linux-stable.git/drivers/tty/serial, branch v5.4.71 Linux kernel stable tree tty: serial: samsung: Correct clock selection logic 2020-10-01T11:18:00+00:00 Jonathan Bakker xc-racer2@live.ca 2020-05-09T01:34:33+00:00 942a6ff2146a9d65ba3c13822143827c6ad31d59 [ Upstream commit 7d31676a8d91dd18e08853efd1cb26961a38c6a6 ] Some variants of the samsung tty driver can pick which clock to use for their baud rate generation. In the DT conversion, a default clock was selected to be used if a specific one wasn't assigned and then a comparison of which clock rate worked better was done. Unfortunately, the comparison was implemented in such a way that only the default clock was ever actually compared. Fix this by iterating through all possible clocks, except when a specific clock has already been picked via clk_sel (which is only possible via board files). Signed-off-by: Jonathan Bakker <xc-racer2@live.ca> Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org> Link: https://lore.kernel.org/r/BN6PR04MB06604E63833EA41837EBF77BA3A30@BN6PR04MB0660.namprd04.prod.outlook.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit 7d31676a8d91dd18e08853efd1cb26961a38c6a6 ]

Some variants of the samsung tty driver can pick which clock
to use for their baud rate generation.  In the DT conversion,
a default clock was selected to be used if a specific one wasn't
assigned and then a comparison of which clock rate worked better
was done.  Unfortunately, the comparison was implemented in such
a way that only the default clock was ever actually compared.
Fix this by iterating through all possible clocks, except when a
specific clock has already been picked via clk_sel (which is
only possible via board files).

Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/BN6PR04MB06604E63833EA41837EBF77BA3A30@BN6PR04MB0660.namprd04.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
serial: uartps: Wait for tx_empty in console setup 2020-10-01T11:17:55+00:00 Raviteja Narayanam raviteja.narayanam@xilinx.com 2020-04-09T06:26:02+00:00 26d261f32f43253e0fcd781cdee4d1eda79f672c [ Upstream commit 42e11948ddf68b9f799cad8c0ddeab0a39da33e8 ] On some platforms, the log is corrupted while console is being registered. It is observed that when set_termios is called, there are still some bytes in the FIFO to be transmitted. So, wait for tx_empty inside cdns_uart_console_setup before calling set_termios. Signed-off-by: Raviteja Narayanam <raviteja.narayanam@xilinx.com> Reviewed-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com> Link: https://lore.kernel.org/r/1586413563-29125-2-git-send-email-raviteja.narayanam@xilinx.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit 42e11948ddf68b9f799cad8c0ddeab0a39da33e8 ]

On some platforms, the log is corrupted while console is being
registered. It is observed that when set_termios is called, there
are still some bytes in the FIFO to be transmitted.

So, wait for tx_empty inside cdns_uart_console_setup before calling
set_termios.

Signed-off-by: Raviteja Narayanam <raviteja.narayanam@xilinx.com>
Reviewed-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Link: https://lore.kernel.org/r/1586413563-29125-2-git-send-email-raviteja.narayanam@xilinx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
serial: 8250: 8250_omap: Terminate DMA before pushing data on RX timeout 2020-10-01T11:17:46+00:00 Vignesh Raghavendra vigneshr@ti.com 2020-03-19T11:03:39+00:00 47e276e1c40ebbda39143a7ac87254d5078cb9a9 [ Upstream commit 7cf4df30a98175033e9849f7f16c46e96ba47f41 ] Terminate and flush DMA internal buffers, before pushing RX data to higher layer. Otherwise, this will lead to data corruption, as driver would end up pushing stale buffer data to higher layer while actual data is still stuck inside DMA hardware and has yet not arrived at the memory. While at that, replace deprecated dmaengine_terminate_all() with dmaengine_terminate_async(). Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com> Link: https://lore.kernel.org/r/20200319110344.21348-2-vigneshr@ti.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit 7cf4df30a98175033e9849f7f16c46e96ba47f41 ]

Terminate and flush DMA internal buffers, before pushing RX data to
higher layer. Otherwise, this will lead to data corruption, as driver
would end up pushing stale buffer data to higher layer while actual data
is still stuck inside DMA hardware and has yet not arrived at the
memory.
While at that, replace deprecated dmaengine_terminate_all() with
dmaengine_terminate_async().

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20200319110344.21348-2-vigneshr@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
serial: 8250_omap: Fix sleeping function called from invalid context during probe 2020-10-01T11:17:46+00:00 Peter Ujfalusi peter.ujfalusi@ti.com 2020-03-20T12:52:00+00:00 09a2cf6771059fbc49f26bc26b1d582e04a75ea6 [ Upstream commit 4ce35a3617c0ac758c61122b2218b6c8c9ac9398 ] When booting j721e the following bug is printed: [ 1.154821] BUG: sleeping function called from invalid context at kernel/sched/completion.c:99 [ 1.154827] in_atomic(): 0, irqs_disabled(): 128, non_block: 0, pid: 12, name: kworker/0:1 [ 1.154832] 3 locks held by kworker/0:1/12: [ 1.154836] #0: ffff000840030728 ((wq_completion)events){+.+.}, at: process_one_work+0x1d4/0x6e8 [ 1.154852] #1: ffff80001214fdd8 (deferred_probe_work){+.+.}, at: process_one_work+0x1d4/0x6e8 [ 1.154860] #2: ffff00084060b170 (&dev->mutex){....}, at: __device_attach+0x38/0x138 [ 1.154872] irq event stamp: 63096 [ 1.154881] hardirqs last enabled at (63095): [<ffff800010b74318>] _raw_spin_unlock_irqrestore+0x70/0x78 [ 1.154887] hardirqs last disabled at (63096): [<ffff800010b740d8>] _raw_spin_lock_irqsave+0x28/0x80 [ 1.154893] softirqs last enabled at (62254): [<ffff800010080c88>] _stext+0x488/0x564 [ 1.154899] softirqs last disabled at (62247): [<ffff8000100fdb3c>] irq_exit+0x114/0x140 [ 1.154906] CPU: 0 PID: 12 Comm: kworker/0:1 Not tainted 5.6.0-rc6-next-20200318-00094-g45e4089b0bd3 #221 [ 1.154911] Hardware name: Texas Instruments K3 J721E SoC (DT) [ 1.154917] Workqueue: events deferred_probe_work_func [ 1.154923] Call trace: [ 1.154928] dump_backtrace+0x0/0x190 [ 1.154933] show_stack+0x14/0x20 [ 1.154940] dump_stack+0xe0/0x148 [ 1.154946] ___might_sleep+0x150/0x1f0 [ 1.154952] __might_sleep+0x4c/0x80 [ 1.154957] wait_for_completion_timeout+0x40/0x140 [ 1.154964] ti_sci_set_device_state+0xa0/0x158 [ 1.154969] ti_sci_cmd_get_device_exclusive+0x14/0x20 [ 1.154977] ti_sci_dev_start+0x34/0x50 [ 1.154984] genpd_runtime_resume+0x78/0x1f8 [ 1.154991] __rpm_callback+0x3c/0x140 [ 1.154996] rpm_callback+0x20/0x80 [ 1.155001] rpm_resume+0x568/0x758 [ 1.155007] __pm_runtime_resume+0x44/0xb0 [ 1.155013] omap8250_probe+0x2b4/0x508 [ 1.155019] platform_drv_probe+0x50/0xa0 [ 1.155023] really_probe+0xd4/0x318 [ 1.155028] driver_probe_device+0x54/0xe8 [ 1.155033] __device_attach_driver+0x80/0xb8 [ 1.155039] bus_for_each_drv+0x74/0xc0 [ 1.155044] __device_attach+0xdc/0x138 [ 1.155049] device_initial_probe+0x10/0x18 [ 1.155053] bus_probe_device+0x98/0xa0 [ 1.155058] deferred_probe_work_func+0x74/0xb0 [ 1.155063] process_one_work+0x280/0x6e8 [ 1.155068] worker_thread+0x48/0x430 [ 1.155073] kthread+0x108/0x138 [ 1.155079] ret_from_fork+0x10/0x18 To fix the bug we need to first call pm_runtime_enable() prior to any pm_runtime calls. Reported-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Link: https://lore.kernel.org/r/20200320125200.6772-1-peter.ujfalusi@ti.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit 4ce35a3617c0ac758c61122b2218b6c8c9ac9398 ]

