by: Udit Kumar <u-kumar1@ti.com> Link: https://lore.kernel.org/r/20240619105903.165434-1-u-kumar1@ti.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 9d141c1e615795eeb93cd35501ad144ee997a826 upstream.

As per Errata i2310[0], Erroneous timeout can be triggered,
if this Erroneous interrupt is not cleared then it may leads
to storm of interrupts, therefore apply Errata i2310 solution.

[0] https://www.ti.com/lit/pdf/sprz536 page 23

Fixes: b67e830d38fa ("serial: 8250: 8250_omap: Fix possible interrupt storm on K3 SoCs")
Cc: stable@vger.kernel.org
Signed-off-by: Udit Kumar <u-kumar1@ti.com>
Link: https://lore.kernel.org/r/20240619105903.165434-1-u-kumar1@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tty: serial: 8250: Fix port count mismatch with the device 2024-07-05T07:38:10+00:00 Crescent Hsieh crescentcy.hsieh@moxa.com 2024-06-17T06:30:58+00:00 e3f0ca165f66d2252694d4b530c26900b69beef5 commit 0ac18dac43103ab1df6d26ec9a781c0126f83ced upstream. Normally, the number of ports is indicated by the third digit of the device ID on Moxa PCI serial boards. For example, `0x1121` indicates a device with 2 ports. However, `CP116E_A_A` and `CP116E_A_B` are exceptions; they have 8 ports, but the third digit of the device ID is `6`. This patch introduces a function to retrieve the number of ports on Moxa PCI serial boards, addressing the issue described above. Fixes: 37058fd5d239 ("tty: serial: 8250: Add support for MOXA Mini PCIe boards") Cc: stable <stable@kernel.org> Signed-off-by: Crescent Hsieh <crescentcy.hsieh@moxa.com> Reviewed-by: Andy Shevchenko <andy@kernel.org> Link: https://lore.kernel.org/r/20240617063058.18866-1-crescentcy.hsieh@moxa.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 0ac18dac43103ab1df6d26ec9a781c0126f83ced upstream.

Normally, the number of ports is indicated by the third digit of the
device ID on Moxa PCI serial boards. For example, `0x1121` indicates a
device with 2 ports.

However, `CP116E_A_A` and `CP116E_A_B` are exceptions; they have 8
ports, but the third digit of the device ID is `6`.

This patch introduces a function to retrieve the number of ports on Moxa
PCI serial boards, addressing the issue described above.

Fixes: 37058fd5d239 ("tty: serial: 8250: Add support for MOXA Mini PCIe boards")
Cc: stable <stable@kernel.org>
Signed-off-by: Crescent Hsieh <crescentcy.hsieh@moxa.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Link: https://lore.kernel.org/r/20240617063058.18866-1-crescentcy.hsieh@moxa.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
serial: 8250_dw: Revert "Move definitions to the shared header" 2024-06-27T11:52:30+00:00 Andy Shevchenko andriy.shevchenko@linux.intel.com 2024-05-14T19:05:54+00:00 2c48087fab46994ce0e33a186d1252a8f98592db commit 2c94512055f362dd789e0f87b8566feeddec83c9 upstream. This reverts commit d9666dfb314e1ffd6eb9c3c4243fe3e094c047a7. The container of the struct dw8250_port_data is private to the actual driver. In particular, 8250_lpss and 8250_dw use different data types that are assigned to the UART port private_data. Hence, it must not be used outside the specific driver. Fix the mistake made in the past by moving the respective definitions to the specific driver. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20240514190730.2787071-3-andriy.shevchenko@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 2c94512055f362dd789e0f87b8566feeddec83c9 upstream.

This reverts commit d9666dfb314e1ffd6eb9c3c4243fe3e094c047a7.

The container of the struct dw8250_port_data is private to the actual
driver. In particular, 8250_lpss and 8250_dw use different data types
that are assigned to the UART port private_data. Hence, it must not
be used outside the specific driver.

Fix the mistake made in the past by moving the respective definitions
to the specific driver.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240514190730.2787071-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>