linux-stable.git/drivers/tty, branch v6.12.35 Linux kernel stable tree serial: sh-sci: Increment the runtime usage counter for the earlycon device 2025-06-27T10:11:45+00:00 Claudiu Beznea claudiu.beznea.uj@bp.renesas.com 2025-01-16T18:22:49+00:00 977b7cc77852d1dea5b02e821c8841665097f246 commit 651dee03696e1dfde6d9a7e8664bbdcd9a10ea7f upstream. In the sh-sci driver, serial ports are mapped to the sci_ports[] array, with earlycon mapped at index zero. The uart_add_one_port() function eventually calls __device_attach(), which, in turn, calls pm_request_idle(). The identified code path is as follows: uart_add_one_port() -> serial_ctrl_register_port() -> serial_core_register_port() -> serial_core_port_device_add() -> serial_base_port_add() -> device_add() -> bus_probe_device() -> device_initial_probe() -> __device_attach() -> // ... if (dev->p->dead) { // ... } else if (dev->driver) { // ... } else { // ... pm_request_idle(dev); // ... } The earlycon device clocks are enabled by the bootloader. However, the pm_request_idle() call in __device_attach() disables the SCI port clocks while earlycon is still active. The earlycon write function, serial_console_write(), calls sci_poll_put_char() via serial_console_putchar(). If the SCI port clocks are disabled, writing to earlycon may sometimes cause the SR.TDFE bit to remain unset indefinitely, causing the while loop in sci_poll_put_char() to never exit. On single-core SoCs, this can result in the system being blocked during boot when this issue occurs. To resolve this, increment the runtime PM usage counter for the earlycon SCI device before registering the UART port. Fixes: 0b0cced19ab1 ("serial: sh-sci: Add CONFIG_SERIAL_EARLYCON support") Cc: stable@vger.kernel.org Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com> Link: https://lore.kernel.org/r/20250116182249.3828577-6-claudiu.beznea.uj@bp.renesas.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 651dee03696e1dfde6d9a7e8664bbdcd9a10ea7f upstream.

In the sh-sci driver, serial ports are mapped to the sci_ports[] array,
with earlycon mapped at index zero.

The uart_add_one_port() function eventually calls __device_attach(),
which, in turn, calls pm_request_idle(). The identified code path is as
follows:

uart_add_one_port() ->
  serial_ctrl_register_port() ->
    serial_core_register_port() ->
      serial_core_port_device_add() ->
        serial_base_port_add() ->
          device_add() ->
            bus_probe_device() ->
              device_initial_probe() ->
                __device_attach() ->
                  // ...
                  if (dev->p->dead) {
                    // ...
                  } else if (dev->driver) {
                    // ...
                  } else {
                    // ...
                    pm_request_idle(dev);
                    // ...
                  }

The earlycon device clocks are enabled by the bootloader. However, the
pm_request_idle() call in __device_attach() disables the SCI port clocks
while earlycon is still active.

The earlycon write function, serial_console_write(), calls
sci_poll_put_char() via serial_console_putchar(). If the SCI port clocks
are disabled, writing to earlycon may sometimes cause the SR.TDFE bit to
remain unset indefinitely, causing the while loop in sci_poll_put_char()
to never exit. On single-core SoCs, this can result in the system being
blocked during boot when this issue occurs.

To resolve this, increment the runtime PM usage counter for the earlycon
SCI device before registering the UART port.

Fixes: 0b0cced19ab1 ("serial: sh-sci: Add CONFIG_SERIAL_EARLYCON support")
Cc: stable@vger.kernel.org
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://lore.kernel.org/r/20250116182249.3828577-6-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
serial: sh-sci: Clean sci_ports[0] after at earlycon exit 2025-06-27T10:11:45+00:00 Claudiu Beznea claudiu.beznea.uj@bp.renesas.com 2025-01-16T18:22:48+00:00 966dbf35e36f81541d0ba69d24a5131109fcbb5e commit 5f1017069933489add0c08659673443c9905659e upstream. The early_console_setup() function initializes sci_ports[0].port with an object of type struct uart_port obtained from the struct earlycon_device passed as an argument to early_console_setup(). Later, during serial port probing, the serial port used as earlycon (e.g., port A) might be remapped to a different position in the sci_ports[] array, and a different serial port (e.g., port B) might be assigned to slot 0. For example: sci_ports[0] = port B sci_ports[X] = port A In this scenario, the new port mapped at index zero (port B) retains the data associated with the earlycon configuration. Consequently, after the Linux boot process, any access to the serial port now mapped to sci_ports[0] (port B) will block the original earlycon port (port A). To address this, introduce an early_console_exit() function to clean up sci_ports[0] when earlycon is exited. To prevent the cleanup of sci_ports[0] while the serial device is still being used by earlycon, introduce the struct sci_port::probing flag and account for it in early_console_exit(). Fixes: 0b0cced19ab1 ("serial: sh-sci: Add CONFIG_SERIAL_EARLYCON support") Cc: stable@vger.kernel.org Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com> Link: https://lore.kernel.org/r/20250116182249.3828577-5-claudiu.beznea.uj@bp.renesas.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 5f1017069933489add0c08659673443c9905659e upstream.