When booting j721e the following bug is printed:

[    1.154821] BUG: sleeping function called from invalid context at kernel/sched/completion.c:99
[    1.154827] in_atomic(): 0, irqs_disabled(): 128, non_block: 0, pid: 12, name: kworker/0:1
[    1.154832] 3 locks held by kworker/0:1/12:
[    1.154836]  #0: ffff000840030728 ((wq_completion)events){+.+.}, at: process_one_work+0x1d4/0x6e8
[    1.154852]  #1: ffff80001214fdd8 (deferred_probe_work){+.+.}, at: process_one_work+0x1d4/0x6e8
[    1.154860]  #2: ffff00084060b170 (&dev->mutex){....}, at: __device_attach+0x38/0x138
[    1.154872] irq event stamp: 63096
[    1.154881] hardirqs last  enabled at (63095): [<ffff800010b74318>] _raw_spin_unlock_irqrestore+0x70/0x78
[    1.154887] hardirqs last disabled at (63096): [<ffff800010b740d8>] _raw_spin_lock_irqsave+0x28/0x80
[    1.154893] softirqs last  enabled at (62254): [<ffff800010080c88>] _stext+0x488/0x564
[    1.154899] softirqs last disabled at (62247): [<ffff8000100fdb3c>] irq_exit+0x114/0x140
[    1.154906] CPU: 0 PID: 12 Comm: kworker/0:1 Not tainted 5.6.0-rc6-next-20200318-00094-g45e4089b0bd3 #221
[    1.154911] Hardware name: Texas Instruments K3 J721E SoC (DT)
[    1.154917] Workqueue: events deferred_probe_work_func
[    1.154923] Call trace:
[    1.154928]  dump_backtrace+0x0/0x190
[    1.154933]  show_stack+0x14/0x20
[    1.154940]  dump_stack+0xe0/0x148
[    1.154946]  ___might_sleep+0x150/0x1f0
[    1.154952]  __might_sleep+0x4c/0x80
[    1.154957]  wait_for_completion_timeout+0x40/0x140
[    1.154964]  ti_sci_set_device_state+0xa0/0x158
[    1.154969]  ti_sci_cmd_get_device_exclusive+0x14/0x20
[    1.154977]  ti_sci_dev_start+0x34/0x50
[    1.154984]  genpd_runtime_resume+0x78/0x1f8
[    1.154991]  __rpm_callback+0x3c/0x140
[    1.154996]  rpm_callback+0x20/0x80
[    1.155001]  rpm_resume+0x568/0x758
[    1.155007]  __pm_runtime_resume+0x44/0xb0
[    1.155013]  omap8250_probe+0x2b4/0x508
[    1.155019]  platform_drv_probe+0x50/0xa0
[    1.155023]  really_probe+0xd4/0x318
[    1.155028]  driver_probe_device+0x54/0xe8
[    1.155033]  __device_attach_driver+0x80/0xb8
[    1.155039]  bus_for_each_drv+0x74/0xc0
[    1.155044]  __device_attach+0xdc/0x138
[    1.155049]  device_initial_probe+0x10/0x18
[    1.155053]  bus_probe_device+0x98/0xa0
[    1.155058]  deferred_probe_work_func+0x74/0xb0
[    1.155063]  process_one_work+0x280/0x6e8
[    1.155068]  worker_thread+0x48/0x430
[    1.155073]  kthread+0x108/0x138
[    1.155079]  ret_from_fork+0x10/0x18

To fix the bug we need to first call pm_runtime_enable() prior to any
pm_runtime calls.

Reported-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20200320125200.6772-1-peter.ujfalusi@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
serial: 8250_port: Don't service RX FIFO if throttled 2020-10-01T11:17:46+00:00 Vignesh Raghavendra vigneshr@ti.com 2020-03-19T10:32:29+00:00 93ec0b575aca57e663e0ba881e65aa06df2b1a2d [ Upstream commit f19c3f6c8109b8bab000afd35580929958e087a9 ] When port's throttle callback is called, it should stop pushing any more data into TTY buffer to avoid buffer overflow. This means driver has to stop HW from receiving more data and assert the HW flow control. For UARTs with auto HW flow control (such as 8250_omap) manual assertion of flow control line is not possible and only way is to allow RX FIFO to fill up, thus trigger auto HW flow control logic. Therefore make sure that 8250 generic IRQ handler does not drain data when port is stopped (i.e UART_LSR_DR is unset in read_status_mask). Not servicing, RX FIFO would trigger auto HW flow control when FIFO occupancy reaches preset threshold, thus halting RX. Since, error conditions in UART_LSR register are cleared just by reading the register, data has to be drained in case there are FIFO errors, else error information will lost. Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com> Link: https://lore.kernel.org/r/20200319103230.16867-2-vigneshr@ti.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit f19c3f6c8109b8bab000afd35580929958e087a9 ]

When port's throttle callback is called, it should stop pushing any more
data into TTY buffer to avoid buffer overflow. This means driver has to
stop HW from receiving more data and assert the HW flow control. For
UARTs with auto HW flow control (such as 8250_omap) manual assertion of
flow control line is not possible and only way is to allow RX FIFO to
fill up, thus trigger auto HW flow control logic.

Therefore make sure that 8250 generic IRQ handler does not drain data
when port is stopped (i.e UART_LSR_DR is unset in read_status_mask). Not
servicing, RX FIFO would trigger auto HW flow control when FIFO
occupancy reaches preset threshold, thus halting RX.
Since, error conditions in UART_LSR register are cleared just by reading
the register, data has to be drained in case there are FIFO errors, else
error information will lost.

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20200319103230.16867-2-vigneshr@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
tty: sifive: Finish transmission before changing the clock 2020-10-01T11:17:42+00:00 Palmer Dabbelt palmerdabbelt@google.com 2020-03-07T04:26:38+00:00 b1f5989a23c1d06f834a051fbeea4cfc65c58668 [ Upstream commit 4cbd7814bbd595061fcb6d6355d63f04179161cd ] SiFive's UART has a software controller clock divider that produces the final baud rate clock. Whenever the clock that drives the UART is changed this divider must be updated accordingly, and given that these two events are controlled by software they cannot be done atomically. During the period between updating the UART's driving clock and internal divider the UART will transmit a different baud rate than what the user has configured, which will probably result in a corrupted transmission stream. The SiFive UART has a FIFO, but due to an issue with the programming interface there is no way to directly determine when the UART has finished transmitting. We're essentially restricted to dead reckoning in order to figure that out: we can use the FIFO's TX busy register to figure out when the last frame has begun transmission and just delay for a long enough that the last frame is guaranteed to get out. As far as the actual implementation goes: I've modified the existing existing clock notifier function to drain both the FIFO and the shift register in on PRE_RATE_CHANGE. As far as I know there is no hardware flow control in this UART, so there's no good way to ask the other end to stop transmission while we can't receive (inserting software flow control messages seems like a bad idea here). Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com> Tested-by: Yash Shah <yash.shah@sifive.com> Link: https://lore.kernel.org/r/20200307042637.83728-1-palmer@dabbelt.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit 4cbd7814bbd595061fcb6d6355d63f04179161cd ]

SiFive's UART has a software controller clock divider that produces the
final baud rate clock.  Whenever the clock that drives the UART is
changed this divider must be updated accordingly, and given that these
two events are controlled by software they cannot be done atomically.
During the period between updating the UART's driving clock and internal
divider the UART will transmit a different baud rate than what the user
has configured, which will probably result in a corrupted transmission
stream.

The SiFive UART has a FIFO, but due to an issue with the programming
interface there is no way to directly determine when the UART has
finished transmitting.  We're essentially restricted to dead reckoning
in order to figure that out: we can use the FIFO's TX busy register to
figure out when the last frame has begun transmission and just delay for
a long enough that the last frame is guaranteed to get out.

As far as the actual implementation goes: I've modified the existing
existing clock notifier function to drain both the FIFO and the shift
register in on PRE_RATE_CHANGE.  As far as I know there is no hardware
flow control in this UART, so there's no good way to ask the other end
to stop transmission while we can't receive (inserting software flow
control messages seems like a bad idea here).

Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Tested-by: Yash Shah <yash.shah@sifive.com>
Link: https://lore.kernel.org/r/20200307042637.83728-1-palmer@dabbelt.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
serial: 8250_pci: Add Realtek 816a and 816b 2020-09-23T10:40:45+00:00 Tobias Diedrich tobiasdiedrich@gmail.com 2020-09-14T17:36:28+00:00 b703bd1e9285a5d5db6b232f14fa2150a1432cda commit 3c5a87be170aba8ac40982182f812dcff6ed1ad1 upstream. These serial ports are exposed by the OOB-management-engine on RealManage-enabled network cards (e.g. AMD DASH enabled systems using Realtek cards). Because these have 3 BARs, they fail the "num_iomem <= 1" check in serial_pci_guess_board. I've manually checked the two IOMEM regions and BAR 2 doesn't seem to respond to reads, but BAR 4 seems to be an MMIO version of the IO ports (untested). With this change, the ports are detected: 0000:02:00.1: ttyS0 at I/O 0x2200 (irq = 82, base_baud = 115200) is a 16550A 0000:02:00.2: ttyS1 at I/O 0x2100 (irq = 55, base_baud = 115200) is a 16550A lspci output: 02:00.1 0700: 10ec:816a (rev 0e) (prog-if 02 [16550]) Subsystem: 17aa:5082 Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort+ <TAbort- <MAbort- >SERR- <PERR- INTx- Interrupt: pin B routed to IRQ 82 IOMMU group: 11 Region 0: I/O ports at 2200 [size=256] Region 2: Memory at fd715000 (64-bit, non-prefetchable) [size=4K] Region 4: Memory at fd704000 (64-bit, non-prefetchable) [size=16K] Capabilities: [40] Power Management version 3 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME- Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit+ Address: 0000000000000000 Data: 0000 Capabilities: [70] Express (v2) Endpoint, MSI 01 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s unlimited, L1 <64us ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset- SlotPowerLimit 0.000W DevCtl: CorrErr- NonFatalErr- FatalErr- UnsupReq- RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 512 bytes DevSta: CorrErr+ NonFatalErr- FatalErr- UnsupReq+ AuxPwr+ TransPend- LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s unlimited, L1 <64us ClockPM+ Surprise- LLActRep- BwNot- ASPMOptComp+ LnkCtl: ASPM L1 Enabled; RCB 64 bytes, Disabled- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s (ok), Width x1 (ok) TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- DevCap2: Completion Timeout: Range ABCD, TimeoutDis+ NROPrPrP- LTR+ 10BitTagComp- 10BitTagReq- OBFF Via message/WAKE#, ExtFmt- EETLPPrefix- EmergencyPowerReduction Not Supported, EmergencyPowerReductionInit- FRS- TPHComp- ExtTPHComp- AtomicOpsCap: 32bit- 64bit- 128bitCAS- DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- LTR- OBFF Disabled, AtomicOpsCtl: ReqEn- LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete- EqualizationPhase1- EqualizationPhase2- EqualizationPhase3- LinkEqualizationRequest- Retimer- 2Retimers- CrosslinkRes: unsupported Capabilities: [b0] MSI-X: Enable- Count=4 Masked- Vector table: BAR=4 offset=00000000 PBA: BAR=4 offset=00000800 Capabilities: [d0] Vital Product Data Not readable Capabilities: [100 v2] Advanced Error Reporting UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol- CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr+ CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr+ AERCap: First Error Pointer: 00, ECRCGenCap+ ECRCGenEn- ECRCChkCap+ ECRCChkEn- MultHdrRecCap- MultHdrRecEn- TLPPfxPres- HdrLogCap- HeaderLog: 00000000 00000000 00000000 00000000 Capabilities: [160 v1] Device Serial Number 00-00-00-00-00-00-00-00 Capabilities: [170 v1] Latency Tolerance Reporting Max snoop latency: 0ns Max no snoop latency: 0ns Capabilities: [178 v1] L1 PM Substates L1SubCap: PCI-PM_L1.2+ PCI-PM_L1.1+ ASPM_L1.2+ ASPM_L1.1+ L1_PM_Substates+ PortCommonModeRestoreTime=150us PortTPowerOnTime=150us L1SubCtl1: PCI-PM_L1.2- PCI-PM_L1.1- ASPM_L1.2- ASPM_L1.1- T_CommonMode=0us LTR1.2_Threshold=0ns L1SubCtl2: T_PwrOn=10us 02:00.2 0700: 10ec:816b (rev 0e) [...same...] Signed-off-by: Tobias Diedrich <tobiasdiedrich@gmail.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200914173628.GA22508@yamamaya.is-a-geek.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 3c5a87be170aba8ac40982182f812dcff6ed1ad1 upstream.

