linux-stable.git/drivers/tty, branch v3.18.25

serial: 8250_pci: Add support for 12 port Exar boards

2015-11-15T17:51:53+00:00

[ Upstream commit be32c0cf0462c36f482b5ddcff1d8371be1e183c ]

The Exar XR17V358 can also be combined with a XR17V354 chip to act as a
single 12 port chip. This works the same way as the combining two XR17V358
chips. But the reported device id then is 0x4358.

Signed-off-by: Soeren Grunewald 
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Sasha Levin

serial: 8250_pci: Add support for 16 port Exar boards

2015-11-15T17:51:53+00:00

[ Upstream commit 96a5d18bc1338786fecac73599f1681f59a59a8e ]

The Exar XR17V358 chip usually provides only 8 ports. But two chips can be
combined to act as a single 16 port chip. Therefor one chip is configured
as master the second as slave by connecting the mode pin to VCC (master)
or GND (slave).

Then the master chip is reporting a different device-id depending on
whether a slave is detected or not. The UARTs 8-15 are addressed from
0x2000-0x3fff. So the offset of 0x400 from UART to UART can be used to
address all 16 ports as before.

See: https://www.exar.com/common/content/document.ashx?id=1587 page 11

Signed-off-by: Soeren Grunewald 
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Sasha Levin

tty: fix stall caused by missing memory barrier in drivers/tty/n_tty.c

2015-10-31T13:00:00+00:00

[ Upstream commit e81107d4c6bd098878af9796b24edc8d4a9524fd ]

My colleague ran into a program stall on a x86_64 server, where
n_tty_read() was waiting for data even if there was data in the buffer
in the pty.  kernel stack for the stuck process looks like below.
 #0 [ffff88303d107b58] __schedule at ffffffff815c4b20
 #1 [ffff88303d107bd0] schedule at ffffffff815c513e
 #2 [ffff88303d107bf0] schedule_timeout at ffffffff815c7818
 #3 [ffff88303d107ca0] wait_woken at ffffffff81096bd2
 #4 [ffff88303d107ce0] n_tty_read at ffffffff8136fa23
 #5 [ffff88303d107dd0] tty_read at ffffffff81368013
 #6 [ffff88303d107e20] __vfs_read at ffffffff811a3704
 #7 [ffff88303d107ec0] vfs_read at ffffffff811a3a57
 #8 [ffff88303d107f00] sys_read at ffffffff811a4306
 #9 [ffff88303d107f50] entry_SYSCALL_64_fastpath at ffffffff815c86d7

There seems to be two problems causing this issue.

First, in drivers/tty/n_tty.c, __receive_buf() stores the data and
updates ldata->commit_head using smp_store_release() and then checks
the wait queue using waitqueue_active().  However, since there is no
memory barrier, __receive_buf() could return without calling
wake_up_interactive_poll(), and at the same time, n_tty_read() could
start to wait in wait_woken() as in the following chart.

        __receive_buf()                         n_tty_read()
------------------------------------------------------------------------
if (waitqueue_active(&tty->read_wait))
/* Memory operations issued after the
   RELEASE may be completed before the
   RELEASE operation has completed */
                                        add_wait_queue(&tty->read_wait, &wait);
                                        ...
                                        if (!input_available_p(tty, 0)) {
smp_store_release(&ldata->commit_head,
                  ldata->read_head);
                                        ...
                                        timeout = wait_woken(&wait,
                                          TASK_INTERRUPTIBLE, timeout);
------------------------------------------------------------------------

The second problem is that n_tty_read() also lacks a memory barrier
call and could also cause __receive_buf() to return without calling
wake_up_interactive_poll(), and n_tty_read() to wait in wait_woken()
as in the chart below.

        __receive_buf()                         n_tty_read()
------------------------------------------------------------------------
                                        spin_lock_irqsave(&q->lock, flags);
                                        /* from add_wait_queue() */
                                        ...
                                        if (!input_available_p(tty, 0)) {
                                        /* Memory operations issued after the
                                           RELEASE may be completed before the
                                           RELEASE operation has completed */
smp_store_release(&ldata->commit_head,
                  ldata->read_head);
if (waitqueue_active(&tty->read_wait))
                                        __add_wait_queue(q, wait);
                                        spin_unlock_irqrestore(&q->lock,flags);
                                        /* from add_wait_queue() */
                                        ...
                                        timeout = wait_woken(&wait,
                                          TASK_INTERRUPTIBLE, timeout);
------------------------------------------------------------------------

There are also other places in drivers/tty/n_tty.c which have similar
calls to waitqueue_active(), so instead of adding many memory barrier
calls, this patch simply removes the call to waitqueue_active(),
leaving just wake_up*() behind.

