linux-stable.git/drivers/tty/serial, branch v4.9.99

serial: imx: ensure UCR3 and UFCR are setup correctly

2018-05-09T07:50:19+00:00

commit 6df765dca378bddf994cfd2044acafa501bd800f upstream.

Commit e61c38d85b73 ("serial: imx: setup DCEDTE early and ensure DCD and
RI irqs to be off") has a flaw: While UCR3 and UFCR were modified using
read-modify-write before it switched to write register values
independent of the previous state. That's a good idea in principle (and
that's why I did it) but needs more care.

This patch reinstates read-modify-write for UFCR and for UCR3 ensures
that RXDMUXSEL and ADNIMP are set for post imx1.

Fixes: e61c38d85b73 ("serial: imx: setup DCEDTE early and ensure DCD and RI irqs to be off")
Signed-off-by: Uwe Kleine-König 
Acked-by: Mika Penttilä 
Tested-by: Mika Penttilä 
Acked-by: Steve Twiss 
Tested-by: Steve Twiss 
Cc: Chris Ruehl 
Signed-off-by: Greg Kroah-Hartman

earlycon: Use a pointer table to fix __earlycon_table stride

2018-05-01T22:13:09+00:00

commit dd709e72cb934eefd44de8d9969097173fbf45dc upstream.

Commit 99492c39f39f ("earlycon: Fix __earlycon_table stride") tried to fix
__earlycon_table stride by forcing the earlycon_id struct alignment to 32
and asking the linker to 32-byte align the __earlycon_table symbol.  This
fix was based on commit 07fca0e57fca92 ("tracing: Properly align linker
defined symbols") which tried a similar fix for the tracing subsystem.

However, this fix doesn't quite work because there is no guarantee that
gcc will place structures packed into an array format.  In fact, gcc 4.9
chooses to 64-byte align these structs by inserting additional padding
between the entries because it has no clue that they are supposed to be in
an array.  If we are unlucky, the linker will assign symbol
"__earlycon_table" to a 32-byte aligned address which does not correspond
to the 64-byte aligned contents of section "__earlycon_table".

To address this same problem, the fix to the tracing system was
subsequently re-implemented using a more robust table of pointers approach
by commits:
 3d56e331b653 ("tracing: Replace syscall_meta_data struct array with pointer array")
 654986462939 ("tracepoints: Fix section alignment using pointer array")
 e4a9ea5ee7c8 ("tracing: Replace trace_event struct array with pointer array")

Let's use this same "array of pointers to structs" approach for
EARLYCON_TABLE.

Fixes: 99492c39f39f ("earlycon: Fix __earlycon_table stride")
Signed-off-by: Daniel Kurtz 
Suggested-by: Aaron Durbin 
Reviewed-by: Rob Herring 
Tested-by: Guenter Roeck 
Reviewed-by: Guenter Roeck 
Cc: stable 
Signed-off-by: Greg Kroah-Hartman

Fix serial console on SNI RM400 machines

2018-04-13T17:48:18+00:00

[ Upstream commit e279e6d98e0cf2c2fe008b3c29042b92f0e17b1d ]

sccnxp driver doesn't get the correct uart clock rate, if CONFIG_HAVE_CLOCK
is disabled. Correct usage of clk API to make it work with/without it.

Fixes: 90efa75f7ab0 (serial: sccnxp: Using CLK API for getting UART clock)

Suggested-by: Russell King - ARM Linux 
Signed-off-by: Thomas Bogendoerfer 
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman

serial: sh-sci: Fix race condition causing garbage during shutdown

2018-04-13T17:48:00+00:00

[ Upstream commit 1cf4a7efdc71cab84c42cfea7200608711ea954f ]

If DMA is enabled and used, a burst of old data may be seen on the
serial console during "poweroff" or "reboot".  uart_flush_buffer()
clears the circular buffer, but sci_port.tx_dma_len is not reset.
This leads to a circular buffer overflow, dumping (UART_XMIT_SIZE -
sci_port.tx_dma_len) bytes.

To fix this, add a .flush_buffer() callback that resets
sci_port.tx_dma_len.

Inspired by commit 31ca2c63fdc0aee7 ("tty/serial: atmel: fix race
condition (TX+DMA)").

Signed-off-by: Geert Uytterhoeven 
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman

serial: 8250: omap: Disable DMA for console UART

2018-04-13T17:48:00+00:00

[ Upstream commit 84b40e3b57eef1417479c00490dd4c9f6e5ffdbc ]

Kernel always writes log messages to console via
serial8250_console_write()->serial8250_console_putchar() which directly
accesses UART_TX register _without_ using DMA.

But, if other processes like systemd using same UART port, then these
writes are handled by a different code flow using 8250_omap driver where
there is provision to use DMA.