These serial ports are exposed by the OOB-management-engine on
RealManage-enabled network cards (e.g. AMD DASH enabled systems using
Realtek cards).

Because these have 3 BARs, they fail the "num_iomem <= 1" check in
serial_pci_guess_board.

I've manually checked the two IOMEM regions and BAR 2 doesn't seem to
respond to reads, but BAR 4 seems to be an MMIO version of the IO ports
(untested).

With this change, the ports are detected:
0000:02:00.1: ttyS0 at I/O 0x2200 (irq = 82, base_baud = 115200) is a 16550A
0000:02:00.2: ttyS1 at I/O 0x2100 (irq = 55, base_baud = 115200) is a 16550A

lspci output:
02:00.1 0700: 10ec:816a (rev 0e) (prog-if 02 [16550])
        Subsystem: 17aa:5082
        Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort+ <TAbort- <MAbort- >SERR- <PERR- INTx-
        Interrupt: pin B routed to IRQ 82
        IOMMU group: 11
        Region 0: I/O ports at 2200 [size=256]
        Region 2: Memory at fd715000 (64-bit, non-prefetchable) [size=4K]
        Region 4: Memory at fd704000 (64-bit, non-prefetchable) [size=16K]
        Capabilities: [40] Power Management version 3
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
                Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit+
                Address: 0000000000000000  Data: 0000
        Capabilities: [70] Express (v2) Endpoint, MSI 01
                DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s unlimited, L1 <64us
                        ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset- SlotPowerLimit 0.000W
                DevCtl: CorrErr- NonFatalErr- FatalErr- UnsupReq-
                        RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop-
                        MaxPayload 128 bytes, MaxReadReq 512 bytes
                DevSta: CorrErr+ NonFatalErr- FatalErr- UnsupReq+ AuxPwr+ TransPend-
                LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s unlimited, L1 <64us
                        ClockPM+ Surprise- LLActRep- BwNot- ASPMOptComp+
                LnkCtl: ASPM L1 Enabled; RCB 64 bytes, Disabled- CommClk+
                        ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
                LnkSta: Speed 2.5GT/s (ok), Width x1 (ok)
                        TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
                DevCap2: Completion Timeout: Range ABCD, TimeoutDis+ NROPrPrP- LTR+
                         10BitTagComp- 10BitTagReq- OBFF Via message/WAKE#, ExtFmt- EETLPPrefix-
                         EmergencyPowerReduction Not Supported, EmergencyPowerReductionInit-
                         FRS- TPHComp- ExtTPHComp-
                         AtomicOpsCap: 32bit- 64bit- 128bitCAS-
                DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- LTR- OBFF Disabled,
                         AtomicOpsCtl: ReqEn-
                LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete- EqualizationPhase1-
                         EqualizationPhase2- EqualizationPhase3- LinkEqualizationRequest-
                         Retimer- 2Retimers- CrosslinkRes: unsupported
        Capabilities: [b0] MSI-X: Enable- Count=4 Masked-
                Vector table: BAR=4 offset=00000000
                PBA: BAR=4 offset=00000800
        Capabilities: [d0] Vital Product Data
                Not readable
        Capabilities: [100 v2] Advanced Error Reporting
                UESta:  DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
                UEMsk:  DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
                UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
                CESta:  RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr+
                CEMsk:  RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr+
                AERCap: First Error Pointer: 00, ECRCGenCap+ ECRCGenEn- ECRCChkCap+ ECRCChkEn-
                        MultHdrRecCap- MultHdrRecEn- TLPPfxPres- HdrLogCap-
                HeaderLog: 00000000 00000000 00000000 00000000
        Capabilities: [160 v1] Device Serial Number 00-00-00-00-00-00-00-00
        Capabilities: [170 v1] Latency Tolerance Reporting
                Max snoop latency: 0ns
                Max no snoop latency: 0ns
        Capabilities: [178 v1] L1 PM Substates
                L1SubCap: PCI-PM_L1.2+ PCI-PM_L1.1+ ASPM_L1.2+ ASPM_L1.1+ L1_PM_Substates+
                          PortCommonModeRestoreTime=150us PortTPowerOnTime=150us
                L1SubCtl1: PCI-PM_L1.2- PCI-PM_L1.1- ASPM_L1.2- ASPM_L1.1-
                           T_CommonMode=0us LTR1.2_Threshold=0ns
                L1SubCtl2: T_PwrOn=10us
02:00.2 0700: 10ec:816b (rev 0e)
[...same...]