The early_console_setup() function initializes sci_ports[0].port with an
object of type struct uart_port obtained from the struct earlycon_device
passed as an argument to early_console_setup().

Later, during serial port probing, the serial port used as earlycon
(e.g., port A) might be remapped to a different position in the sci_ports[]
array, and a different serial port (e.g., port B) might be assigned to slot
0. For example:

sci_ports[0] = port B
sci_ports[X] = port A

In this scenario, the new port mapped at index zero (port B) retains the
data associated with the earlycon configuration. Consequently, after the
Linux boot process, any access to the serial port now mapped to
sci_ports[0] (port B) will block the original earlycon port (port A).

To address this, introduce an early_console_exit() function to clean up
sci_ports[0] when earlycon is exited.

To prevent the cleanup of sci_ports[0] while the serial device is still
being used by earlycon, introduce the struct sci_port::probing flag and
account for it in early_console_exit().

Fixes: 0b0cced19ab1 ("serial: sh-sci: Add CONFIG_SERIAL_EARLYCON support")
Cc: stable@vger.kernel.org
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://lore.kernel.org/r/20250116182249.3828577-5-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tty: serial: 8250_omap: fix TX with DMA for am33xx 2025-06-19T13:32:35+00:00 Jiri Slaby (SUSE) jirislaby@kernel.org 2025-05-22T05:38:35+00:00 393abb68b9ecc78f5ae9bc2898c3325427cd8e1d commit b495021a973e2468497689bd3e29b736747b896f upstream. Commit 1788cf6a91d9 ("tty: serial: switch from circ_buf to kfifo") introduced an error in the TX DMA handling for 8250_omap. When the OMAP_DMA_TX_KICK flag is set, the "skip_byte" is pulled from the kfifo and emitted directly in order to start the DMA. While the kfifo is updated, dma->tx_size is not decreased. This leads to uart_xmit_advance() called in omap_8250_dma_tx_complete() advancing the kfifo by one too much. In practice, transmitting N bytes has been seen to result in the last N-1 bytes being sent repeatedly. This change fixes the problem by moving all of the dma setup after the OMAP_DMA_TX_KICK handling and using kfifo_len() instead of the DMA size for the 4-byte cutoff check. This slightly changes the behaviour at buffer wraparound, but it still transmits the correct bytes somehow. Now, the "skip_byte" would no longer be accounted to the stats. As previously, dma->tx_size included also this skip byte, up->icount.tx was updated by aforementioned uart_xmit_advance() in omap_8250_dma_tx_complete(). Fix this by using the uart_fifo_out() helper instead of bare kfifo_get(). Based on patch by Mans Rullgard <mans@mansr.com> Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org> Fixes: 1788cf6a91d9 ("tty: serial: switch from circ_buf to kfifo") Link: https://lore.kernel.org/all/20250506150748.3162-1-mans@mansr.com/ Reported-by: Mans Rullgard <mans@mansr.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20250522053835.3495975-1-jirislaby@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit b495021a973e2468497689bd3e29b736747b896f upstream.

Commit 1788cf6a91d9 ("tty: serial: switch from circ_buf to kfifo")
introduced an error in the TX DMA handling for 8250_omap.

When the OMAP_DMA_TX_KICK flag is set, the "skip_byte" is pulled from
the kfifo and emitted directly in order to start the DMA. While the
kfifo is updated, dma->tx_size is not decreased. This leads to
uart_xmit_advance() called in omap_8250_dma_tx_complete() advancing the
kfifo by one too much.

In practice, transmitting N bytes has been seen to result in the last
N-1 bytes being sent repeatedly.

This change fixes the problem by moving all of the dma setup after the
OMAP_DMA_TX_KICK handling and using kfifo_len() instead of the DMA size
for the 4-byte cutoff check. This slightly changes the behaviour at
buffer wraparound, but it still transmits the correct bytes somehow.

Now, the "skip_byte" would no longer be accounted to the stats. As
previously, dma->tx_size included also this skip byte, up->icount.tx was
updated by aforementioned uart_xmit_advance() in
omap_8250_dma_tx_complete(). Fix this by using the uart_fifo_out()
helper instead of bare kfifo_get().

Based on patch by Mans Rullgard <mans@mansr.com>

Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Fixes: 1788cf6a91d9 ("tty: serial: switch from circ_buf to kfifo")
Link: https://lore.kernel.org/all/20250506150748.3162-1-mans@mansr.com/
Reported-by: Mans Rullgard <mans@mansr.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20250522053835.3495975-1-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
serial: sh-sci: Move runtime PM enable to sci_probe_single() 2025-06-19T13:32:24+00:00 Claudiu Beznea claudiu.beznea.uj@bp.renesas.com 2025-01-16T18:22:46+00:00 21b2bca88e17a5a62c6399f3501d6c51e7259571 [ Upstream commit 239f11209e5f282e16f5241b99256e25dd0614b6 ] Relocate the runtime PM enable operation to sci_probe_single(). This change prepares the codebase for upcoming fixes. While at it, replace the existing logic with a direct call to devm_pm_runtime_enable() and remove sci_cleanup_single(). The devm_pm_runtime_enable() function automatically handles disabling runtime PM during driver removal. Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com> Link: https://lore.kernel.org/r/20250116182249.3828577-3-claudiu.beznea.uj@bp.renesas.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit 239f11209e5f282e16f5241b99256e25dd0614b6 ]

Relocate the runtime PM enable operation to sci_probe_single(). This change
prepares the codebase for upcoming fixes.

While at it, replace the existing logic with a direct call to
devm_pm_runtime_enable() and remove sci_cleanup_single(). The
devm_pm_runtime_enable() function automatically handles disabling runtime
PM during driver removal.

Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://lore.kernel.org/r/20250116182249.3828577-3-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
vt: remove VT_RESIZE and VT_RESIZEX from vt_compat_ioctl() 2025-06-19T13:32:13+00:00 Nicolas Pitre npitre@baylibre.com 2025-05-15T15:30:52+00:00 130e134f6ecaa61e3b7db13b0f41e5a98e8aca93 [ Upstream commit c4c7ead7b86c1e7f11c64915b7e5bb6d2e242691 ] They are listed amon those cmd values that "treat 'arg' as an integer" which is wrong. They should instead fall into the default case. Probably nobody ever relied on that code since 2009 but still. Fixes: e92166517e3c ("tty: handle VT specific compat ioctls in vt driver") Signed-off-by: Nicolas Pitre <npitre@baylibre.com> Reviewed-by: Jiri Slaby <jirislaby@kernel.org> Link: https://lore.kernel.org/r/pr214s15-36r8-6732-2pop-159nq85o48r7@syhkavp.arg Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit c4c7ead7b86c1e7f11c64915b7e5bb6d2e242691 ]

They are listed amon those cmd values that "treat 'arg' as an integer"
which is wrong. They should instead fall into the default case. Probably
nobody ever relied on that code since 2009 but still.

Fixes: e92166517e3c ("tty: handle VT specific compat ioctls in vt driver")
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/pr214s15-36r8-6732-2pop-159nq85o48r7@syhkavp.arg
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
serial: Fix potential null-ptr-deref in mlb_usio_probe() 2025-06-19T13:32:11+00:00 Henry Martin bsdhenrymartin@gmail.com 2025-04-03T07:03:39+00:00 c23d87b43f7dba5eb12820f6cf21a1cd4f63eb3d [ Upstream commit 86bcae88c9209e334b2f8c252f4cc66beb261886 ] devm_ioremap() can return NULL on error. Currently, mlb_usio_probe() does not check for this case, which could result in a NULL pointer dereference. Add NULL check after devm_ioremap() to prevent this issue. Fixes: ba44dc043004 ("serial: Add Milbeaut serial control") Signed-off-by: Henry Martin <bsdhenrymartin@gmail.com> Link: https://lore.kernel.org/r/20250403070339.64990-1-bsdhenrymartin@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit 86bcae88c9209e334b2f8c252f4cc66beb261886 ]

devm_ioremap() can return NULL on error. Currently, mlb_usio_probe()
does not check for this case, which could result in a NULL pointer
dereference.