This fixes both problems because, even though the memory access before
or after the spinlocks in both wake_up*() and add_wait_queue() can
sneak into the critical section, it cannot go past it and the critical
section assures that they will be serialized (please see "INTER-CPU
ACQUIRING BARRIER EFFECTS" in Documentation/memory-barriers.txt for a
better explanation).  Moreover, the resulting code is much simpler.

Latency measurement using a ping-pong test over a pty doesn't show any
visible performance drop.

Signed-off-by: Kosuke Tatsukawa 
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Sasha Levin

Revert "tty: fix stall caused by missing memory barrier in drivers/tty/n_tty.c"

2015-10-31T12:54:32+00:00

This reverts commit af32cc7bde6304dac92e6a74fe4b2cc8120cb29a.

The commit was incorrectly backported and was causing hangs.

Reported-by: Corey Wright 
Signed-off-by: Sasha Levin

serial: 8250: don't bind to SMSC IrCC IR port

2015-10-28T02:14:43+00:00

[ Upstream commit ffa34de03bcfbfa88d8352942bc238bb48e94e2d ]

SMSC IrCC SIR/FIR port should not be bound to by
(legacy) serial driver so its own driver (smsc-ircc2)
can bind to it.

Signed-off-by: Maciej Szmigiero 
Cc: stable 
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Sasha Levin

tty: fix stall caused by missing memory barrier in drivers/tty/n_tty.c

2015-10-28T02:14:29+00:00

[ Upstream commit e81107d4c6bd098878af9796b24edc8d4a9524fd ]

My colleague ran into a program stall on a x86_64 server, where
n_tty_read() was waiting for data even if there was data in the buffer
in the pty.  kernel stack for the stuck process looks like below.
 #0 [ffff88303d107b58] __schedule at ffffffff815c4b20
 #1 [ffff88303d107bd0] schedule at ffffffff815c513e
 #2 [ffff88303d107bf0] schedule_timeout at ffffffff815c7818
 #3 [ffff88303d107ca0] wait_woken at ffffffff81096bd2
 #4 [ffff88303d107ce0] n_tty_read at ffffffff8136fa23
 #5 [ffff88303d107dd0] tty_read at ffffffff81368013
 #6 [ffff88303d107e20] __vfs_read at ffffffff811a3704
 #7 [ffff88303d107ec0] vfs_read at ffffffff811a3a57
 #8 [ffff88303d107f00] sys_read at ffffffff811a4306
 #9 [ffff88303d107f50] entry_SYSCALL_64_fastpath at ffffffff815c86d7

There seems to be two problems causing this issue.

First, in drivers/tty/n_tty.c, __receive_buf() stores the data and
updates ldata->commit_head using smp_store_release() and then checks
the wait queue using waitqueue_active().  However, since there is no
memory barrier, __receive_buf() could return without calling
wake_up_interactive_poll(), and at the same time, n_tty_read() could
start to wait in wait_woken() as in the following chart.

        __receive_buf()                         n_tty_read()
------------------------------------------------------------------------
if (waitqueue_active(&tty->read_wait))
/* Memory operations issued after the
   RELEASE may be completed before the
   RELEASE operation has completed */
                                        add_wait_queue(&tty->read_wait, &wait);
                                        ...
                                        if (!input_available_p(tty, 0)) {
smp_store_release(&ldata->commit_head,
                  ldata->read_head);
                                        ...
                                        timeout = wait_woken(&wait,
                                          TASK_INTERRUPTIBLE, timeout);
------------------------------------------------------------------------

The second problem is that n_tty_read() also lacks a memory barrier
call and could also cause __receive_buf() to return without calling
wake_up_interactive_poll(), and n_tty_read() to wait in wait_woken()
as in the chart below.