Signed-off-by: Tobias Diedrich <tobiasdiedrich@gmail.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200914173628.GA22508@yamamaya.is-a-geek.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tty: serial: qcom_geni_serial: Drop __init from qcom_geni_console_setup 2020-09-09T17:12:20+00:00 John Stultz john.stultz@linaro.org 2020-08-11T02:50:44+00:00 8bc25dea70fe372be80b51dd4e8d0ec42e8f749c [ Upstream commit 975efc66d4e654207c17f939eb737ac591ac38fe ] When booting with heavily modularized config, the serial console may not be able to load until after init when modules that satisfy needed dependencies have time to load. Unfortunately, as qcom_geni_console_setup is marked as __init, the function may have been freed before we get to run it, causing boot time crashes such as: [ 6.469057] Unable to handle kernel paging request at virtual address ffffffe645d4e6cc [ 6.481623] Mem abort info: [ 6.484466] ESR = 0x86000007 [ 6.487557] EC = 0x21: IABT (current EL), IL = 32 bits [ 6.492929] SET = 0, FnV = 0g [ 6.496016] EA = 0, S1PTW = 0 [ 6.499202] swapper pgtable: 4k pages, 39-bit VAs, pgdp=000000008151e000 [ 6.501286] ufshcd-qcom 1d84000.ufshc: ufshcd_print_pwr_info:[RX, TX]: gear=[3, 3], lane[2, 2], pwr[FAST MODE, FAST MODE], rate = 2 [ 6.505977] [ffffffe645d4e6cc] pgd=000000017df9f003, p4d=000000017df9f003, pud=000000017df9f003, pmd=000000017df9c003, pte=0000000000000000 [ 6.505990] Internal error: Oops: 86000007 [#1] PREEMPT SMP [ 6.505995] Modules linked in: zl10353 zl10039 zl10036 zd1301_demod xc5000 xc4000 ves1x93 ves1820 tuner_xc2028 tuner_simple tuner_types tua9001 tua6100 1 [ 6.506152] isl6405 [ 6.518104] ufshcd-qcom 1d84000.ufshc: ufshcd_find_max_sup_active_icc_level: Regulator capability was not set, actvIccLevel=0 [ 6.530549] horus3a helene fc2580 fc0013 fc0012 fc0011 ec100 e4000 dvb_pll ds3000 drxk drxd drx39xyj dib9000 dib8000 dib7000p dib7000m dib3000mc dibx003 [ 6.624271] CPU: 7 PID: 148 Comm: kworker/7:2 Tainted: G W 5.8.0-mainline-12021-g6defd37ba1cd #3455 [ 6.624273] Hardware name: Thundercomm Dragonboard 845c (DT) [ 6.624290] Workqueue: events deferred_probe_work_func [ 6.624296] pstate: 40c00005 (nZcv daif +PAN +UAO BTYPE=--) [ 6.624307] pc : qcom_geni_console_setup+0x0/0x110 [ 6.624316] lr : try_enable_new_console+0xa0/0x140 [ 6.624318] sp : ffffffc010843a30 [ 6.624320] x29: ffffffc010843a30 x28: ffffffe645c3e7d0 [ 6.624325] x27: ffffff80f8022180 x26: ffffffc010843b28 [ 6.637937] x25: 0000000000000000 x24: ffffffe6462a2000 [ 6.637941] x23: ffffffe646398000 x22: 0000000000000000 [ 6.637945] x21: 0000000000000000 x20: ffffffe6462a5ce8 [ 6.637952] x19: ffffffe646398e38 x18: ffffffffffffffff [ 6.680296] x17: 0000000000000000 x16: ffffffe64492b900 [ 6.680300] x15: ffffffe6461e9d08 x14: 69202930203d2064 [ 6.680305] x13: 7561625f65736162 x12: 202c363331203d20 [ 6.696434] x11: 0000000000000030 x10: 0101010101010101 [ 6.696438] x9 : 4d4d20746120304d x8 : 7f7f7f7f7f7f7f7f [ 6.707249] x7 : feff4c524c787373 x6 : 0000000000008080 [ 6.707253] x5 : 0000000000000000 x4 : 8080000000000000 [ 6.707257] x3 : 0000000000000000 x2 : ffffffe645d4e6cc [ 6.744223] qcom_geni_serial 898000.serial: dev_pm_opp_set_rate: failed to find OPP for freq 102400000 (-34) [ 6.744966] x1 : fffffffefe74e174 x0 : ffffffe6462a5ce8 [ 6.753580] qcom_geni_serial 898000.serial: dev_pm_opp_set_rate: failed to find OPP for freq 102400000 (-34) [ 6.761634] Call trace: [ 6.761639] qcom_geni_console_setup+0x0/0x110 [ 6.761645] register_console+0x29c/0x2f8 [ 6.767981] Bluetooth: hci0: Frame reassembly failed (-84) [ 6.775252] uart_add_one_port+0x438/0x500 [ 6.775258] qcom_geni_serial_probe+0x2c4/0x4a8 [ 6.775266] platform_drv_probe+0x58/0xa8 [ 6.855359] really_probe+0xec/0x398 [ 6.855362] driver_probe_device+0x5c/0xb8 [ 6.855367] __device_attach_driver+0x98/0xb8 [ 7.184945] bus_for_each_drv+0x74/0xd8 [ 7.188825] __device_attach+0xec/0x148 [ 7.192705] device_initial_probe+0x24/0x30 [ 7.196937] bus_probe_device+0x9c/0xa8 [ 7.200816] deferred_probe_work_func+0x7c/0xb8 [ 7.205398] process_one_work+0x20c/0x4b0 [ 7.209456] worker_thread+0x48/0x460 [ 7.213157] kthread+0x14c/0x158 [ 7.216432] ret_from_fork+0x10/0x18 [ 7.220049] Code: bad PC value [ 7.223139] ---[ end trace 73f3b21e251d5a70 ]--- Thus this patch removes the __init avoiding crash in such configs. Cc: Andy Gross <agross@kernel.org> Cc: Jiri Slaby <jirislaby@kernel.org> Cc: Saravana Kannan <saravanak@google.com> Cc: Todd Kjos <tkjos@google.com> Cc: Amit Pundir <amit.pundir@linaro.org> Cc: linux-arm-msm@vger.kernel.org Cc: linux-serial@vger.kernel.org Suggested-by: Saravana Kannan <saravanak@google.com> Signed-off-by: John Stultz <john.stultz@linaro.org> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Link: https://lore.kernel.org/r/20200811025044.70626-1-john.stultz@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit 975efc66d4e654207c17f939eb737ac591ac38fe ]

When booting with heavily modularized config, the serial console
may not be able to load until after init when modules that
satisfy needed dependencies have time to load.

Unfortunately, as qcom_geni_console_setup is marked as __init,
the function may have been freed before we get to run it,
causing boot time crashes such as:

[    6.469057] Unable to handle kernel paging request at virtual address ffffffe645d4e6cc
[    6.481623] Mem abort info:
[    6.484466]   ESR = 0x86000007
[    6.487557]   EC = 0x21: IABT (current EL), IL = 32 bits
[    6.492929]   SET = 0, FnV = 0g
[    6.496016]   EA = 0, S1PTW = 0
[    6.499202] swapper pgtable: 4k pages, 39-bit VAs, pgdp=000000008151e000
[    6.501286] ufshcd-qcom 1d84000.ufshc: ufshcd_print_pwr_info:[RX, TX]: gear=[3, 3], lane[2, 2], pwr[FAST MODE, FAST MODE], rate = 2
[    6.505977] [ffffffe645d4e6cc] pgd=000000017df9f003, p4d=000000017df9f003, pud=000000017df9f003, pmd=000000017df9c003, pte=0000000000000000
[    6.505990] Internal error: Oops: 86000007 [#1] PREEMPT SMP
[    6.505995] Modules linked in: zl10353 zl10039 zl10036 zd1301_demod xc5000 xc4000 ves1x93 ves1820 tuner_xc2028 tuner_simple tuner_types tua9001 tua6100 1
[    6.506152]  isl6405
[    6.518104] ufshcd-qcom 1d84000.ufshc: ufshcd_find_max_sup_active_icc_level: Regulator capability was not set, actvIccLevel=0
[    6.530549]  horus3a helene fc2580 fc0013 fc0012 fc0011 ec100 e4000 dvb_pll ds3000 drxk drxd drx39xyj dib9000 dib8000 dib7000p dib7000m dib3000mc dibx003
[    6.624271] CPU: 7 PID: 148 Comm: kworker/7:2 Tainted: G        W       5.8.0-mainline-12021-g6defd37ba1cd #3455
[    6.624273] Hardware name: Thundercomm Dragonboard 845c (DT)
[    6.624290] Workqueue: events deferred_probe_work_func
[    6.624296] pstate: 40c00005 (nZcv daif +PAN +UAO BTYPE=--)
[    6.624307] pc : qcom_geni_console_setup+0x0/0x110
[    6.624316] lr : try_enable_new_console+0xa0/0x140
[    6.624318] sp : ffffffc010843a30
[    6.624320] x29: ffffffc010843a30 x28: ffffffe645c3e7d0
[    6.624325] x27: ffffff80f8022180 x26: ffffffc010843b28
[    6.637937] x25: 0000000000000000 x24: ffffffe6462a2000
[    6.637941] x23: ffffffe646398000 x22: 0000000000000000
[    6.637945] x21: 0000000000000000 x20: ffffffe6462a5ce8
[    6.637952] x19: ffffffe646398e38 x18: ffffffffffffffff
[    6.680296] x17: 0000000000000000 x16: ffffffe64492b900
[    6.680300] x15: ffffffe6461e9d08 x14: 69202930203d2064
[    6.680305] x13: 7561625f65736162 x12: 202c363331203d20
[    6.696434] x11: 0000000000000030 x10: 0101010101010101
[    6.696438] x9 : 4d4d20746120304d x8 : 7f7f7f7f7f7f7f7f
[    6.707249] x7 : feff4c524c787373 x6 : 0000000000008080
[    6.707253] x5 : 0000000000000000 x4 : 8080000000000000
[    6.707257] x3 : 0000000000000000 x2 : ffffffe645d4e6cc
[    6.744223] qcom_geni_serial 898000.serial: dev_pm_opp_set_rate: failed to find OPP for freq 102400000 (-34)
[    6.744966] x1 : fffffffefe74e174 x0 : ffffffe6462a5ce8
[    6.753580] qcom_geni_serial 898000.serial: dev_pm_opp_set_rate: failed to find OPP for freq 102400000 (-34)
[    6.761634] Call trace:
[    6.761639]  qcom_geni_console_setup+0x0/0x110
[    6.761645]  register_console+0x29c/0x2f8
[    6.767981] Bluetooth: hci0: Frame reassembly failed (-84)
[    6.775252]  uart_add_one_port+0x438/0x500
[    6.775258]  qcom_geni_serial_probe+0x2c4/0x4a8
[    6.775266]  platform_drv_probe+0x58/0xa8
[    6.855359]  really_probe+0xec/0x398
[    6.855362]  driver_probe_device+0x5c/0xb8
[    6.855367]  __device_attach_driver+0x98/0xb8
[    7.184945]  bus_for_each_drv+0x74/0xd8
[    7.188825]  __device_attach+0xec/0x148
[    7.192705]  device_initial_probe+0x24/0x30
[    7.196937]  bus_probe_device+0x9c/0xa8
[    7.200816]  deferred_probe_work_func+0x7c/0xb8
[    7.205398]  process_one_work+0x20c/0x4b0
[    7.209456]  worker_thread+0x48/0x460
[    7.213157]  kthread+0x14c/0x158
[    7.216432]  ret_from_fork+0x10/0x18
[    7.220049] Code: bad PC value
[    7.223139] ---[ end trace 73f3b21e251d5a70 ]---

Thus this patch removes the __init avoiding crash in such
configs.