Add NULL check after devm_ioremap() to prevent this issue.

Fixes: ba44dc043004 ("serial: Add Milbeaut serial control")
Signed-off-by: Henry Martin <bsdhenrymartin@gmail.com>
Link: https://lore.kernel.org/r/20250403070339.64990-1-bsdhenrymartin@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
serial: jsm: fix NPE during jsm_uart_port_init 2025-06-10T11:13:00+00:00 Dustin Lundquist dustin@null-ptr.net 2025-05-06T18:18:45+00:00 985961dd2688a527a4847300d41beaad475ab7af commit e3975aa899c0a3bbc10d035e699b142cd1373a71 upstream. No device was set which caused serial_base_ctrl_add to crash. BUG: kernel NULL pointer dereference, address: 0000000000000050 Oops: Oops: 0000 [#1] PREEMPT SMP NOPTI CPU: 16 UID: 0 PID: 368 Comm: (udev-worker) Not tainted 6.12.25-amd64 #1 Debian 6.12.25-1 RIP: 0010:serial_base_ctrl_add+0x96/0x120 Call Trace: <TASK> serial_core_register_port+0x1a0/0x580 ? __setup_irq+0x39c/0x660 ? __kmalloc_cache_noprof+0x111/0x310 jsm_uart_port_init+0xe8/0x180 [jsm] jsm_probe_one+0x1f4/0x410 [jsm] local_pci_probe+0x42/0x90 pci_device_probe+0x22f/0x270 really_probe+0xdb/0x340 ? pm_runtime_barrier+0x54/0x90 ? __pfx___driver_attach+0x10/0x10 __driver_probe_device+0x78/0x110 driver_probe_device+0x1f/0xa0 __driver_attach+0xba/0x1c0 bus_for_each_dev+0x8c/0xe0 bus_add_driver+0x112/0x1f0 driver_register+0x72/0xd0 jsm_init_module+0x36/0xff0 [jsm] ? __pfx_jsm_init_module+0x10/0x10 [jsm] do_one_initcall+0x58/0x310 do_init_module+0x60/0x230 Tested with Digi Neo PCIe 8 port card. Fixes: 84a9582fd203 ("serial: core: Start managing serial controllers to enable runtime PM") Cc: stable <stable@kernel.org> Signed-off-by: Dustin Lundquist <dustin@null-ptr.net> Link: https://lore.kernel.org/r/3f31d4f75863614655c4673027a208be78d022ec.camel@null-ptr.net Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit e3975aa899c0a3bbc10d035e699b142cd1373a71 upstream.

No device was set which caused serial_base_ctrl_add to crash.

 BUG: kernel NULL pointer dereference, address: 0000000000000050
 Oops: Oops: 0000 [#1] PREEMPT SMP NOPTI
 CPU: 16 UID: 0 PID: 368 Comm: (udev-worker) Not tainted 6.12.25-amd64 #1  Debian 6.12.25-1
 RIP: 0010:serial_base_ctrl_add+0x96/0x120
 Call Trace:
  <TASK>
  serial_core_register_port+0x1a0/0x580
  ? __setup_irq+0x39c/0x660
  ? __kmalloc_cache_noprof+0x111/0x310
  jsm_uart_port_init+0xe8/0x180 [jsm]
  jsm_probe_one+0x1f4/0x410 [jsm]
  local_pci_probe+0x42/0x90
  pci_device_probe+0x22f/0x270
  really_probe+0xdb/0x340
  ? pm_runtime_barrier+0x54/0x90
  ? __pfx___driver_attach+0x10/0x10
  __driver_probe_device+0x78/0x110
  driver_probe_device+0x1f/0xa0
  __driver_attach+0xba/0x1c0
  bus_for_each_dev+0x8c/0xe0
  bus_add_driver+0x112/0x1f0
  driver_register+0x72/0xd0
  jsm_init_module+0x36/0xff0 [jsm]
  ? __pfx_jsm_init_module+0x10/0x10 [jsm]
  do_one_initcall+0x58/0x310
  do_init_module+0x60/0x230

Tested with Digi Neo PCIe 8 port card.