        __receive_buf()                         n_tty_read()
------------------------------------------------------------------------
                                        spin_lock_irqsave(&q->lock, flags);
                                        /* from add_wait_queue() */
                                        ...
                                        if (!input_available_p(tty, 0)) {
                                        /* Memory operations issued after the
                                           RELEASE may be completed before the
                                           RELEASE operation has completed */
smp_store_release(&ldata->commit_head,
                  ldata->read_head);
if (waitqueue_active(&tty->read_wait))
                                        __add_wait_queue(q, wait);
                                        spin_unlock_irqrestore(&q->lock,flags);
                                        /* from add_wait_queue() */
                                        ...
                                        timeout = wait_woken(&wait,
                                          TASK_INTERRUPTIBLE, timeout);
------------------------------------------------------------------------

There are also other places in drivers/tty/n_tty.c which have similar
calls to waitqueue_active(), so instead of adding many memory barrier
calls, this patch simply removes the call to waitqueue_active(),
leaving just wake_up*() behind.

This fixes both problems because, even though the memory access before
or after the spinlocks in both wake_up*() and add_wait_queue() can
sneak into the critical section, it cannot go past it and the critical
section assures that they will be serialized (please see "INTER-CPU
ACQUIRING BARRIER EFFECTS" in Documentation/memory-barriers.txt for a
better explanation).  Moreover, the resulting code is much simpler.

Latency measurement using a ping-pong test over a pty doesn't show any
visible performance drop.

Signed-off-by: Kosuke Tatsukawa 
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Sasha Levin

tty/serial: at91: RS485 mode: 0 is valid for delay_rts_after_send

2015-07-12T14:54:24+00:00

[ Upstream commit 8687634b7908c42eb700e0469e110e02833611d1 ]

In RS485 mode, we may want to set the delay_rts_after_send value to 0.
In the datasheet, the 0 value is said to "disable" the Transmitter Timeguard but
this is exactly the expected behavior if we want no delay...

Moreover, if the value was set to non-zero value by device-tree or earlier
ioctl command, it was impossible to change it back to zero.

Reported-by: Sami Pietikäinen 
Signed-off-by: Nicolas Ferre 
Cc: stable@vger.kernel.org  # 3.2+
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Sasha Levin

serial: imx: Fix DMA handling for IDLE condition aborts

2015-07-03T16:34:44+00:00

[ Upstream commit 392bceedb107a3dc1d4287e63d7670d08f702feb ]

The driver configures the IDLE condition to interrupt the SDMA engine.
Since the SDMA UART ROM script doesn't clear the IDLE bit itself, this
caused repeated 1-byte DMA transfers, regardless of available data in the
RX FIFO. Also, when returning due to the IDLE condition, the UART ROM
script already increased its counter, causing residue to be off by one.

This patch clears the IDLE condition to avoid repeated 1-byte DMA transfers
and decreases count by when the DMA transfer was aborted due to the IDLE
condition, fixing serial transfers using DMA on i.MX6Q.

Reported-by: Peter Seiderer 
Signed-off-by: Philipp Zabel 
Tested-by: Fabio Estevam 
Cc: stable 
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Sasha Levin

n_tty: Fix auditing support for cannonical mode

2015-07-03T16:34:34+00:00

[ Upstream commit 72586c6061ab8c23ffd9f301ed19782a44ff5f04 ]

Commit 32f13521ca68bc624ff6effc77f308a52b038bf0
("n_tty: Line copy to user buffer in canonical mode")
changed cannonical mode copying to use copy_to_user
but missed adding the call to the audit framework.
Add in the appropriate functions to get audit support.

Fixes: 32f13521ca68 ("n_tty: Line copy to user buffer in canonical mode")
Reported-by: Miloslav Trmač 
Signed-off-by: Laura Abbott 
Reviewed-by: Peter Hurley 
Cc: stable 
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Sasha Levin

serial: 8250_dw: add support for AMD SOC Carrizo

2015-06-28T17:39:20+00:00

[ Upstream commit 5ef86b74209db33c133b5f18738dd8f3189b63a1 ]

Add ACPI identifier for UART on AMD SOC Carrizo.

Signed-off-by: Ken Xue 
Cc: stable 
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Sasha Levin