Cc: Andy Gross <agross@kernel.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: Saravana Kannan <saravanak@google.com>
Cc: Todd Kjos <tkjos@google.com>
Cc: Amit Pundir <amit.pundir@linaro.org>
Cc: linux-arm-msm@vger.kernel.org
Cc: linux-serial@vger.kernel.org
Suggested-by: Saravana Kannan <saravanak@google.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200811025044.70626-1-john.stultz@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
serial: 8250: change lock order in serial8250_do_startup() 2020-09-03T09:27:04+00:00 Sergey Senozhatsky sergey.senozhatsky@gmail.com 2020-08-17T02:26:46+00:00 2e76a3a1667c41686501de38831aad12ab797d1f commit 205d300aea75623e1ae4aa43e0d265ab9cf195fd upstream. We have a number of "uart.port->desc.lock vs desc.lock->uart.port" lockdep reports coming from 8250 driver; this causes a bit of trouble to people, so let's fix it. The problem is reverse lock order in two different call paths: chain #1: serial8250_do_startup() spin_lock_irqsave(&port->lock); disable_irq_nosync(port->irq); raw_spin_lock_irqsave(&desc->lock) chain #2: __report_bad_irq() raw_spin_lock_irqsave(&desc->lock) for_each_action_of_desc() printk() spin_lock_irqsave(&port->lock); Fix this by changing the order of locks in serial8250_do_startup(): do disable_irq_nosync() first, which grabs desc->lock, and grab uart->port after that, so that chain #1 and chain #2 have same lock order. Full lockdep splat: ====================================================== WARNING: possible circular locking dependency detected 5.4.39 #55 Not tainted ====================================================== swapper/0/0 is trying to acquire lock: ffffffffab65b6c0 (console_owner){-...}, at: console_lock_spinning_enable+0x31/0x57 but task is already holding lock: ffff88810a8e34c0 (&irq_desc_lock_class){-.-.}, at: __report_bad_irq+0x5b/0xba which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> #2 (&irq_desc_lock_class){-.-.}: _raw_spin_lock_irqsave+0x61/0x8d __irq_get_desc_lock+0x65/0x89 __disable_irq_nosync+0x3b/0x93 serial8250_do_startup+0x451/0x75c uart_startup+0x1b4/0x2ff uart_port_activate+0x73/0xa0 tty_port_open+0xae/0x10a uart_open+0x1b/0x26 tty_open+0x24d/0x3a0 chrdev_open+0xd5/0x1cc do_dentry_open+0x299/0x3c8 path_openat+0x434/0x1100 do_filp_open+0x9b/0x10a do_sys_open+0x15f/0x3d7 kernel_init_freeable+0x157/0x1dd kernel_init+0xe/0x105 ret_from_fork+0x27/0x50 -> #1 (&port_lock_key){-.-.}: _raw_spin_lock_irqsave+0x61/0x8d serial8250_console_write+0xa7/0x2a0 console_unlock+0x3b7/0x528 vprintk_emit+0x111/0x17f printk+0x59/0x73 register_console+0x336/0x3a4 uart_add_one_port+0x51b/0x5be serial8250_register_8250_port+0x454/0x55e dw8250_probe+0x4dc/0x5b9 platform_drv_probe+0x67/0x8b really_probe+0x14a/0x422 driver_probe_device+0x66/0x130 device_driver_attach+0x42/0x5b __driver_attach+0xca/0x139 bus_for_each_dev+0x97/0xc9 bus_add_driver+0x12b/0x228 driver_register+0x64/0xed do_one_initcall+0x20c/0x4a6 do_initcall_level+0xb5/0xc5 do_basic_setup+0x4c/0x58 kernel_init_freeable+0x13f/0x1dd kernel_init+0xe/0x105 ret_from_fork+0x27/0x50 -> #0 (console_owner){-...}: __lock_acquire+0x118d/0x2714 lock_acquire+0x203/0x258 console_lock_spinning_enable+0x51/0x57 console_unlock+0x25d/0x528 vprintk_emit+0x111/0x17f printk+0x59/0x73 __report_bad_irq+0xa3/0xba note_interrupt+0x19a/0x1d6 handle_irq_event_percpu+0x57/0x79 handle_irq_event+0x36/0x55 handle_fasteoi_irq+0xc2/0x18a do_IRQ+0xb3/0x157 ret_from_intr+0x0/0x1d cpuidle_enter_state+0x12f/0x1fd cpuidle_enter+0x2e/0x3d do_idle+0x1ce/0x2ce cpu_startup_entry+0x1d/0x1f start_kernel+0x406/0x46a secondary_startup_64+0xa4/0xb0 other info that might help us debug this: Chain exists of: console_owner --> &port_lock_key --> &irq_desc_lock_class Possible unsafe locking scenario: CPU0 CPU1 ---- ---- lock(&irq_desc_lock_class); lock(&port_lock_key); lock(&irq_desc_lock_class); lock(console_owner); *** DEADLOCK *** 2 locks held by swapper/0/0: #0: ffff88810a8e34c0 (&irq_desc_lock_class){-.-.}, at: __report_bad_irq+0x5b/0xba #1: ffffffffab65b5c0 (console_lock){+.+.}, at: console_trylock_spinning+0x20/0x181 stack backtrace: CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.4.39 #55 Hardware name: XXXXXX Call Trace: <IRQ> dump_stack+0xbf/0x133 ? print_circular_bug+0xd6/0xe9 check_noncircular+0x1b9/0x1c3 __lock_acquire+0x118d/0x2714 lock_acquire+0x203/0x258 ? console_lock_spinning_enable+0x31/0x57 console_lock_spinning_enable+0x51/0x57 ? console_lock_spinning_enable+0x31/0x57 console_unlock+0x25d/0x528 ? console_trylock+0x18/0x4e vprintk_emit+0x111/0x17f ? lock_acquire+0x203/0x258 printk+0x59/0x73 __report_bad_irq+0xa3/0xba note_interrupt+0x19a/0x1d6 handle_irq_event_percpu+0x57/0x79 handle_irq_event+0x36/0x55 handle_fasteoi_irq+0xc2/0x18a do_IRQ+0xb3/0x157 common_interrupt+0xf/0xf </IRQ> Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com> Fixes: 768aec0b5bcc ("serial: 8250: fix shared interrupts issues with SMP and RT kernels") Reported-by: Guenter Roeck <linux@roeck-us.net> Reported-by: Raul Rangel <rrangel@google.com> BugLink: https://bugs.chromium.org/p/chromium/issues/detail?id=1114800 Link: https://lore.kernel.org/lkml/CAHQZ30BnfX+gxjPm1DUd5psOTqbyDh4EJE=2=VAMW_VDafctkA@mail.gmail.com/T/#u Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Tested-by: Guenter Roeck <linux@roeck-us.net> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200817022646.1484638-1-sergey.senozhatsky@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 205d300aea75623e1ae4aa43e0d265ab9cf195fd upstream.

We have a number of "uart.port->desc.lock vs desc.lock->uart.port"
lockdep reports coming from 8250 driver; this causes a bit of trouble
to people, so let's fix it.

The problem is reverse lock order in two different call paths:

chain #1:

 serial8250_do_startup()
  spin_lock_irqsave(&port->lock);
   disable_irq_nosync(port->irq);
    raw_spin_lock_irqsave(&desc->lock)

chain #2:

  __report_bad_irq()
   raw_spin_lock_irqsave(&desc->lock)
    for_each_action_of_desc()
     printk()
      spin_lock_irqsave(&port->lock);

Fix this by changing the order of locks in serial8250_do_startup():
 do disable_irq_nosync() first, which grabs desc->lock, and grab
 uart->port after that, so that chain #1 and chain #2 have same lock
 order.

Full lockdep splat:

 ======================================================
 WARNING: possible circular locking dependency detected
 5.4.39 #55 Not tainted
 ======================================================

 swapper/0/0 is trying to acquire lock:
 ffffffffab65b6c0 (console_owner){-...}, at: console_lock_spinning_enable+0x31/0x57

 but task is already holding lock:
 ffff88810a8e34c0 (&irq_desc_lock_class){-.-.}, at: __report_bad_irq+0x5b/0xba

 which lock already depends on the new lock.

 the existing dependency chain (in reverse order) is:

 -> #2 (&irq_desc_lock_class){-.-.}:
        _raw_spin_lock_irqsave+0x61/0x8d
        __irq_get_desc_lock+0x65/0x89
        __disable_irq_nosync+0x3b/0x93
        serial8250_do_startup+0x451/0x75c
        uart_startup+0x1b4/0x2ff
        uart_port_activate+0x73/0xa0
        tty_port_open+0xae/0x10a
        uart_open+0x1b/0x26
        tty_open+0x24d/0x3a0
        chrdev_open+0xd5/0x1cc
        do_dentry_open+0x299/0x3c8
        path_openat+0x434/0x1100
        do_filp_open+0x9b/0x10a
        do_sys_open+0x15f/0x3d7
        kernel_init_freeable+0x157/0x1dd
        kernel_init+0xe/0x105
        ret_from_fork+0x27/0x50