Fixes: 84a9582fd203 ("serial: core: Start managing serial controllers to enable runtime PM")
Cc: stable <stable@kernel.org>
Signed-off-by: Dustin Lundquist <dustin@null-ptr.net>
Link: https://lore.kernel.org/r/3f31d4f75863614655c4673027a208be78d022ec.camel@null-ptr.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
serial: sh-sci: Save and restore more registers 2025-05-29T09:03:26+00:00 Geert Uytterhoeven geert+renesas@glider.be 2025-03-04T19:06:11+00:00 a8a34fbf915dd5c472ada04e7c969da65f7d693a commit 81100b9a7b0515132996d62a7a676a77676cb6e3 upstream. On (H)SCIF with a Baud Rate Generator for External Clock (BRG), there are multiple ways to configure the requested serial speed. If firmware uses a different method than Linux, and if any debug info is printed after the Bit Rate Register (SCBRR) is restored, but before termios is reconfigured (which configures the alternative method), the system may lock-up during resume. Fix this by saving and restoring the contents of the BRG Frequency Division (SCDL) and Clock Select (SCCKS) registers as well. Also save and restore the HSCIF's Sampling Rate Register (HSSRR), which configures the sampling point, and the SCIFA/SCIFB's Serial Port Control and Data Registers (SCPCR/SCPDR), which configure the optional control flow signals. After this, all registers that are not saved/restored are either: - read-only, - write-only, - status registers containing flags with clear-after-set semantics, - FIFO Data Count Trigger registers, which do not matter much for the serial console. Fixes: 22a6984c5b5df8ea ("serial: sh-sci: Update the suspend/resume support") Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Tested-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com> Reviewed-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com> Link: https://lore.kernel.org/r/11c2eab45d48211e75d8b8202cce60400880fe55.1741114989.git.geert+renesas@glider.be Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 81100b9a7b0515132996d62a7a676a77676cb6e3 upstream.

On (H)SCIF with a Baud Rate Generator for External Clock (BRG), there
are multiple ways to configure the requested serial speed.  If firmware
uses a different method than Linux, and if any debug info is printed
after the Bit Rate Register (SCBRR) is restored, but before termios is
reconfigured (which configures the alternative method), the system may
lock-up during resume.

Fix this by saving and restoring the contents of the BRG Frequency
Division (SCDL) and Clock Select (SCCKS) registers as well.

Also save and restore the HSCIF's Sampling Rate Register (HSSRR), which
configures the sampling point, and the SCIFA/SCIFB's Serial Port Control
and Data Registers (SCPCR/SCPDR), which configure the optional control
flow signals.

After this, all registers that are not saved/restored are either:
  - read-only,
  - write-only,
  - status registers containing flags with clear-after-set semantics,
  - FIFO Data Count Trigger registers, which do not matter much for
    the serial console.

Fixes: 22a6984c5b5df8ea ("serial: sh-sci: Update the suspend/resume support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://lore.kernel.org/r/11c2eab45d48211e75d8b8202cce60400880fe55.1741114989.git.geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
serial: sh-sci: Update the suspend/resume support 2025-05-29T09:02:51+00:00 Claudiu Beznea claudiu.beznea.uj@bp.renesas.com 2025-02-07T11:33:13+00:00 5de11f82cbfd17be1f3d36a15d54396206eccf11 [ Upstream commit 22a6984c5b5df8eab864d7f3e8b94d5a554d31ab ] The Renesas RZ/G3S supports a power saving mode where power to most of the SoC components is turned off. When returning from this power saving mode, SoC components need to be re-configured. The SCIFs on the Renesas RZ/G3S need to be re-configured as well when returning from this power saving mode. The sh-sci code already configures the SCIF clocks, power domain and registers by calling uart_resume_port() in sci_resume(). On suspend path the SCIF UART ports are suspended accordingly (by calling uart_suspend_port() in sci_suspend()). The only missing setting is the reset signal. For this assert/de-assert the reset signal on driver suspend/resume. In case the no_console_suspend is specified by the user, the registers need to be saved on suspend path and restore on resume path. To do this the sci_console_save()/sci_console_restore() functions were added. There is no need to cache/restore the status or FIFO registers. Only the control registers. The registers that will be saved/restored on suspend/resume are specified by the struct sci_suspend_regs data structure. Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Link: https://lore.kernel.org/r/20250207113313.545432-1-claudiu.beznea.uj@bp.renesas.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit 22a6984c5b5df8eab864d7f3e8b94d5a554d31ab ]