It seems that it is possible that both DMA and CPU might simultaneously
put data to UART FIFO and lead to potential loss of data due to FIFO
overflow and weird data corruption. This happens when both kernel
console and userspace tries to write simultaneously to the same UART
port. Therefore, disable DMA on kernel console port to avoid potential
race between CPU and DMA.

Signed-off-by: Vignesh R 
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman

serial: 8250_dw: Disable clock on error

2018-03-24T10:00:23+00:00

[ Upstream commit 8af016aa5a27c6a2505460eb4d83f1e70c38dc43 ]

If there is no clock rate for uartclk defined, disable the previously
enabled clock again.

Found by Linux Driver Verification project (linuxtesting.org).

Fixes: 23f5b3fdd04e serial: 8250_dw: only get the clock rate in one place
Signed-off-by: Stefan Potyra 
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman

serial: imx: setup DCEDTE early and ensure DCD and RI irqs to be off

2018-03-22T08:17:49+00:00

[ Upstream commit e61c38d85b7392e033ee03bca46f1d6006156175 ]

If the UART is operated in DTE mode and UCR3_DCD or UCR3_RI are 1 (which
is the reset default) and the opposite side pulls the respective line to
its active level the irq triggers after it is requested in .probe.

These irqs were already disabled in .startup but this might be too late.

Also setup of the UFCR_DCEDTE bit (currently done in .set_termios) is
done very late which is critical as it also controls direction of some
pins.

So setup UFCR_DCEDTE earlier (in .probe) and also disable the broken
irqs in DTE mode there before requesting irqs.

Acked-by: Lucas Stach 
Signed-off-by: Uwe Kleine-König 
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman

tty: amba-pl011: Fix spurious TX interrupts

2018-03-22T08:17:49+00:00

[ Upstream commit 7d05587c9e0e4611650bb403812e2d492c178a9f ]

On SMP systems, we see a lot of spurious TX interrupts when a
program generates a steady stream of output to the pl011 UART.

The problem can be easily seen when one CPU generates the output
while another CPU handles the pl011 interrupts, and the rate of
output is low enough not to fill the TX FIFO. The problem seems
to be:

    -- CPU a --                        -- CPU b --
   (take port lock)
   pl011_start_tx
      pl011_start_tx_pio
         enable TXIM in REG_IMSC   ->  causes uart tx intr (pl011_int)
         pl011_tx_chars                pl011_int
            ...tx chars, all done...       (wait for port lock)
            pl011_stop_tx                   .
               disable TXIM                 .
    (release port lock)            ->      (take port lock)
                                           check for TXIM, not enabled
                                           (release port lock)
                                           return IRQ_NONE

Enabling the TXIM in pl011_start_tx_pio() causes the interrupt
to be generated and delivered to CPU b, even though pl011_tx_chars()
is able to complete the TX and then disable the tx interrupt.

Fix this by enabling TXIM only after pl011_tx_chars, if it is needed.
pl011_tx_chars will return a boolean indicating whether the TX
interrupts have to be enabled.

Debugged-by: Vijaya Kumar 
Signed-off-by: Jayachandran C 
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman

earlycon: add reg-offset to physical address before mapping

2018-03-18T10:18:56+00:00

commit 1f66dd36bb18437397ea0d7882c52f7e3c476e15 upstream.

It will get the wrong virtual address because port->mapbase is not added
the correct reg-offset yet. We have to update it before earlycon_map()
is called

Signed-off-by: Greentime Hu 
Acked-by: Arnd Bergmann 
Cc: Peter Hurley 
Cc: stable@vger.kernel.org
Fixes: 088da2a17619 ("of: earlycon: Initialize port fields from DT properties")
Acked-by: Rob Herring 
Signed-off-by: Greg Kroah-Hartman

serial: core: mark port as initialized in autoconfig

2018-03-18T10:18:56+00:00

commit 714569064adee3c114a2a6490735b94abe269068 upstream.

This is a followup on 44117a1d1732 ("serial: core: mark port as
initialized after successful IRQ change").
Nikola has been using autoconfig via setserial and reported a crash
similar to what I fixed in the earlier mentioned commit. Here I do the
same fixup for the autoconfig. I wasn't sure that this is the right
approach. Nikola confirmed that it fixes his crash.

Fixes: b3b576461864 ("tty: serial_core: convert uart_open to use tty_port_open")
Link: http://lkml.kernel.org/r/20180131072000.GD1853@localhost.localdomain
Reported-by: Nikola Ciprich 
Tested-by: Nikola Ciprich 
Cc: 
Signed-off-by: Sebastian Andrzej Siewior 
Tested-by: Nikola Ciprich 
Acked-by: Johan Hovold 
Signed-off-by: Greg Kroah-Hartman