linux-stable.git/drivers/tty, branch v5.4.161 Linux kernel stable tree serial: xilinx_uartps: Fix race condition causing stuck TX 2021-11-17T08:48:43+00:00 Anssi Hannula anssi.hannula@bitwise.fi 2021-10-26T10:27:41+00:00 fae0552d83ff44fd225ae3de1297d6075f1c652b [ Upstream commit 88b20f84f0fe47409342669caf3e58a3fc64c316 ] xilinx_uartps .start_tx() clears TXEMPTY when enabling TXEMPTY to avoid any previous TXEVENT event asserting the UART interrupt. This clear operation is done immediately after filling the TX FIFO. However, if the bytes inserted by cdns_uart_handle_tx() are consumed by the UART before the TXEMPTY is cleared, the clear operation eats the new TXEMPTY event as well, causing cdns_uart_isr() to never receive the TXEMPTY event. If there are bytes still queued in circbuf, TX will get stuck as they will never get transferred to FIFO (unless new bytes are queued to circbuf in which case .start_tx() is called again). While the racy missed TXEMPTY occurs fairly often with short data sequences (e.g. write 1 byte), in those cases circbuf is usually empty so no action on TXEMPTY would have been needed anyway. On the other hand, longer data sequences make the race much more unlikely as UART takes longer to consume the TX FIFO. Therefore it is rare for this race to cause visible issues in general. Fix the race by clearing the TXEMPTY bit in ISR *before* filling the FIFO. The TXEMPTY bit in ISR will only get asserted at the exact moment the TX FIFO *becomes* empty, so clearing the bit before filling FIFO does not cause an extra immediate assertion even if the FIFO is initially empty. This is hard to reproduce directly on a normal system, but inserting e.g. udelay(200) after cdns_uart_handle_tx(port), setting 4000000 baud, and then running "dd if=/dev/zero bs=128 of=/dev/ttyPS0 count=50" reliably reproduces the issue on my ZynqMP test system unless this fix is applied. Fixes: 85baf542d54e ("tty: xuartps: support 64 byte FIFO size") Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi> Link: https://lore.kernel.org/r/20211026102741.2910441-1-anssi.hannula@bitwise.fi Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit 88b20f84f0fe47409342669caf3e58a3fc64c316 ]

xilinx_uartps .start_tx() clears TXEMPTY when enabling TXEMPTY to avoid
any previous TXEVENT event asserting the UART interrupt. This clear
operation is done immediately after filling the TX FIFO.

However, if the bytes inserted by cdns_uart_handle_tx() are consumed by
the UART before the TXEMPTY is cleared, the clear operation eats the new
TXEMPTY event as well, causing cdns_uart_isr() to never receive the
TXEMPTY event. If there are bytes still queued in circbuf, TX will get
stuck as they will never get transferred to FIFO (unless new bytes are
queued to circbuf in which case .start_tx() is called again).

While the racy missed TXEMPTY occurs fairly often with short data
sequences (e.g. write 1 byte), in those cases circbuf is usually empty
so no action on TXEMPTY would have been needed anyway. On the other
hand, longer data sequences make the race much more unlikely as UART
takes longer to consume the TX FIFO. Therefore it is rare for this race
to cause visible issues in general.

Fix the race by clearing the TXEMPTY bit in ISR *before* filling the
FIFO.

The TXEMPTY bit in ISR will only get asserted at the exact moment the
TX FIFO *becomes* empty, so clearing the bit before filling FIFO does
not cause an extra immediate assertion even if the FIFO is initially
empty.

This is hard to reproduce directly on a normal system, but inserting
e.g. udelay(200) after cdns_uart_handle_tx(port), setting 4000000 baud,
and then running "dd if=/dev/zero bs=128 of=/dev/ttyPS0 count=50"
reliably reproduces the issue on my ZynqMP test system unless this fix
is applied.

Fixes: 85baf542d54e ("tty: xuartps: support 64 byte FIFO size")
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Link: https://lore.kernel.org/r/20211026102741.2910441-1-anssi.hannula@bitwise.fi
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
serial: 8250_dw: Drop wrong use of ACPI_PTR() 2021-11-17T08:48:42+00:00 Andy Shevchenko andriy.shevchenko@linux.intel.com 2021-10-05T13:45:16+00:00 15355466cdedcbf60efa301f2fc89277b1318990 [ Upstream commit ebabb77a2a115b6c5e68f7364b598310b5f61fb2 ] ACPI_PTR() is more harmful than helpful. For example, in this case if CONFIG_ACPI=n, the ID table left unused which is not what we want. Instead of adding ifdeffery here and there, drop ACPI_PTR(). Fixes: 6a7320c4669f ("serial: 8250_dw: Add ACPI 5.0 support") Reported-by: Daniel Palmer <daniel@0x0f.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20211005134516.23218-1-andriy.shevchenko@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit ebabb77a2a115b6c5e68f7364b598310b5f61fb2 ]

ACPI_PTR() is more harmful than helpful. For example, in this case
if CONFIG_ACPI=n, the ID table left unused which is not what we want.