The Renesas RZ/G3S supports a power saving mode where power to most of the
SoC components is turned off. When returning from this power saving mode,
SoC components need to be re-configured.

The SCIFs on the Renesas RZ/G3S need to be re-configured as well when
returning from this power saving mode. The sh-sci code already configures
the SCIF clocks, power domain and registers by calling uart_resume_port()
in sci_resume(). On suspend path the SCIF UART ports are suspended
accordingly (by calling uart_suspend_port() in sci_suspend()). The only
missing setting is the reset signal. For this assert/de-assert the reset
signal on driver suspend/resume.

In case the no_console_suspend is specified by the user, the registers need
to be saved on suspend path and restore on resume path. To do this the
sci_console_save()/sci_console_restore() functions were added. There is no
need to cache/restore the status or FIFO registers. Only the control
registers. The registers that will be saved/restored on suspend/resume are
specified by the struct sci_suspend_regs data structure.

Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20250207113313.545432-1-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
serial: mctrl_gpio: split disable_ms into sync and no_sync APIs 2025-05-29T09:02:45+00:00 Alexis Lothoré alexis.lothore@bootlin.com 2025-02-17T06:21:53+00:00 e6a46719a2369eb5186d4f7e6c0478720ca1ec3d [ Upstream commit 1bd2aad57da95f7f2d2bb52f7ad15c0f4993a685 ] The following splat has been observed on a SAMA5D27 platform using atmel_serial: BUG: sleeping function called from invalid context at kernel/irq/manage.c:738 in_atomic(): 1, irqs_disabled(): 128, non_block: 0, pid: 27, name: kworker/u5:0 preempt_count: 1, expected: 0 INFO: lockdep is turned off. irq event stamp: 0 hardirqs last enabled at (0): [<00000000>] 0x0 hardirqs last disabled at (0): [<c01588f0>] copy_process+0x1c4c/0x7bec softirqs last enabled at (0): [<c0158944>] copy_process+0x1ca0/0x7bec softirqs last disabled at (0): [<00000000>] 0x0 CPU: 0 UID: 0 PID: 27 Comm: kworker/u5:0 Not tainted 6.13.0-rc7+ #74 Hardware name: Atmel SAMA5 Workqueue: hci0 hci_power_on [bluetooth] Call trace: unwind_backtrace from show_stack+0x18/0x1c show_stack from dump_stack_lvl+0x44/0x70 dump_stack_lvl from __might_resched+0x38c/0x598 __might_resched from disable_irq+0x1c/0x48 disable_irq from mctrl_gpio_disable_ms+0x74/0xc0 mctrl_gpio_disable_ms from atmel_disable_ms.part.0+0x80/0x1f4 atmel_disable_ms.part.0 from atmel_set_termios+0x764/0x11e8 atmel_set_termios from uart_change_line_settings+0x15c/0x994 uart_change_line_settings from uart_set_termios+0x2b0/0x668 uart_set_termios from tty_set_termios+0x600/0x8ec tty_set_termios from ttyport_set_flow_control+0x188/0x1e0 ttyport_set_flow_control from wilc_setup+0xd0/0x524 [hci_wilc] wilc_setup [hci_wilc] from hci_dev_open_sync+0x330/0x203c [bluetooth] hci_dev_open_sync [bluetooth] from hci_dev_do_open+0x40/0xb0 [bluetooth] hci_dev_do_open [bluetooth] from hci_power_on+0x12c/0x664 [bluetooth] hci_power_on [bluetooth] from process_one_work+0x998/0x1a38 process_one_work from worker_thread+0x6e0/0xfb4 worker_thread from kthread+0x3d4/0x484 kthread from ret_from_fork+0x14/0x28 This warning is emitted when trying to toggle, at the highest level, some flow control (with serdev_device_set_flow_control) in a device driver. At the lowest level, the atmel_serial driver is using serial_mctrl_gpio lib to enable/disable the corresponding IRQs accordingly. The warning emitted by CONFIG_DEBUG_ATOMIC_SLEEP is due to disable_irq (called in mctrl_gpio_disable_ms) being possibly called in some atomic context (some tty drivers perform modem lines configuration in regions protected by port lock). Split mctrl_gpio_disable_ms into two differents APIs, a non-blocking one and a blocking one. Replace mctrl_gpio_disable_ms calls with the relevant version depending on whether the call is protected by some port lock. Suggested-by: Jiri Slaby <jirislaby@kernel.org> Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com> Acked-by: Richard Genoud <richard.genoud@bootlin.com> Link: https://lore.kernel.org/r/20250217-atomic_sleep_mctrl_serial_gpio-v3-1-59324b313eef@bootlin.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit 1bd2aad57da95f7f2d2bb52f7ad15c0f4993a685 ]

