linux-stable.git/drivers/tty/serial, branch v5.4.74

serial: pl011: Fix lockdep splat when handling magic-sysrq interrupt

2020-11-01T11:01:06+00:00

commit 534cf755d9df99e214ddbe26b91cd4d81d2603e2 upstream.

Issuing a magic-sysrq via the PL011 causes the following lockdep splat,
which is easily reproducible under QEMU:

  | sysrq: Changing Loglevel
  | sysrq: Loglevel set to 9
  |
  | ======================================================
  | WARNING: possible circular locking dependency detected
  | 5.9.0-rc7 #1 Not tainted
  | ------------------------------------------------------
  | systemd-journal/138 is trying to acquire lock:
  | ffffab133ad950c0 (console_owner){-.-.}-{0:0}, at: console_lock_spinning_enable+0x34/0x70
  |
  | but task is already holding lock:
  | ffff0001fd47b098 (&port_lock_key){-.-.}-{2:2}, at: pl011_int+0x40/0x488
  |
  | which lock already depends on the new lock.

  [...]

  |  Possible unsafe locking scenario:
  |
  |        CPU0                    CPU1
  |        ----                    ----
  |   lock(&port_lock_key);
  |                                lock(console_owner);
  |                                lock(&port_lock_key);
  |   lock(console_owner);
  |
  |  *** DEADLOCK ***

The issue being that CPU0 takes 'port_lock' on the irq path in pl011_int()
before taking 'console_owner' on the printk() path, whereas CPU1 takes
the two locks in the opposite order on the printk() path due to setting
the "console_owner" prior to calling into into the actual console driver.

Fix this in the same way as the msm-serial driver by dropping 'port_lock'
before handling the sysrq.

Cc:  # 4.19+
Cc: Russell King 
Cc: Greg Kroah-Hartman 
Cc: Jiri Slaby 
Link: https://lore.kernel.org/r/20200811101313.GA6970@willie-the-truck
Signed-off-by: Peter Zijlstra 
Tested-by: Will Deacon 
Signed-off-by: Will Deacon 
Link: https://lore.kernel.org/r/20200930120432.16551-1-will@kernel.org
Signed-off-by: Greg Kroah-Hartman

serial: qcom_geni_serial: To correct QUP Version detection logic

2020-11-01T11:01:06+00:00

commit c9ca43d42ed8d5fd635d327a664ed1d8579eb2af upstream.

For QUP IP versions 2.5 and above the oversampling rate is
halved from 32 to 16.

Commit ce734600545f ("tty: serial: qcom_geni_serial: Update
the oversampling rate") is pushed to handle this scenario.
But the existing logic is failing to classify QUP Version 3.0
into the correct group ( 2.5 and above).

As result Serial Engine clocks are not configured properly for
baud rate and garbage data is sampled to FIFOs from the line.

So, fix the logic to detect QUP with versions 2.5 and above.

Fixes: ce734600545f ("tty: serial: qcom_geni_serial: Update the oversampling rate")
Cc: stable 
Signed-off-by: Paras Sharma 
Reviewed-by: Akash Asthana 
Link: https://lore.kernel.org/r/1601445926-23673-1-git-send-email-parashar@codeaurora.org
Signed-off-by: Greg Kroah-Hartman

tty: serial: fsl_lpuart: fix lpuart32_poll_get_char

2020-10-29T08:58:10+00:00

commit 29788ab1d2bf26c130de8f44f9553ee78a27e8d5 upstream.

The watermark is set to 1, so we need to input two chars to trigger RDRF
using the original logic. With the new logic, we could always get the
char when there is data in FIFO.

Suggested-by: Fugang Duan 
Signed-off-by: Peng Fan 
Link: https://lore.kernel.org/r/20200929095509.21680-1-peng.fan@nxp.com
Cc: stable 
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Greg Kroah-Hartman

tty: serial: lpuart: fix lpuart32_write usage

2020-10-29T08:58:10+00:00

commit 9ea40db477c024dcb87321b7f32bd6ea12130ac2 upstream.

The 2nd and 3rd parameter were wrongly used, and cause kernel abort when
doing kgdb debug.

