linux-stable.git/drivers/tty, branch linux-4.19.y

serial: 8250: omap: Move pm_runtime_get_sync

2024-12-05T09:59:40+00:00

commit bcc7ba668818dcadd2f1db66b39ed860a63ecf97 upstream.

Currently in omap_8250_shutdown, the dma->rx_running flag is
set to zero in omap_8250_rx_dma_flush. Next pm_runtime_get_sync
is called, which is a runtime resume call stack which can
re-set the flag. When the call omap_8250_shutdown returns, the
flag is expected to be UN-SET, but this is not the case. This
is causing issues the next time UART is re-opened and
omap_8250_rx_dma is called. Fix by moving pm_runtime_get_sync
before the omap_8250_rx_dma_flush.

cc: stable@vger.kernel.org
Fixes: 0e31c8d173ab ("tty: serial: 8250_omap: add custom DMA-RX callback")
Signed-off-by: Bin Liu 
[Judith: Add commit message]
Signed-off-by: Judith Mendez 
Reviewed-by: Kevin Hilman 
Tested-by: Kevin Hilman 
Link: https://lore.kernel.org/r/20241031172315.453750-1-jm@ti.com
Signed-off-by: Greg Kroah-Hartman

Revert "serial: sh-sci: Clean sci_ports[0] after at earlycon exit"

2024-12-05T09:59:39+00:00

commit 718632467d88e98816fa01ab12681ef1c2aa56f8 upstream.

This reverts commit 3791ea69a4858b81e0277f695ca40f5aae40f312.

It was reported to cause boot-time issues, so revert it for now.

Reported-by: Geert Uytterhoeven 
Fixes: 3791ea69a485 ("serial: sh-sci: Clean sci_ports[0] after at earlycon exit")
Cc: stable 
Cc: Claudiu Beznea 
Signed-off-by: Greg Kroah-Hartman

serial: sh-sci: Clean sci_ports[0] after at earlycon exit

2024-12-05T09:59:39+00:00

commit 3791ea69a4858b81e0277f695ca40f5aae40f312 upstream.

The early_console_setup() function initializes the sci_ports[0].port with
an object of type struct uart_port obtained from the object of type
struct earlycon_device received as argument by the early_console_setup().

It may happen that later, when the rest of the serial ports are probed,
the serial port that was used as earlycon (e.g., port A) to be mapped to a
different position in sci_ports[] and the slot 0 to be used by a different
serial port (e.g., port B), as follows:

sci_ports[0] = port A
sci_ports[X] = port B

In this case, the new port mapped at index zero will have associated data
that was used for earlycon.

In case this happens, after Linux boot, any access to the serial port that
maps on sci_ports[0] (port A) will block the serial port that was used as
earlycon (port B).

To fix this, add early_console_exit() that clean the sci_ports[0] at
earlycon exit time.

Fixes: 0b0cced19ab1 ("serial: sh-sci: Add CONFIG_SERIAL_EARLYCON support")
Cc: stable@vger.kernel.org
Signed-off-by: Claudiu Beznea 
Link: https://lore.kernel.org/r/20241106120118.1719888-4-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman

tty: ldsic: fix tty_ldisc_autoload sysctl's proc_handler

2024-12-05T09:59:39+00:00

commit 635a9fca54f4f4148be1ae1c7c6bd37af80f5773 upstream.

Commit 7c0cca7c847e ("tty: ldisc: add sysctl to prevent autoloading of
ldiscs") introduces the tty_ldisc_autoload sysctl with the wrong
proc_handler. .extra1 and .extra2 parameters are set to avoid other values
thant SYSCTL_ZERO or SYSCTL_ONE to be set but proc_dointvec do not uses
them.

This commit fixes this by using proc_dointvec_minmax instead of
proc_dointvec.

Fixes: 7c0cca7c847e ("tty: ldisc: add sysctl to prevent autoloading of ldiscs")
Cc: stable 
Signed-off-by: Nicolas Bouchinet 
Reviewed-by: Lin Feng 
Reviewed-by: Jiri Slaby 
Link: https://lore.kernel.org/r/20241112131357.49582-4-nicolas.bouchinet@clip-os.org
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Greg Kroah-Hartman

vt: prevent kernel-infoleak in con_font_get()

2024-11-08T15:19:23+00:00

commit f956052e00de211b5c9ebaa1958366c23f82ee9e upstream.

font.data may not initialize all memory spaces depending on the implementation
of vc->vc_sw->con_font_get. This may cause info-leak, so to prevent this, it
is safest to modify it to initialize the allocated memory space to 0, and it
generally does not affect the overall performance of the system.

Cc: stable@vger.kernel.org
Reported-by: syzbot+955da2d57931604ee691@syzkaller.appspotmail.com
Fixes: 05e2600cb0a4 ("VT: Bump font size limitation to 64x128 pixels")
Signed-off-by: Jeongjun Park 
Link: https://lore.kernel.org/r/20241010174619.59662-1-aha310510@gmail.com
Signed-off-by: Greg Kroah-Hartman

tty: rp2: Fix reset with non forgiving PCIe host bridges

2024-11-08T15:19:09+00:00

commit f16dd10ba342c429b1e36ada545fb36d4d1f0e63 upstream.

The write to RP2_GLOBAL_CMD followed by an immediate read of
RP2_GLOBAL_CMD in rp2_reset_asic() is intented to flush out the write,
however by then the device is already in reset and cannot respond to a
memory cycle access.