Instead of adding ifdeffery here and there, drop ACPI_PTR().

Fixes: 6a7320c4669f ("serial: 8250_dw: Add ACPI 5.0 support")
Reported-by: Daniel Palmer <daniel@0x0f.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20211005134516.23218-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
serial: core: Fix initializing and restoring termios speed 2021-11-17T08:48:25+00:00 Pali Rohár pali@kernel.org 2021-10-02T13:09:00+00:00 e9adf72bdbd576a9d171ad933c7c2d7139a2444b commit 027b57170bf8bb6999a28e4a5f3d78bf1db0f90c upstream. Since commit edc6afc54968 ("tty: switch to ktermios and new framework") termios speed is no longer stored only in c_cflag member but also in new additional c_ispeed and c_ospeed members. If BOTHER flag is set in c_cflag then termios speed is stored only in these new members. Therefore to correctly restore termios speed it is required to store also ispeed and ospeed members, not only cflag member. In case only cflag member with BOTHER flag is restored then functions tty_termios_baud_rate() and tty_termios_input_baud_rate() returns baudrate stored in c_ospeed / c_ispeed member, which is zero as it was not restored too. If reported baudrate is invalid (e.g. zero) then serial core functions report fallback baudrate value 9600. So it means that in this case original baudrate is lost and kernel changes it to value 9600. Simple reproducer of this issue is to boot kernel with following command line argument: "console=ttyXXX,86400" (where ttyXXX is the device name). For speed 86400 there is no Bnnn constant and therefore kernel has to represent this speed via BOTHER c_cflag. Which means that speed is stored only in c_ospeed and c_ispeed members, not in c_cflag anymore. If bootloader correctly configures serial device to speed 86400 then kernel prints boot log to early console at speed speed 86400 without any issue. But after kernel starts initializing real console device ttyXXX then speed is changed to fallback value 9600 because information about speed was lost. This patch fixes above issue by storing and restoring also ispeed and ospeed members, which are required for BOTHER flag. Fixes: edc6afc54968 ("[PATCH] tty: switch to ktermios and new framework") Cc: stable@vger.kernel.org Signed-off-by: Pali Rohár <pali@kernel.org> Link: https://lore.kernel.org/r/20211002130900.9518-1-pali@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 027b57170bf8bb6999a28e4a5f3d78bf1db0f90c upstream.

Since commit edc6afc54968 ("tty: switch to ktermios and new framework")
termios speed is no longer stored only in c_cflag member but also in new
additional c_ispeed and c_ospeed members. If BOTHER flag is set in c_cflag
then termios speed is stored only in these new members.

Therefore to correctly restore termios speed it is required to store also
ispeed and ospeed members, not only cflag member.

In case only cflag member with BOTHER flag is restored then functions
tty_termios_baud_rate() and tty_termios_input_baud_rate() returns baudrate
stored in c_ospeed / c_ispeed member, which is zero as it was not restored
too. If reported baudrate is invalid (e.g. zero) then serial core functions
report fallback baudrate value 9600. So it means that in this case original
baudrate is lost and kernel changes it to value 9600.

Simple reproducer of this issue is to boot kernel with following command
line argument: "console=ttyXXX,86400" (where ttyXXX is the device name).
For speed 86400 there is no Bnnn constant and therefore kernel has to
represent this speed via BOTHER c_cflag. Which means that speed is stored
only in c_ospeed and c_ispeed members, not in c_cflag anymore.

If bootloader correctly configures serial device to speed 86400 then kernel
prints boot log to early console at speed speed 86400 without any issue.
But after kernel starts initializing real console device ttyXXX then speed
is changed to fallback value 9600 because information about speed was lost.

This patch fixes above issue by storing and restoring also ispeed and
ospeed members, which are required for BOTHER flag.

