linux-stable.git/drivers/tty/serial, branch v5.5.7

tty: serial: qcom_geni_serial: Fix RX cancel command failure

2020-02-28T16:23:35+00:00

commit 679aac5ead2f18d223554a52b543e1195e181811 upstream.

RX cancel command fails when BT is switched on and off multiple times.

To handle this, poll for the cancel bit in SE_GENI_S_IRQ_STATUS register
instead of SE_GENI_S_CMD_CTRL_REG.

As per the HPG update, handle the RX last bit after cancel command
and flush out the RX FIFO buffer.

Signed-off-by: satya priya 
Cc: stable 
Link: https://lore.kernel.org/r/1581415982-8793-1-git-send-email-skakit@codeaurora.org
Signed-off-by: Greg Kroah-Hartman

tty: serial: imx: setup the correct sg entry for tx dma

2020-02-28T16:23:35+00:00

commit f76707831829530ffdd3888bebc108aecefccaa0 upstream.

There has oops as below happen on i.MX8MP EVK platform that has
6G bytes DDR memory.

when (xmit->tail < xmit->head) && (xmit->head == 0),
it setups one sg entry with sg->length is zero:
	sg_set_buf(sgl + 1, xmit->buf, xmit->head);

if xmit->buf is allocated from >4G address space, and SDMA only
support <4G address space, then dma_map_sg() will call swiotlb_map()
to do bounce buffer copying and mapping.

But swiotlb_map() don't allow sg entry's length is zero, otherwise
report BUG_ON().

So the patch is to correct the tx DMA scatter list.

Oops:
[  287.675715] kernel BUG at kernel/dma/swiotlb.c:497!
[  287.680592] Internal error: Oops - BUG: 0 [#1] PREEMPT SMP
[  287.686075] Modules linked in:
[  287.689133] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.4.3-00016-g3fdc4e0-dirty #10
[  287.696872] Hardware name: FSL i.MX8MP EVK (DT)
[  287.701402] pstate: 80000085 (Nzcv daIf -PAN -UAO)
[  287.706199] pc : swiotlb_tbl_map_single+0x1fc/0x310
[  287.711076] lr : swiotlb_map+0x60/0x148
[  287.714909] sp : ffff800010003c00
[  287.718221] x29: ffff800010003c00 x28: 0000000000000000
[  287.723533] x27: 0000000000000040 x26: ffff800011ae0000
[  287.728844] x25: ffff800011ae09f8 x24: 0000000000000000
[  287.734155] x23: 00000001b7af9000 x22: 0000000000000000
[  287.739465] x21: ffff000176409c10 x20: 00000000001f7ffe
[  287.744776] x19: ffff000176409c10 x18: 000000000000002e
[  287.750087] x17: 0000000000000000 x16: 0000000000000000
[  287.755397] x15: 0000000000000000 x14: 0000000000000000
[  287.760707] x13: ffff00017f334000 x12: 0000000000000001
[  287.766018] x11: 00000000001fffff x10: 0000000000000000
[  287.771328] x9 : 0000000000000003 x8 : 0000000000000000
[  287.776638] x7 : 0000000000000000 x6 : 0000000000000000
[  287.781949] x5 : 0000000000200000 x4 : 0000000000000000
[  287.787259] x3 : 0000000000000001 x2 : 00000001b7af9000
[  287.792570] x1 : 00000000fbfff000 x0 : 0000000000000000
[  287.797881] Call trace:
[  287.800328]  swiotlb_tbl_map_single+0x1fc/0x310
[  287.804859]  swiotlb_map+0x60/0x148
[  287.808347]  dma_direct_map_page+0xf0/0x130
[  287.812530]  dma_direct_map_sg+0x78/0xe0
[  287.816453]  imx_uart_dma_tx+0x134/0x2f8
[  287.820374]  imx_uart_dma_tx_callback+0xd8/0x168
[  287.824992]  vchan_complete+0x194/0x200
[  287.828828]  tasklet_action_common.isra.0+0x154/0x1a0
[  287.833879]  tasklet_action+0x24/0x30
[  287.837540]  __do_softirq+0x120/0x23c
[  287.841202]  irq_exit+0xb8/0xd8
[  287.844343]  __handle_domain_irq+0x64/0xb8
[  287.848438]  gic_handle_irq+0x5c/0x148
[  287.852185]  el1_irq+0xb8/0x180
[  287.855327]  cpuidle_enter_state+0x84/0x360
[  287.859508]  cpuidle_enter+0x34/0x48
[  287.863083]  call_cpuidle+0x18/0x38
[  287.866571]  do_idle+0x1e0/0x280
[  287.869798]  cpu_startup_entry+0x20/0x40
[  287.873721]  rest_init+0xd4/0xe0
[  287.876949]  arch_call_rest_init+0xc/0x14
[  287.880958]  start_kernel+0x420/0x44c
[  287.884622] Code: 9124c021 9417aff8 a94363f7 17ffffd5 (d4210000)
[  287.890718] ---[ end trace 5bc44c4ab6b009ce ]---
[  287.895334] Kernel panic - not syncing: Fatal exception in interrupt
[  287.901686] SMP: stopping secondary CPUs
[  288.905607] SMP: failed to stop secondary CPUs 0-1
[  288.910395] Kernel Offset: disabled
[  288.913882] CPU features: 0x0002,2000200c
[  288.917888] Memory Limit: none
[  288.920944] ---[ end Kernel panic - not syncing: Fatal exception in interrupt ]---

