linux-stable.git/drivers/tty, branch v5.4.197

tty/serial: digicolor: fix possible null-ptr-deref in digicolor_uart_probe()

2022-05-18T07:47:28+00:00

commit 447ee1516f19f534a228dda237eddb202f23e163 upstream.

It will cause null-ptr-deref when using 'res', if platform_get_resource()
returns NULL, so move using 'res' after devm_ioremap_resource() that
will check it to avoid null-ptr-deref.
And use devm_platform_get_and_ioremap_resource() to simplify code.

Fixes: 5930cb3511df ("serial: driver for Conexant Digicolor USART")
Signed-off-by: Yang Yingliang 
Reviewed-by: Baruch Siach 
Cc: stable 
Link: https://lore.kernel.org/r/20220505124621.1592697-1-yangyingliang@huawei.com
Signed-off-by: Greg Kroah-Hartman

serial: 8250_mtk: Fix register address for XON/XOFF character

2022-05-18T07:47:27+00:00

commit e1bfdbc7daca171c74a577b3dd0b36d76bb0ffcc upstream.

The XON1/XOFF1 character registers are at offset 0xa0 and 0xa8
respectively, so we cannot use the definition in serial_port.h.

Fixes: bdbd0a7f8f03 ("serial: 8250-mtk: modify baudrate setting")
Signed-off-by: AngeloGioacchino Del Regno 
Cc: stable 
Link: https://lore.kernel.org/r/20220427132328.228297-4-angelogioacchino.delregno@collabora.com
Signed-off-by: Greg Kroah-Hartman

serial: 8250_mtk: Fix UART_EFR register address

2022-05-18T07:47:27+00:00

commit bb0b197aadd928f52ce6f01f0ee977f0a08cf1be upstream.

On MediaTek SoCs, the UART IP is 16550A compatible, but there are some
specific quirks: we are declaring a register shift of 2, but this is
only valid for the majority of the registers, as there are some that
are out of the standard layout.

Specifically, this driver is using definitions from serial_reg.h, where
we have a UART_EFR register defined as 2: this results in a 0x8 offset,
but there we have the FCR register instead.

The right offset for the EFR register on MediaTek UART is at 0x98,
so, following the decimal definition convention in serial_reg.h and
accounting for the register left shift of two, add and use the correct
register address for this IP, defined as decimal 38, so that the final
calculation results in (0x26 << 2) = 0x98.

Fixes: bdbd0a7f8f03 ("serial: 8250-mtk: modify baudrate setting")
Signed-off-by: AngeloGioacchino Del Regno 
Cc: stable 
Link: https://lore.kernel.org/r/20220427132328.228297-2-angelogioacchino.delregno@collabora.com
Signed-off-by: Greg Kroah-Hartman

tty: n_gsm: fix mux activation issues in gsm_config()

2022-05-18T07:47:26+00:00

commit edd5f60c340086891fab094ad61270d6c80f9ca4 upstream.

The current implementation activates the mux if it was restarted and opens
the control channel if the mux was previously closed and we are now acting
as initiator instead of responder, which is the default setting.
This has two issues.
1) No mux is activated if we keep all default values and only switch to
initiator. The control channel is not allocated but will be opened next
which results in a NULL pointer dereference.
2) Switching the configuration after it was once configured while keeping
the initiator value the same will not reopen the control channel if it was
closed due to parameter incompatibilities. The mux remains dead.

Fix 1) by always activating the mux if it is dead after configuration.
Fix 2) by always opening the control channel after mux activation.

Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke 
Link: https://lore.kernel.org/r/20220504081733.3494-2-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman

tty: n_gsm: fix incorrect UA handling

2022-05-09T07:03:27+00:00

commit ff9166c623704337bd6fe66fce2838d9768a6634 upstream.

n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.4.4.2 states that any received unnumbered
acknowledgment (UA) with its poll/final (PF) bit set to 0 shall be
discarded. Currently, all UA frame are handled in the same way regardless
of the PF bit. This does not comply with the standard.
Remove the UA case in gsm_queue() to process only UA frames with PF bit set
to 1 to abide the standard.

Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke 
Link: https://lore.kernel.org/r/20220414094225.4527-20-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman

tty: n_gsm: fix wrong command frame length field encoding

2022-05-09T07:03:27+00:00

commit 398867f59f956985f4c324f173eff7b946e14bd8 upstream.

n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.4.6.1 states that each command frame shall
be made up from type, length and value. Looking for example in chapter
5.4.6.3.5 at the description for the encoding of a flow control on command
it becomes obvious, that the type and length field is always present
whereas the value may be zero bytes long. The current implementation omits
the length field if the value is not present. This is wrong.
Correct this by always sending the length in gsm_control_transmit().
So far only the modem status command (MSC) has included a value and encoded
its length directly. Therefore, also change gsmtty_modem_update().

Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke 
Link: https://lore.kernel.org/r/20220414094225.4527-12-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman

tty: n_gsm: fix wrong command retry handling

2022-05-09T07:03:27+00:00

commit d0bcdffcad5a22f202e3bf37190c0dd8c080ea92 upstream.

n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.7.3 states that the valid range for the
maximum number of retransmissions (N2) is from 0 to 255 (both including).
gsm_config() fails to limit this range correctly. Furthermore,
gsm_control_retransmit() handles this number incorrectly by performing
N2 - 1 retransmission attempts. Setting N2 to zero results in more than 255
retransmission attempts.
Fix the range check in gsm_config() and the value handling in
gsm_control_send() and gsm_control_retransmit() to comply with 3GPP 27.010.

Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke 
Link: https://lore.kernel.org/r/20220414094225.4527-11-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman

tty: n_gsm: fix missing explicit ldisc flush

2022-05-09T07:03:27+00:00

commit 17eac652028501df7ea296b1d9b9c134db262b7d upstream.

In gsm_cleanup_mux() the muxer is closed down and all queues are removed.
However, removing the queues is done without explicit control of the
underlying buffers. Flush those before freeing up our queues to ensure
that all outgoing queues are cleared consistently. Otherwise, a new mux
connection establishment attempt may time out while the underlying tty is
still busy sending out the remaining data from the previous connection.

Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke 
Link: https://lore.kernel.org/r/20220414094225.4527-10-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman

tty: n_gsm: fix insufficient txframe size

2022-05-09T07:03:27+00:00

commit 535bf600de75a859698892ee873521a48d289ec1 upstream.

n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.7.2 states that the maximum frame size
(N1) refers to the length of the information field (i.e. user payload).
However, 'txframe' stores the whole frame including frame header, checksum
and start/end flags. We also need to consider the byte stuffing overhead.
Define constant for the protocol overhead and adjust the 'txframe' size
calculation accordingly to reserve enough space for a complete mux frame
including byte stuffing for advanced option mode. Note that no byte
stuffing is applied to the start and end flag.
Also use MAX_MTU instead of MAX_MRU as this buffer is used for data
transmission.

Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke 
Link: https://lore.kernel.org/r/20220414094225.4527-8-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman

tty: n_gsm: fix malformed counter for out of frame data

2022-05-09T07:03:27+00:00

commit a24b4b2f660b7ddf3f484b37600bba382cb28a9d upstream.

The gsm_mux field 'malformed' represents the number of malformed frames
received. However, gsm1_receive() also increases this counter for any out
of frame byte.
Fix this by ignoring out of frame data for the malformed counter.

Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke 
Link: https://lore.kernel.org/r/20220414094225.4527-7-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman