linux-stable.git/drivers/tty, branch v5.19.2

tty: serial: qcom-geni-serial: Fix %lu -> %u in print statements

2022-08-17T13:16:01+00:00

[ Upstream commit 0fec518018cc5ceffa706370b6e3acbbb1e3c798 ]

When we multiply an unsigned int by a u32 we still end up with an
unsigned int. That means we should specify "%u" not "%lu" in the
format code.

NOTE: this fix was chosen instead of somehow promoting the value to
"unsigned long" since the max baud rate from the earlier call to
uart_get_baud_rate() is 4000000 and the max sampling rate is 32.
4000000 * 32 = 0x07a12000, not even close to overflowing 32-bits.

Fixes: c474c775716e ("tty: serial: qcom-geni-serial: Fix get_clk_div_rate() which otherwise could return a sub-optimal clock rate.")
Reported-by: Mark Brown 
Signed-off-by: Douglas Anderson 
Link: https://lore.kernel.org/r/20220802132250.1.Iea061e14157a17e114dbe2eca764568a02d6b889@changeid
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Sasha Levin

tty: serial: fsl_lpuart: correct the count of break characters

2022-08-17T13:15:59+00:00

[ Upstream commit 707f816f25590c20e056b3bd4a17ce69b03fe856 ]

The LPUART can't distinguish between a break signal and a framing error,
so need to count the break characters if there is a framing error and
received data is zero instead of the parity error.

Fixes: 5541a9bacfe5 ("serial: fsl_lpuart: handle break and make sysrq work")
Reviewed-by: Michael Walle 
Signed-off-by: Sherry Sun 
Link: https://lore.kernel.org/r/20220725050115.12396-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Sasha Levin

tty: serial: qcom-geni-serial: Fix get_clk_div_rate() which otherwise could return a sub-optimal clock rate.

2022-08-17T13:15:59+00:00

[ Upstream commit c474c775716edd46a51bf8161142bbd1545f8733 ]

In the logic around call to clk_round_rate(), for some corner conditions,
get_clk_div_rate() could return an sub-optimal clock rate. Also, if an
exact clock rate was not found lowest clock was being returned.

Search for suitable clock rate in 2 steps
a) exact match or within 2% tolerance
b) within 5% tolerance
This also takes care of corner conditions.

Fixes: c2194bc999d4 ("tty: serial: qcom-geni-serial: Remove uart frequency table. Instead, find suitable frequency with call to clk_round_rate")
Reviewed-by: Douglas Anderson 
Signed-off-by: Vijaya Krishna Nivarthi 
Link: https://lore.kernel.org/r/1657911343-1909-1-git-send-email-quic_vnivarth@quicinc.com
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Sasha Levin

serial: 8250_bcm2835aux: Add missing clk_disable_unprepare()

2022-08-17T13:15:59+00:00

[ Upstream commit b9f1736e475dba0d6da48fdcb831248ab1597886 ]

The error path when get clock frequency fails in bcm2835aux_serial
driver does not correctly disable the clock.

This flaw was found using a static analysis tool "Hulk Robot", which
reported the following warning when analyzing linux-next/master:

    drivers/tty/serial/8250/8250_bcm2835aux.c:
    warning: clk_disable_unprepare_missing.cocci

The cocci script checks for the existence of clk_disable_unprepare()
paired with clk_prepare_enable().

Add the missing clk_disable_unprepare() to the error path.

Fixes: fcc446c8aa63 ("serial: 8250_bcm2835aux: Add ACPI support")
Reported-by: Hulk Robot 
Reviewed-by: Florian Fainelli 
Signed-off-by: Guo Mengqi 
Link: https://lore.kernel.org/r/20220715023312.37808-1-guomengqi3@huawei.com
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Sasha Levin

serial: 8250_bcm7271: Save/restore RTS in suspend/resume

2022-08-17T13:15:53+00:00

[ Upstream commit 3182efd036c1b955403d131258234896cbd9fbeb ]

Commit 9cabe26e65a8 ("serial: 8250_bcm7271: UART errors after resuming
from S2") prevented an early enabling of RTS during resume, but it did
not actively restore the RTS state after resume.

Fixes: 9cabe26e65a8 ("serial: 8250_bcm7271: UART errors after resuming from S2")
Signed-off-by: Doug Berger 
Signed-off-by: Florian Fainelli 
Link: https://lore.kernel.org/r/20220714031316.404918-1-f.fainelli@gmail.com
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Sasha Levin

tty: n_gsm: fix missing corner cases in gsmld_poll()

2022-08-17T13:15:51+00:00

[ Upstream commit 7e5b4322cde067e1d0f1bf8f490e93f664a7c843 ]

gsmld_poll() currently fails to handle the following corner cases correctly:
- remote party closed the associated tty

Add the missing checks and map those to EPOLLHUP.
Reorder the checks to group them by their reaction.

Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Signed-off-by: Daniel Starke 
Link: https://lore.kernel.org/r/20220707113223.3685-4-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Sasha Levin

tty: n_gsm: fix flow control handling in tx path

2022-08-17T13:15:51+00:00

[ Upstream commit 59ff0680ecbfec742b1e0381e7cc46b41eb06647 ]

The current implementation constipates all transmission paths during flow
control except for flow control frames. However, these may not be located
at the beginning of the transmission queue of the control channel.
Ensure that flow control frames in the transmission queue for the control
channel are always handled even if constipated by skipping through other
messages.

Fixes: 0af021678d5d ("tty: n_gsm: fix deadlock and link starvation in outgoing data path")
Signed-off-by: Daniel Starke 
Link: https://lore.kernel.org/r/20220707113223.3685-3-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Sasha Levin

tty: n_gsm: fix DM command

2022-08-17T13:15:51+00:00

[ Upstream commit 18a948c7d90995d127785e308fa7b701df4c499f ]

n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.3.3 defines the DM response. There exists
no DM command. However, the current implementation incorrectly sends DM as
command in case of unexpected UIH frames in gsm_queue().
Correct this behavior by always sending DM as response.

Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Signed-off-by: Daniel Starke 
Link: https://lore.kernel.org/r/20220707113223.3685-2-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Sasha Levin

tty: n_gsm: fix wrong T1 retry count handling

2022-08-17T13:15:51+00:00

[ Upstream commit f30e10caa80aa1f35508bc17fc302dbbde9a833c ]

n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.7.3 states that the valid range for the
maximum number of retransmissions (N2) is from 0 to 255 (both including).
gsm_dlci_t1() handles this number incorrectly by performing N2 - 1
retransmission attempts. Setting N2 to zero results in more than 255
retransmission attempts.
Fix gsm_dlci_t1() to comply with 3GPP 27.010.

Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Signed-off-by: Daniel Starke 
Link: https://lore.kernel.org/r/20220707113223.3685-1-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Sasha Levin

serial: 8250_fsl: Don't report FE, PE and OE twice

2022-08-17T13:15:51+00:00

[ Upstream commit 9d3aaceb73acadf134596a2f8db9c451c1332d3d ]

Some Freescale 8250 implementations have the problem that a single long
break results in one irq per character frame time. The code in
fsl8250_handle_irq() that is supposed to handle that uses the BI bit in
lsr_saved_flags to detect such a situation and then skip the second
received character. However it also stores other error bits and so after
a single frame error the character received in the next irq handling is
passed to the upper layer with a frame error, too.

So after a spike on the data line (which is correctly recognized as a
frame error) the following valid character is thrown away, because the
driver reports a frame error for that one, too.

To weaken this problem restrict saving LSR to only the BI bit.

Note however that the handling is still broken:

 - lsr_saved_flags is updated using orig_lsr which is the LSR content
   for the first received char, but there might be more in the FIFO, so
   a character is thrown away that is received later and not necessarily
   the one following the break.
 - The doubled break might be the 2nd and 3rd char in the FIFO, so the
   workaround doesn't catch these, because serial8250_rx_chars() doesn't
   handle the workaround.
 - lsr_saved_flags might have set UART_LSR_BI at the entry of
   fsl8250_handle_irq() which doesn't originate from
   fsl8250_handle_irq()'s "up->lsr_saved_flags |= orig_lsr &
   UART_LSR_BI;" but from e.g. from serial8250_tx_empty().
 - For a long or a short break this isn't about two characters, but more
   or only a single one.

Fixes: 9deaa53ac7fa ("serial: add irq handler for Freescale 16550 errata.")
Acked-by: Ilpo Järvinen 
Signed-off-by: Uwe Kleine-König 
Link: https://lore.kernel.org/r/20220704085119.55900-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Sasha Levin