Fixes: edc6afc54968 ("[PATCH] tty: switch to ktermios and new framework")
Cc: stable@vger.kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20211002130900.9518-1-pali@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tty: Fix out-of-bound vmalloc access in imageblit 2021-10-06T13:42:29+00:00 Igor Matheus Andrade Torrente igormtorrente@gmail.com 2021-06-28T13:45:09+00:00 883f7897a25e3ce14a7f274ca4c73f49ac84002a [ Upstream commit 3b0c406124719b625b1aba431659f5cdc24a982c ] This issue happens when a userspace program does an ioctl FBIOPUT_VSCREENINFO passing the fb_var_screeninfo struct containing only the fields xres, yres, and bits_per_pixel with values. If this struct is the same as the previous ioctl, the vc_resize() detects it and doesn't call the resize_screen(), leaving the fb_var_screeninfo incomplete. And this leads to the updatescrollmode() calculates a wrong value to fbcon_display->vrows, which makes the real_y() return a wrong value of y, and that value, eventually, causes the imageblit to access an out-of-bound address value. To solve this issue I made the resize_screen() be called even if the screen does not need any resizing, so it will "fix and fill" the fb_var_screeninfo independently. Cc: stable <stable@vger.kernel.org> # after 5.15-rc2 is out, give it time to bake Reported-and-tested-by: syzbot+858dc7a2f7ef07c2c219@syzkaller.appspotmail.com Signed-off-by: Igor Matheus Andrade Torrente <igormtorrente@gmail.com> Link: https://lore.kernel.org/r/20210628134509.15895-1-igormtorrente@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit 3b0c406124719b625b1aba431659f5cdc24a982c ]

This issue happens when a userspace program does an ioctl
FBIOPUT_VSCREENINFO passing the fb_var_screeninfo struct
containing only the fields xres, yres, and bits_per_pixel
with values.

If this struct is the same as the previous ioctl, the
vc_resize() detects it and doesn't call the resize_screen(),
leaving the fb_var_screeninfo incomplete. And this leads to
the updatescrollmode() calculates a wrong value to
fbcon_display->vrows, which makes the real_y() return a
wrong value of y, and that value, eventually, causes
the imageblit to access an out-of-bound address value.

To solve this issue I made the resize_screen() be called
even if the screen does not need any resizing, so it will
"fix and fill" the fb_var_screeninfo independently.

Cc: stable <stable@vger.kernel.org> # after 5.15-rc2 is out, give it time to bake
Reported-and-tested-by: syzbot+858dc7a2f7ef07c2c219@syzkaller.appspotmail.com
Signed-off-by: Igor Matheus Andrade Torrente <igormtorrente@gmail.com>
Link: https://lore.kernel.org/r/20210628134509.15895-1-igormtorrente@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
tty: synclink_gt: rename a conflicting function name 2021-09-30T08:09:23+00:00 Randy Dunlap rdunlap@infradead.org 2021-09-02T00:38:06+00:00 5bcead7cde68cc58212018e376b1cef2ab2d2ee2 [ Upstream commit 06e49073dfba24df4b1073a068631b13a0039c34 ] 'set_signals()' in synclink_gt.c conflicts with an exported symbol in arch/um/, so change set_signals() to set_gtsignals(). Keep the function names similar by also changing get_signals() to get_gtsignals(). ../drivers/tty/synclink_gt.c:442:13: error: conflicting types for ‘set_signals’ static void set_signals(struct slgt_info *info); ^~~~~~~~~~~ In file included from ../include/linux/irqflags.h:16:0, from ../include/linux/spinlock.h:58, from ../include/linux/mm_types.h:9, from ../include/linux/buildid.h:5, from ../include/linux/module.h:14, from ../drivers/tty/synclink_gt.c:46: ../arch/um/include/asm/irqflags.h:6:5: note: previous declaration of ‘set_signals’ was here int set_signals(int enable); ^~~~~~~~~~~ Fixes: 705b6c7b34f2 ("[PATCH] new driver synclink_gt") Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jirislaby@kernel.org> Cc: Paul Fulghum <paulkf@microgate.com> Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Link: https://lore.kernel.org/r/20210902003806.17054-1-rdunlap@infradead.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit 06e49073dfba24df4b1073a068631b13a0039c34 ]

'set_signals()' in synclink_gt.c conflicts with an exported symbol
in arch/um/, so change set_signals() to set_gtsignals(). Keep
the function names similar by also changing get_signals() to
get_gtsignals().