On platforms such as the Raspberry Pi 4 and others using the
pcie-brcmstb.c driver, any memory access to a device that cannot respond
is met with a fatal system error, rather than being substituted with all
1s as is usually the case on PC platforms.

Swapping the delay and the read ensures that the device has finished
resetting before we attempt to read from it.

Fixes: 7d9f49afa451 ("serial: rp2: New driver for Comtrol RocketPort 2 cards")
Cc: stable 
Suggested-by: Jim Quinlan 
Signed-off-by: Florian Fainelli 
Link: https://lore.kernel.org/r/20240906225435.707837-1-florian.fainelli@broadcom.com
Signed-off-by: Greg Kroah-Hartman

serial: core: check uartclk for zero to avoid divide by zero

2024-08-19T03:32:16+00:00

commit 6eabce6608d6f3440f4c03aa3d3ef50a47a3d193 upstream.

Calling ioctl TIOCSSERIAL with an invalid baud_base can
result in uartclk being zero, which will result in a
divide by zero error in uart_get_divisor(). The check for
uartclk being zero in uart_set_info() needs to be done
before other settings are made as subsequent calls to
ioctl TIOCSSERIAL for the same port would be impacted if
the uartclk check was done where uartclk gets set.

Oops: divide error: 0000  PREEMPT SMP KASAN PTI
RIP: 0010:uart_get_divisor (drivers/tty/serial/serial_core.c:580)
Call Trace:
 
serial8250_get_divisor (drivers/tty/serial/8250/8250_port.c:2576
    drivers/tty/serial/8250/8250_port.c:2589)
serial8250_do_set_termios (drivers/tty/serial/8250/8250_port.c:502
    drivers/tty/serial/8250/8250_port.c:2741)
serial8250_set_termios (drivers/tty/serial/8250/8250_port.c:2862)
uart_change_line_settings (./include/linux/spinlock.h:376
    ./include/linux/serial_core.h:608 drivers/tty/serial/serial_core.c:222)
uart_port_startup (drivers/tty/serial/serial_core.c:342)
uart_startup (drivers/tty/serial/serial_core.c:368)
uart_set_info (drivers/tty/serial/serial_core.c:1034)
uart_set_info_user (drivers/tty/serial/serial_core.c:1059)
tty_set_serial (drivers/tty/tty_io.c:2637)
tty_ioctl (drivers/tty/tty_io.c:2647 drivers/tty/tty_io.c:2791)
__x64_sys_ioctl (fs/ioctl.c:52 fs/ioctl.c:907
    fs/ioctl.c:893 fs/ioctl.c:893)
do_syscall_64 (arch/x86/entry/common.c:52
    (discriminator 1) arch/x86/entry/common.c:83 (discriminator 1))
entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:130)

Reported-by: syzkaller 
Cc: stable@vger.kernel.org
Signed-off-by: George Kennedy 
Rule: add
Link: https://lore.kernel.org/stable/1721148848-9784-1-git-send-email-george.kennedy%40oracle.com
Link: https://lore.kernel.org/r/1721219078-3209-1-git-send-email-george.kennedy@oracle.com
Signed-off-by: Greg Kroah-Hartman

tty: mcf: MCF54418 has 10 UARTS

2024-07-05T07:00:34+00:00

commit 7c92a8bd53f24d50c8cf4aba53bb75505b382fed upstream.

Most of the colfires have up to 5 UARTs but MCF54418 has up-to 10 !
Change the maximum value authorized.

Signed-off-by: Jean-Michel Hautbois 
Cc: stable 
Fixes: 2545cf6e94b4 ("m68knommu: allow 4 coldfire serial ports")
Link: https://lore.kernel.org/r/20240620-upstream-uart-v1-1-a9d0d95fb19e@yoseli.org
Signed-off-by: Greg Kroah-Hartman

serial: sc16is7xx: fix bug in sc16is7xx_set_baud() when using prescaler

2024-07-05T07:00:22+00:00

[ Upstream commit 8492bd91aa055907c67ef04f2b56f6dadd1f44bf ]

When using a high speed clock with a low baud rate, the 4x prescaler is
automatically selected if required. In that case, sc16is7xx_set_baud()
properly configures the chip registers, but returns an incorrect baud
rate by not taking into account the prescaler value. This incorrect baud
rate is then fed to uart_update_timeout().

For example, with an input clock of 80MHz, and a selected baud rate of 50,
sc16is7xx_set_baud() will return 200 instead of 50.

Fix this by first changing the prescaler variable to hold the selected
prescaler value instead of the MCR bitfield. Then properly take into
account the selected prescaler value in the return value computation.

Also add better documentation about the divisor value computation.

Fixes: dfeae619d781 ("serial: sc16is7xx")
Cc: stable@vger.kernel.org
Signed-off-by: Hugo Villeneuve 
Reviewed-by: Jiri Slaby 
Link: https://lore.kernel.org/r/20240430200431.4102923-1-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Sasha Levin

serial: sc16is7xx: replace hardcoded divisor value with BIT() macro

2024-07-05T07:00:21+00:00

[ Upstream commit 2e57cefc4477659527f7adab1f87cdbf60ef1ae6 ]

To better show why the limit is what it is, since we have only 16 bits for
the divisor.

Reviewed-by: Andy Shevchenko 
Suggested-by: Andy Shevchenko 
Signed-off-by: Hugo Villeneuve 
Link: https://lore.kernel.org/r/20231221231823.2327894-13-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman 
Stable-dep-of: 8492bd91aa05 ("serial: sc16is7xx: fix bug in sc16is7xx_set_baud() when using prescaler")
Signed-off-by: Sasha Levin