The following splat has been observed on a SAMA5D27 platform using
atmel_serial:

BUG: sleeping function called from invalid context at kernel/irq/manage.c:738
in_atomic(): 1, irqs_disabled(): 128, non_block: 0, pid: 27, name: kworker/u5:0
preempt_count: 1, expected: 0
INFO: lockdep is turned off.
irq event stamp: 0
hardirqs last  enabled at (0): [<00000000>] 0x0
hardirqs last disabled at (0): [<c01588f0>] copy_process+0x1c4c/0x7bec
softirqs last  enabled at (0): [<c0158944>] copy_process+0x1ca0/0x7bec
softirqs last disabled at (0): [<00000000>] 0x0
CPU: 0 UID: 0 PID: 27 Comm: kworker/u5:0 Not tainted 6.13.0-rc7+ #74
Hardware name: Atmel SAMA5
Workqueue: hci0 hci_power_on [bluetooth]
Call trace:
  unwind_backtrace from show_stack+0x18/0x1c
  show_stack from dump_stack_lvl+0x44/0x70
  dump_stack_lvl from __might_resched+0x38c/0x598
  __might_resched from disable_irq+0x1c/0x48
  disable_irq from mctrl_gpio_disable_ms+0x74/0xc0
  mctrl_gpio_disable_ms from atmel_disable_ms.part.0+0x80/0x1f4
  atmel_disable_ms.part.0 from atmel_set_termios+0x764/0x11e8
  atmel_set_termios from uart_change_line_settings+0x15c/0x994
  uart_change_line_settings from uart_set_termios+0x2b0/0x668
  uart_set_termios from tty_set_termios+0x600/0x8ec
  tty_set_termios from ttyport_set_flow_control+0x188/0x1e0
  ttyport_set_flow_control from wilc_setup+0xd0/0x524 [hci_wilc]
  wilc_setup [hci_wilc] from hci_dev_open_sync+0x330/0x203c [bluetooth]
  hci_dev_open_sync [bluetooth] from hci_dev_do_open+0x40/0xb0 [bluetooth]
  hci_dev_do_open [bluetooth] from hci_power_on+0x12c/0x664 [bluetooth]
  hci_power_on [bluetooth] from process_one_work+0x998/0x1a38
  process_one_work from worker_thread+0x6e0/0xfb4
  worker_thread from kthread+0x3d4/0x484
  kthread from ret_from_fork+0x14/0x28

This warning is emitted when trying to toggle, at the highest level,
some flow control (with serdev_device_set_flow_control) in a device
driver. At the lowest level, the atmel_serial driver is using
serial_mctrl_gpio lib to enable/disable the corresponding IRQs
accordingly.  The warning emitted by CONFIG_DEBUG_ATOMIC_SLEEP is due to
disable_irq (called in mctrl_gpio_disable_ms) being possibly called in
some atomic context (some tty drivers perform modem lines configuration
in regions protected by port lock).

Split mctrl_gpio_disable_ms into two differents APIs, a non-blocking one
and a blocking one. Replace mctrl_gpio_disable_ms calls with the
relevant version depending on whether the call is protected by some port
lock.

Suggested-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Acked-by: Richard Genoud <richard.genoud@bootlin.com>
Link: https://lore.kernel.org/r/20250217-atomic_sleep_mctrl_serial_gpio-v3-1-59324b313eef@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>