../drivers/tty/synclink_gt.c:442:13: error: conflicting types for ‘set_signals’
 static void set_signals(struct slgt_info *info);
             ^~~~~~~~~~~
In file included from ../include/linux/irqflags.h:16:0,
                 from ../include/linux/spinlock.h:58,
                 from ../include/linux/mm_types.h:9,
                 from ../include/linux/buildid.h:5,
                 from ../include/linux/module.h:14,
                 from ../drivers/tty/synclink_gt.c:46:
../arch/um/include/asm/irqflags.h:6:5: note: previous declaration of ‘set_signals’ was here
 int set_signals(int enable);
     ^~~~~~~~~~~

Fixes: 705b6c7b34f2 ("[PATCH] new driver synclink_gt")
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: Paul Fulghum <paulkf@microgate.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/r/20210902003806.17054-1-rdunlap@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
tty: synclink_gt, drop unneeded forward declarations 2021-09-30T08:09:23+00:00 Jiri Slaby jslaby@suse.cz 2021-03-02T06:22:09+00:00 c5f27aedf6bbe232237aeb6e6c37b8461544f04d [ Upstream commit b9b90fe655c0bd816847ac1bcbf179cfa2981ecb ] Forward declarations make the code larger and rewrites harder. Harder as they are often omitted from global changes. Remove forward declarations which are not really needed, i.e. the definition of the function is before its first use. Signed-off-by: Jiri Slaby <jslaby@suse.cz> Link: https://lore.kernel.org/r/20210302062214.29627-39-jslaby@suse.cz Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit b9b90fe655c0bd816847ac1bcbf179cfa2981ecb ]

Forward declarations make the code larger and rewrites harder. Harder as
they are often omitted from global changes. Remove forward declarations
which are not really needed, i.e. the definition of the function is
before its first use.

Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210302062214.29627-39-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
serial: mvebu-uart: fix driver's tx_empty callback 2021-09-30T08:09:22+00:00 Pali Rohár pali@kernel.org 2021-09-11T13:20:17+00:00 494260e20ac25cc281671ce3cf05b2bd1c66f8a3 commit 74e1eb3b4a1ef2e564b4bdeb6e92afe844e900de upstream. Driver's tx_empty callback should signal when the transmit shift register is empty. So when the last character has been sent. STAT_TX_FIFO_EMP bit signals only that HW transmit FIFO is empty, which happens when the last byte is loaded into transmit shift register. STAT_TX_EMP bit signals when the both HW transmit FIFO and transmit shift register are empty. So replace STAT_TX_FIFO_EMP check by STAT_TX_EMP in mvebu_uart_tx_empty() callback function. Fixes: 30530791a7a0 ("serial: mvebu-uart: initial support for Armada-3700 serial port") Cc: stable <stable@vger.kernel.org> Signed-off-by: Pali Rohár <pali@kernel.org> Link: https://lore.kernel.org/r/20210911132017.25505-1-pali@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 74e1eb3b4a1ef2e564b4bdeb6e92afe844e900de upstream.

Driver's tx_empty callback should signal when the transmit shift register
is empty. So when the last character has been sent.

STAT_TX_FIFO_EMP bit signals only that HW transmit FIFO is empty, which
happens when the last byte is loaded into transmit shift register.

STAT_TX_EMP bit signals when the both HW transmit FIFO and transmit shift
register are empty.

So replace STAT_TX_FIFO_EMP check by STAT_TX_EMP in mvebu_uart_tx_empty()
callback function.

Fixes: 30530791a7a0 ("serial: mvebu-uart: initial support for Armada-3700 serial port")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20210911132017.25505-1-pali@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
console: consume APC, DM, DCS 2021-09-26T12:07:05+00:00 nick black dankamongmen@gmail.com 2021-08-30T08:56:15+00:00 bd292c687390859d85cdedcf53c93f5e49c1f814 commit 3a2b2eb55681158d3e3ef464fbf47574cf0c517c upstream. The Linux console's VT102 implementation already consumes OSC ("Operating System Command") sequences, probably because that's how palette changes are transmitted. In addition to OSC, there are three other major clases of ANSI control strings: APC ("Application Program Command"), PM ("Privacy Message"), and DCS ("Device Control String"). They are handled similarly to OSC in terms of termination. Source: vt100.net Add three new enumerated states, one for each of these types. All three are handled the same way right now--they simply consume input until terminated. I hope to expand upon this firmament in the future. Add new predicate ansi_control_string(), returning true for any of these states. Replace explicit checks against ESosc with calls to this function. Transition to these states appropriately from the escape initiation (ESesc) state. This was motivated by the following Notcurses bugs: https://github.com/dankamongmen/notcurses/issues/2050 https://github.com/dankamongmen/notcurses/issues/1828 https://github.com/dankamongmen/notcurses/issues/2069 where standard VT sequences are not consumed by the Linux console. It's not necessary that the Linux console *support* these sequences, but it ought *consume* these well-specified classes of sequences. Tested by sending a variety of escape sequences to the console, and verifying that they still worked, or were now properly consumed. Verified that the escapes were properly terminated at a generic level. Verified that the Notcurses tools continued to show expected output on the Linux console, except now without escape bleedthrough. Link: https://lore.kernel.org/lkml/YSydL0q8iaUfkphg@schwarzgerat.orthanc/ Signed-off-by: nick black <dankamongmen@gmail.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jirislaby@kernel.org> Cc: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 3a2b2eb55681158d3e3ef464fbf47574cf0c517c upstream.