Reported-by: Eagle Zhou 
Tested-by: Eagle Zhou 
Signed-off-by: Fugang Duan 
Cc: stable 
Fixes: 7942f8577f2a ("serial: imx: TX DMA: clean up sg initialization")
Reviewed-by: Uwe Kleine-König 
Link: https://lore.kernel.org/r/1581401761-6378-1-git-send-email-fugang.duan@nxp.com
Signed-off-by: Greg Kroah-Hartman

tty/serial: atmel: manage shutdown in case of RS485 or ISO7816 mode

2020-02-28T16:23:35+00:00

commit 04b5bfe3dc94e64d0590c54045815cb5183fb095 upstream.

In atmel_shutdown() we call atmel_stop_rx() and atmel_stop_tx() functions.
Prevent the rx restart that is implemented in RS485 or ISO7816 modes when
calling atmel_stop_tx() by using the atomic information tasklet_shutdown
that is already in place for this purpose.

Fixes: 98f2082c3ac4 ("tty/serial: atmel: enforce tasklet init and termination sequences")
Signed-off-by: Nicolas Ferre 
Cc: stable 
Link: https://lore.kernel.org/r/20200210152053.8289-1-nicolas.ferre@microchip.com
Signed-off-by: Greg Kroah-Hartman

serial: 8250: Check UPF_IRQ_SHARED in advance

2020-02-28T16:23:35+00:00

commit 7febbcbc48fc92e3f33863b32ed715ba4aff18c4 upstream.

The commit 54e53b2e8081
  ("tty: serial: 8250: pass IRQ shared flag to UART ports")
nicely explained the problem:

---8<---8<---

On some systems IRQ lines between multiple UARTs might be shared. If so, the
irqflags have to be configured accordingly. The reason is: The 8250 port startup
code performs IRQ tests *before* the IRQ handler for that particular port is
registered. This is performed in serial8250_do_startup(). This function checks
whether IRQF_SHARED is configured and only then disables the IRQ line while
testing.

This test is performed upon each open() of the UART device. Imagine two UARTs
share the same IRQ line: On is already opened and the IRQ is active. When the
second UART is opened, the IRQ line has to be disabled while performing IRQ
tests. Otherwise an IRQ might handler might be invoked, but the IRQ itself
cannot be handled, because the corresponding handler isn't registered,
yet. That's because the 8250 code uses a chain-handler and invokes the
corresponding port's IRQ handling routines himself.