 -> #1 (&port_lock_key){-.-.}:
        _raw_spin_lock_irqsave+0x61/0x8d
        serial8250_console_write+0xa7/0x2a0
        console_unlock+0x3b7/0x528
        vprintk_emit+0x111/0x17f
        printk+0x59/0x73
        register_console+0x336/0x3a4
        uart_add_one_port+0x51b/0x5be
        serial8250_register_8250_port+0x454/0x55e
        dw8250_probe+0x4dc/0x5b9
        platform_drv_probe+0x67/0x8b
        really_probe+0x14a/0x422
        driver_probe_device+0x66/0x130
        device_driver_attach+0x42/0x5b
        __driver_attach+0xca/0x139
        bus_for_each_dev+0x97/0xc9
        bus_add_driver+0x12b/0x228
        driver_register+0x64/0xed
        do_one_initcall+0x20c/0x4a6
        do_initcall_level+0xb5/0xc5
        do_basic_setup+0x4c/0x58
        kernel_init_freeable+0x13f/0x1dd
        kernel_init+0xe/0x105
        ret_from_fork+0x27/0x50

 -> #0 (console_owner){-...}:
        __lock_acquire+0x118d/0x2714
        lock_acquire+0x203/0x258
        console_lock_spinning_enable+0x51/0x57
        console_unlock+0x25d/0x528
        vprintk_emit+0x111/0x17f
        printk+0x59/0x73
        __report_bad_irq+0xa3/0xba
        note_interrupt+0x19a/0x1d6
        handle_irq_event_percpu+0x57/0x79
        handle_irq_event+0x36/0x55
        handle_fasteoi_irq+0xc2/0x18a
        do_IRQ+0xb3/0x157
        ret_from_intr+0x0/0x1d
        cpuidle_enter_state+0x12f/0x1fd
        cpuidle_enter+0x2e/0x3d
        do_idle+0x1ce/0x2ce
        cpu_startup_entry+0x1d/0x1f
        start_kernel+0x406/0x46a
        secondary_startup_64+0xa4/0xb0

 other info that might help us debug this:

 Chain exists of:
   console_owner --> &port_lock_key --> &irq_desc_lock_class

  Possible unsafe locking scenario:

        CPU0                    CPU1
        ----                    ----
   lock(&irq_desc_lock_class);
                                lock(&port_lock_key);
                                lock(&irq_desc_lock_class);
   lock(console_owner);

  *** DEADLOCK ***

 2 locks held by swapper/0/0:
  #0: ffff88810a8e34c0 (&irq_desc_lock_class){-.-.}, at: __report_bad_irq+0x5b/0xba
  #1: ffffffffab65b5c0 (console_lock){+.+.}, at: console_trylock_spinning+0x20/0x181

 stack backtrace:
 CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.4.39 #55
 Hardware name: XXXXXX
 Call Trace:
  <IRQ>
  dump_stack+0xbf/0x133
  ? print_circular_bug+0xd6/0xe9
  check_noncircular+0x1b9/0x1c3
  __lock_acquire+0x118d/0x2714
  lock_acquire+0x203/0x258
  ? console_lock_spinning_enable+0x31/0x57
  console_lock_spinning_enable+0x51/0x57
  ? console_lock_spinning_enable+0x31/0x57
  console_unlock+0x25d/0x528
  ? console_trylock+0x18/0x4e
  vprintk_emit+0x111/0x17f
  ? lock_acquire+0x203/0x258
  printk+0x59/0x73
  __report_bad_irq+0xa3/0xba
  note_interrupt+0x19a/0x1d6
  handle_irq_event_percpu+0x57/0x79
  handle_irq_event+0x36/0x55
  handle_fasteoi_irq+0xc2/0x18a
  do_IRQ+0xb3/0x157
  common_interrupt+0xf/0xf
  </IRQ>

Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Fixes: 768aec0b5bcc ("serial: 8250: fix shared interrupts issues with SMP and RT kernels")
Reported-by: Guenter Roeck <linux@roeck-us.net>
Reported-by: Raul Rangel <rrangel@google.com>
BugLink: https://bugs.chromium.org/p/chromium/issues/detail?id=1114800
Link: https://lore.kernel.org/lkml/CAHQZ30BnfX+gxjPm1DUd5psOTqbyDh4EJE=2=VAMW_VDafctkA@mail.gmail.com/T/#u
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200817022646.1484638-1-sergey.senozhatsky@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
serial: 8250_exar: Fix number of ports for Commtech PCIe cards 2020-09-03T09:27:03+00:00 Valmer Huhn valmer.huhn@concurrent-rt.com 2020-08-13T16:52:55+00:00 f53ebc7c292299b2026b048c320018248bb93ed9 commit c6b9e95dde7b54e6a53c47241201ab5a4035c320 upstream. The following in 8250_exar.c line 589 is used to determine the number of ports for each Exar board: nr_ports = board->num_ports ? board->num_ports : pcidev->device & 0x0f; If the number of ports a card has is not explicitly specified, it defaults to the rightmost 4 bits of the PCI device ID. This is prone to error since not all PCI device IDs contain a number which corresponds to the number of ports that card provides. This particular case involves COMMTECH_4222PCIE, COMMTECH_4224PCIE and COMMTECH_4228PCIE cards with device IDs 0x0022, 0x0020 and 0x0021. Currently the multiport cards receive 2, 0 and 1 port instead of 2, 4 and 8 ports respectively. To fix this, each Commtech Fastcom PCIe card is given a struct where the number of ports is explicitly specified. This ensures 'board->num_ports' is used instead of the default 'pcidev->device & 0x0f'. Fixes: d0aeaa83f0b0 ("serial: exar: split out the exar code from 8250_pci") Signed-off-by: Valmer Huhn <valmer.huhn@concurrent-rt.com> Tested-by: Valmer Huhn <valmer.huhn@concurrent-rt.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200813165255.GC345440@icarus.concurrent-rt.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit c6b9e95dde7b54e6a53c47241201ab5a4035c320 upstream.

The following in 8250_exar.c line 589 is used to determine the number
of ports for each Exar board:

nr_ports = board->num_ports ? board->num_ports : pcidev->device & 0x0f;

If the number of ports a card has is not explicitly specified, it defaults
to the rightmost 4 bits of the PCI device ID. This is prone to error since
not all PCI device IDs contain a number which corresponds to the number of
ports that card provides.

This particular case involves COMMTECH_4222PCIE, COMMTECH_4224PCIE and
COMMTECH_4228PCIE cards with device IDs 0x0022, 0x0020 and 0x0021.
Currently the multiport cards receive 2, 0 and 1 port instead of 2, 4 and
8 ports respectively.

To fix this, each Commtech Fastcom PCIe card is given a struct where the
number of ports is explicitly specified. This ensures 'board->num_ports'
is used instead of the default 'pcidev->device & 0x0f'.

Fixes: d0aeaa83f0b0 ("serial: exar: split out the exar code from 8250_pci")
Signed-off-by: Valmer Huhn <valmer.huhn@concurrent-rt.com>
Tested-by: Valmer Huhn <valmer.huhn@concurrent-rt.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200813165255.GC345440@icarus.concurrent-rt.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>