Fixes: 1da17d7cf8e2 ("tty: serial: fsl_lpuart: Use appropriate lpuart32_* I/O funcs")
Cc: stable 
Signed-off-by: Peng Fan 
Link: https://lore.kernel.org/r/20200929091920.22612-1-peng.fan@nxp.com
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Greg Kroah-Hartman

tty: serial: earlycon dependency

2020-10-29T08:57:37+00:00

[ Upstream commit 0fb9342d06b0f667b915ba58bfefc030e534a218 ]

parse_options() in drivers/tty/serial/earlycon.c calls uart_parse_earlycon
in drivers/tty/serial/serial_core.c therefore selecting SERIAL_EARLYCON
should automatically select SERIAL_CORE, otherwise will result in symbol
not found error during linking if SERIAL_CORE is not configured as builtin

Fixes: 9aac5887595b ("tty/serial: add generic serial earlycon")
Signed-off-by: Tong Zhang 
Link: https://lore.kernel.org/r/20200828123949.2642-1-ztong0001@gmail.com
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Sasha Levin

tty: serial: samsung: Correct clock selection logic

2020-10-01T11:18:00+00:00

[ Upstream commit 7d31676a8d91dd18e08853efd1cb26961a38c6a6 ]

Some variants of the samsung tty driver can pick which clock
to use for their baud rate generation.  In the DT conversion,
a default clock was selected to be used if a specific one wasn't
assigned and then a comparison of which clock rate worked better
was done.  Unfortunately, the comparison was implemented in such
a way that only the default clock was ever actually compared.
Fix this by iterating through all possible clocks, except when a
specific clock has already been picked via clk_sel (which is
only possible via board files).

Signed-off-by: Jonathan Bakker 
Reviewed-by: Krzysztof Kozlowski 
Link: https://lore.kernel.org/r/BN6PR04MB06604E63833EA41837EBF77BA3A30@BN6PR04MB0660.namprd04.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Sasha Levin

serial: uartps: Wait for tx_empty in console setup

2020-10-01T11:17:55+00:00

[ Upstream commit 42e11948ddf68b9f799cad8c0ddeab0a39da33e8 ]

On some platforms, the log is corrupted while console is being
registered. It is observed that when set_termios is called, there
are still some bytes in the FIFO to be transmitted.

So, wait for tx_empty inside cdns_uart_console_setup before calling
set_termios.

Signed-off-by: Raviteja Narayanam 
Reviewed-by: Shubhrajyoti Datta 
Link: https://lore.kernel.org/r/1586413563-29125-2-git-send-email-raviteja.narayanam@xilinx.com
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Sasha Levin

serial: 8250: 8250_omap: Terminate DMA before pushing data on RX timeout

2020-10-01T11:17:46+00:00

[ Upstream commit 7cf4df30a98175033e9849f7f16c46e96ba47f41 ]

Terminate and flush DMA internal buffers, before pushing RX data to
higher layer. Otherwise, this will lead to data corruption, as driver
would end up pushing stale buffer data to higher layer while actual data
is still stuck inside DMA hardware and has yet not arrived at the
memory.
While at that, replace deprecated dmaengine_terminate_all() with
dmaengine_terminate_async().

Signed-off-by: Vignesh Raghavendra 
Link: https://lore.kernel.org/r/20200319110344.21348-2-vigneshr@ti.com
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Sasha Levin

serial: 8250_omap: Fix sleeping function called from invalid context during probe

2020-10-01T11:17:46+00:00

[ Upstream commit 4ce35a3617c0ac758c61122b2218b6c8c9ac9398 ]

When booting j721e the following bug is printed:

[    1.154821] BUG: sleeping function called from invalid context at kernel/sched/completion.c:99
[    1.154827] in_atomic(): 0, irqs_disabled(): 128, non_block: 0, pid: 12, name: kworker/0:1
[    1.154832] 3 locks held by kworker/0:1/12:
[    1.154836]  #0: ffff000840030728 ((wq_completion)events){+.+.}, at: process_one_work+0x1d4/0x6e8
[    1.154852]  #1: ffff80001214fdd8 (deferred_probe_work){+.+.}, at: process_one_work+0x1d4/0x6e8
[    1.154860]  #2: ffff00084060b170 (&dev->mutex){....}, at: __device_attach+0x38/0x138
[    1.154872] irq event stamp: 63096
[    1.154881] hardirqs last  enabled at (63095): [] _raw_spin_unlock_irqrestore+0x70/0x78
[    1.154887] hardirqs last disabled at (63096): [] _raw_spin_lock_irqsave+0x28/0x80
[    1.154893] softirqs last  enabled at (62254): [] _stext+0x488/0x564
[    1.154899] softirqs last disabled at (62247): [] irq_exit+0x114/0x140
[    1.154906] CPU: 0 PID: 12 Comm: kworker/0:1 Not tainted 5.6.0-rc6-next-20200318-00094-g45e4089b0bd3 #221
[    1.154911] Hardware name: Texas Instruments K3 J721E SoC (DT)
[    1.154917] Workqueue: events deferred_probe_work_func
[    1.154923] Call trace:
[    1.154928]  dump_backtrace+0x0/0x190
[    1.154933]  show_stack+0x14/0x20
[    1.154940]  dump_stack+0xe0/0x148
[    1.154946]  ___might_sleep+0x150/0x1f0
[    1.154952]  __might_sleep+0x4c/0x80
[    1.154957]  wait_for_completion_timeout+0x40/0x140
[    1.154964]  ti_sci_set_device_state+0xa0/0x158
[    1.154969]  ti_sci_cmd_get_device_exclusive+0x14/0x20
[    1.154977]  ti_sci_dev_start+0x34/0x50
[    1.154984]  genpd_runtime_resume+0x78/0x1f8
[    1.154991]  __rpm_callback+0x3c/0x140
[    1.154996]  rpm_callback+0x20/0x80
[    1.155001]  rpm_resume+0x568/0x758
[    1.155007]  __pm_runtime_resume+0x44/0xb0
[    1.155013]  omap8250_probe+0x2b4/0x508
[    1.155019]  platform_drv_probe+0x50/0xa0
[    1.155023]  really_probe+0xd4/0x318
[    1.155028]  driver_probe_device+0x54/0xe8
[    1.155033]  __device_attach_driver+0x80/0xb8
[    1.155039]  bus_for_each_drv+0x74/0xc0
[    1.155044]  __device_attach+0xdc/0x138
[    1.155049]  device_initial_probe+0x10/0x18
[    1.155053]  bus_probe_device+0x98/0xa0
[    1.155058]  deferred_probe_work_func+0x74/0xb0
[    1.155063]  process_one_work+0x280/0x6e8
[    1.155068]  worker_thread+0x48/0x430
[    1.155073]  kthread+0x108/0x138
[    1.155079]  ret_from_fork+0x10/0x18

To fix the bug we need to first call pm_runtime_enable() prior to any
pm_runtime calls.

Reported-by: Tomi Valkeinen 
Signed-off-by: Peter Ujfalusi 
Link: https://lore.kernel.org/r/20200320125200.6772-1-peter.ujfalusi@ti.com
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Sasha Levin

serial: 8250_port: Don't service RX FIFO if throttled

2020-10-01T11:17:46+00:00

[ Upstream commit f19c3f6c8109b8bab000afd35580929958e087a9 ]

When port's throttle callback is called, it should stop pushing any more
data into TTY buffer to avoid buffer overflow. This means driver has to
stop HW from receiving more data and assert the HW flow control. For
UARTs with auto HW flow control (such as 8250_omap) manual assertion of
flow control line is not possible and only way is to allow RX FIFO to
fill up, thus trigger auto HW flow control logic.

Therefore make sure that 8250 generic IRQ handler does not drain data
when port is stopped (i.e UART_LSR_DR is unset in read_status_mask). Not
servicing, RX FIFO would trigger auto HW flow control when FIFO
occupancy reaches preset threshold, thus halting RX.
Since, error conditions in UART_LSR register are cleared just by reading
the register, data has to be drained in case there are FIFO errors, else
error information will lost.

Signed-off-by: Vignesh Raghavendra 
Link: https://lore.kernel.org/r/20200319103230.16867-2-vigneshr@ti.com
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Sasha Levin