Unfortunately this IRQF_SHARED flag isn't configured for UARTs probed via device
tree even if the IRQs are shared. This way, the actual and shared IRQ line isn't
disabled while performing tests and the kernel correctly detects a spurious
IRQ. So, adding this flag to the DT probe solves the issue.

Note: The UPF_SHARE_IRQ flag is configured unconditionally. Therefore, the
IRQF_SHARED flag can be set unconditionally as well.

Example stack trace by performing `echo 1 > /dev/ttyS2` on a non-patched system:

|irq 85: nobody cared (try booting with the "irqpoll" option)
| [...]
|handlers:
|[] irq_default_primary_handler threaded [] serial8250_interrupt
|Disabling IRQ #85

---8<---8<---

But unfortunately didn't fix the root cause. Let's try again here by moving
IRQ flag assignment from serial_link_irq_chain() to serial8250_do_startup().

This should fix the similar issue reported for 8250_pnp case.

Since this change we don't need to have custom solutions in 8250_aspeed_vuart
and 8250_of drivers, thus, drop them.

Fixes: 1c2f04937b3e ("serial: 8250: add IRQ trigger support")
Reported-by: Li RongQing 
Cc: Kurt Kanzenbach 
Cc: Vikram Pandita 
Signed-off-by: Andy Shevchenko 
Cc: stable 
Acked-by: Kurt Kanzenbach 
Link: https://lore.kernel.org/r/20200211135559.85960-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman

serial: imx: fix a race condition in receive path

2020-02-01T09:32:54+00:00

commit 101aa46bd221b768dfff8ef3745173fc8dbb85ee upstream.

The main irq handler function starts by first masking disabled
interrupts in the status register values to ensure to only handle
enabled interrupts. This is important as when the RX path in the
hardware is disabled reading the RX fifo results in an external abort.

This checking must be done under the port lock, otherwise the following
can happen:

     CPU1                            | CPU2
                                     |
     irq triggers as there are chars |
     in the RX fifo                  |
				     | grab port lock
     imx_uart_int finds RRDY enabled |
     and calls imx_uart_rxint which  |
     has to wait for port lock       |
                                     | disable RX (e.g. because we're
                                     | using RS485 with !RX_DURING_TX)
                                     |
                                     | release port lock
     read from RX fifo with RX       |
     disabled => exception           |

So take the port lock only once in imx_uart_int() instead of in the
functions called from there.

Reported-by: Andre Renaud 
Cc: stable@vger.kernel.org
Signed-off-by: Uwe Kleine-König 
Link: https://lore.kernel.org/r/20200121071702.20150-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman

serial: 8250_bcm2835aux: Fix line mismatch on driver unbind

2020-02-01T09:32:53+00:00

commit dc76697d7e933d5e299116f219c890568785ea15 upstream.

Unbinding the bcm2835aux UART driver raises the following error if the
maximum number of 8250 UARTs is set to 1 (via the 8250.nr_uarts module
parameter or CONFIG_SERIAL_8250_RUNTIME_UARTS):

(NULL device *): Removing wrong port: a6f80333 != fa20408b

That's because bcm2835aux_serial_probe() retrieves UART line number 1
from the devicetree and stores it in data->uart.port.line, while
serial8250_register_8250_port() instead uses UART line number 0,
which is stored in data->line.

On driver unbind, bcm2835aux_serial_remove() uses data->uart.port.line,
which contains the wrong number.  Fix it.

The issue does not occur if the maximum number of 8250 UARTs is >= 2.

Fixes: bdc5f3009580 ("serial: bcm2835: add driver for bcm2835-aux-uart")
Signed-off-by: Lukas Wunner 
Cc: stable@vger.kernel.org # v4.6+
Cc: Martin Sperl 
Reviewed-by: Nicolas Saenz Julienne 
Tested-by: Nicolas Saenz Julienne 
Link: https://lore.kernel.org/r/912ccf553c5258135c6d7e8f404a101ef320f0f4.1579175223.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman

tty/serial: atmel: fix out of range clock divider handling

2019-12-17T13:17:32+00:00

Use MCK_DIV8 when the clock divider is > 65535. Unfortunately the mode
register was already written thus the clock selection is ignored.