The Linux console's VT102 implementation already consumes OSC
("Operating System Command") sequences, probably because that's how
palette changes are transmitted.

In addition to OSC, there are three other major clases of ANSI control
strings: APC ("Application Program Command"), PM ("Privacy Message"),
and DCS ("Device Control String").  They are handled similarly to OSC in
terms of termination.

Source: vt100.net

Add three new enumerated states, one for each of these types.  All three
are handled the same way right now--they simply consume input until
terminated.  I hope to expand upon this firmament in the future.  Add
new predicate ansi_control_string(), returning true for any of these
states.  Replace explicit checks against ESosc with calls to this
function.  Transition to these states appropriately from the escape
initiation (ESesc) state.

This was motivated by the following Notcurses bugs:

 https://github.com/dankamongmen/notcurses/issues/2050
 https://github.com/dankamongmen/notcurses/issues/1828
 https://github.com/dankamongmen/notcurses/issues/2069

where standard VT sequences are not consumed by the Linux console.  It's
not necessary that the Linux console *support* these sequences, but it
ought *consume* these well-specified classes of sequences.

Tested by sending a variety of escape sequences to the console, and
verifying that they still worked, or were now properly consumed.
Verified that the escapes were properly terminated at a generic level.
Verified that the Notcurses tools continued to show expected output on
the Linux console, except now without escape bleedthrough.

Link: https://lore.kernel.org/lkml/YSydL0q8iaUfkphg@schwarzgerat.orthanc/
Signed-off-by: nick black <dankamongmen@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
serial: sh-sci: fix break handling for sysrq 2021-09-22T10:26:33+00:00 Ulrich Hecht uli+renesas@fpond.eu 2021-08-16T16:22:01+00:00 2918eca4970a1434cb3890f8ddfd39758823c97a [ Upstream commit 87b8061bad9bd4b549b2daf36ffbaa57be2789a2 ] This fixes two issues that cause the sysrq sequence to be inadvertently aborted on SCIF serial consoles: - a NUL character remains in the RX queue after a break has been detected, which is then passed on to uart_handle_sysrq_char() - the break interrupt is handled twice on controllers with multiplexed ERI and BRI interrupts Signed-off-by: Ulrich Hecht <uli+renesas@fpond.eu> Link: https://lore.kernel.org/r/20210816162201.28801-1-uli+renesas@fpond.eu Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit 87b8061bad9bd4b549b2daf36ffbaa57be2789a2 ]

This fixes two issues that cause the sysrq sequence to be inadvertently
aborted on SCIF serial consoles:

- a NUL character remains in the RX queue after a break has been detected,
  which is then passed on to uart_handle_sysrq_char()
- the break interrupt is handled twice on controllers with multiplexed ERI
  and BRI interrupts

Signed-off-by: Ulrich Hecht <uli+renesas@fpond.eu>
Link: https://lore.kernel.org/r/20210816162201.28801-1-uli+renesas@fpond.eu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
serial: 8250_pci: make setup_port() parameters explicitly unsigned 2021-09-22T10:26:30+00:00 Greg Kroah-Hartman gregkh@linuxfoundation.org 2021-07-26T13:07:17+00:00 44fd61a8bd0dc543a1bdde557f0cb4487ac44ffd [ Upstream commit 3a96e97ab4e835078e6f27b7e1c0947814df3841 ] The bar and offset parameters to setup_port() are used in pointer math, and while it would be very difficult to get them to wrap as a negative number, just be "safe" and make them unsigned so that static checkers do not trip over them unintentionally. Cc: Jiri Slaby <jirislaby@kernel.org> Reported-by: Jordy Zomer <jordy@pwning.systems> Link: https://lore.kernel.org/r/20210726130717.2052096-1-gregkh@linuxfoundation.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit 3a96e97ab4e835078e6f27b7e1c0947814df3841 ]

The bar and offset parameters to setup_port() are used in pointer math,
and while it would be very difficult to get them to wrap as a negative
number, just be "safe" and make them unsigned so that static checkers do
not trip over them unintentionally.

Cc: Jiri Slaby <jirislaby@kernel.org>
Reported-by: Jordy Zomer <jordy@pwning.systems>
Link: https://lore.kernel.org/r/20210726130717.2052096-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>