Fix by doing the baud rate calulation before setting the mode.

Fixes: 5bf5635ac170 ("tty/serial: atmel: add fractional baud rate support")
Signed-off-by: David Engraf 
Acked-by: Ludovic Desroches 
Acked-by: Richard Genoud 
Cc: stable 
Link: https://lore.kernel.org/r/20191216085403.17050-1-david.engraf@sysgo.com
Signed-off-by: Greg Kroah-Hartman

tty: link tty and port before configuring it as console

2019-12-17T13:12:34+00:00

There seems to be a race condition in tty drivers and I could see on
many boot cycles a NULL pointer dereference as tty_init_dev() tries to
do 'tty->port->itty = tty' even though tty->port is NULL.
'tty->port' will be set by the driver and if the driver has not yet done
it before we open the tty device we can get to this situation. By adding
some extra debug prints, I noticed that:

6.650130: uart_add_one_port
6.663849: register_console
6.664846: tty_open
6.674391: tty_init_dev
6.675456: tty_port_link_device

uart_add_one_port() registers the console, as soon as it registers, the
userspace tries to use it and that leads to tty_open() but
uart_add_one_port() has not yet done tty_port_link_device() and so
tty->port is not yet configured when control reaches tty_init_dev().

Further look into the code and tty_port_link_device() is done by
uart_add_one_port(). After registering the console uart_add_one_port()
will call tty_port_register_device_attr_serdev() and
tty_port_link_device() is called from this.

Call add tty_port_link_device() before uart_configure_port() is done and
add a check in tty_port_link_device() so that it only links the port if
it has not been done yet.

Suggested-by: Jiri Slaby 
Signed-off-by: Sudip Mukherjee 
Cc: stable 
Link: https://lore.kernel.org/r/20191212131602.29504-1-sudipm.mukherjee@gmail.com
Signed-off-by: Greg Kroah-Hartman

serial: sprd: Add clearing break interrupt operation

2019-12-12T13:26:59+00:00

A break interrupt will be generated if the RX line was pulled low, which
means some abnomal behaviors occurred of the UART. In this case, we still
need to clear this break interrupt status, otherwise it will cause irq
storm to crash the whole system.

Fixes: b7396a38fb28 ("tty/serial: Add Spreadtrum sc9836-uart driver support")
Signed-off-by: Yonghan Ye 
Cc: stable 
Signed-off-by: Baolin Wang 
Link: https://lore.kernel.org/r/925e51b73099c90158e080b8f5bed9b3b38c4548.1575460601.git.baolin.wang7@gmail.com
Signed-off-by: Greg Kroah-Hartman

tty: serial: msm_serial: Fix lockup for sysrq and oops

2019-12-12T13:26:59+00:00

As the commit 677fe555cbfb ("serial: imx: Fix recursive locking bug")
has mentioned the uart driver might cause recursive locking between
normal printing and the kernel debugging facilities (e.g. sysrq and
oops).  In the commit it gave out suggestion for fixing recursive
locking issue: "The solution is to avoid locking in the sysrq case
and trylock in the oops_in_progress case."

This patch follows the suggestion (also used the exactly same code with
other serial drivers, e.g. amba-pl011.c) to fix the recursive locking
issue, this can avoid stuck caused by deadlock and print out log for
sysrq and oops.

Fixes: 04896a77a97b ("msm_serial: serial driver for MSM7K onboard serial peripheral.")
Signed-off-by: Leo Yan 
Reviewed-by: Jeffrey Hugo 
Link: https://lore.kernel.org/r/20191127141544.4277-2-leo.yan@linaro.org
Signed-off-by: Greg Kroah-Hartman