linux-stable.git/drivers/tty/serial, branch v4.4.294

serial: pl011: Add ACPI SBSA UART match id

2021-12-08T07:44:08+00:00

commit ac442a077acf9a6bf1db4320ec0c3f303be092b3 upstream.

The document 'ACPI for Arm Components 1.0' defines the following
_HID mappings:
-'Prime cell UART (PL011)': ARMH0011
-'SBSA UART': ARMHB000

Use the sbsa-uart driver when a device is described with
the 'ARMHB000' _HID.

Note:
PL011 devices currently use the sbsa-uart driver instead of the
uart-pl011 driver. Indeed, PL011 devices are not bound to a clock
in ACPI. It is not possible to change their baudrate.

Cc: 
Signed-off-by: Pierre Gondois 
Link: https://lore.kernel.org/r/20211109172248.19061-1-Pierre.Gondois@arm.com
Signed-off-by: Greg Kroah-Hartman

tty: serial: msm_serial: Deactivate RX DMA for polling support

2021-12-08T07:44:08+00:00

commit 7492ffc90fa126afb67d4392d56cb4134780194a upstream.

The CONSOLE_POLLING mode is used for tools like k(g)db. In this kind of
setup, it is often sharing a serial device with the normal system console.
This is usually no problem because the polling helpers can consume input
values directly (when in kgdb context) and the normal Linux handlers can
only consume new input values after kgdb switched back.

This is not true anymore when RX DMA is enabled for UARTDM controllers.
Single input values can no longer be received correctly. Instead following
seems to happen:

* on 1. input, some old input is read (continuously)
* on 2. input, two old inputs are read (continuously)
* on 3. input, three old input values are read (continuously)
* on 4. input, 4 previous inputs are received

This repeats then for each group of 4 input values.

This behavior changes slightly depending on what state the controller was
when the first input was received. But this makes working with kgdb
basically impossible because control messages are always corrupted when
kgdboc tries to parse them.

RX DMA should therefore be off when CONSOLE_POLLING is enabled to avoid
these kind of problems. No such problem was noticed for TX DMA.

Fixes: 99693945013a ("tty: serial: msm: Add RX DMA support")
Cc: stable@vger.kernel.org
Signed-off-by: Sven Eckelmann 
Link: https://lore.kernel.org/r/20211113121050.7266-1-sven@narfation.org
Signed-off-by: Greg Kroah-Hartman

serial: 8250_dw: Drop wrong use of ACPI_PTR()

2021-11-26T10:58:40+00:00

[ Upstream commit ebabb77a2a115b6c5e68f7364b598310b5f61fb2 ]

ACPI_PTR() is more harmful than helpful. For example, in this case
if CONFIG_ACPI=n, the ID table left unused which is not what we want.

Instead of adding ifdeffery here and there, drop ACPI_PTR().

Fixes: 6a7320c4669f ("serial: 8250_dw: Add ACPI 5.0 support")
Reported-by: Daniel Palmer 
Signed-off-by: Andy Shevchenko 
Link: https://lore.kernel.org/r/20211005134516.23218-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Sasha Levin

serial: 8250_pci: make setup_port() parameters explicitly unsigned

2021-09-22T09:41:25+00:00

[ Upstream commit 3a96e97ab4e835078e6f27b7e1c0947814df3841 ]

The bar and offset parameters to setup_port() are used in pointer math,
and while it would be very difficult to get them to wrap as a negative
number, just be "safe" and make them unsigned so that static checkers do
not trip over them unintentionally.

Cc: Jiri Slaby 
Reported-by: Jordy Zomer 
Link: https://lore.kernel.org/r/20210726130717.2052096-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Sasha Levin

serial: 8250: Define RX trigger levels for OxSemi 950 devices

2021-09-22T09:41:25+00:00

[ Upstream commit d7aff291d069c4418285f3c8ee27b0ff67ce5998 ]

Oxford Semiconductor 950 serial port devices have a 128-byte FIFO and in
the enhanced (650) mode, which we select in `autoconfig_has_efr' with
the ECB bit set in the EFR register, they support the receive interrupt
trigger level selectable with FCR bits 7:6 from the set of 16, 32, 112,
120.  This applies to the original OX16C950 discrete UART[1] as well as
950 cores embedded into more complex devices.

For these devices we set the default to 112, which sets an excessively
high level of 112 or 7/8 of the FIFO capacity, unlike with other port
types where we choose at most 1/2 of their respective FIFO capacities.
Additionally we don't make the trigger level configurable.  Consequently
frequent input overruns happen with high bit rates where hardware flow
control cannot be used (e.g. terminal applications) even with otherwise
highly-performant systems.

Lower the default receive interrupt trigger level to 32 then, and make
it configurable.  Document the trigger levels along with other port
types, including the set of 16, 32, 64, 112 for the transmit interrupt
as well[2].

References:

[1] "OX16C950 rev B High Performance UART with 128 byte FIFOs", Oxford
    Semiconductor, Inc., DS-0031, Sep 05, Table 10: "Receiver Trigger
    Levels", p. 22

[2] same, Table 9: "Transmit Interrupt Trigger Levels", p. 22

Signed-off-by: Maciej W. Rozycki 
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2106260608480.37803@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Sasha Levin

tty: serial: jsm: hold port lock when reporting modem line changes

2021-09-22T09:41:24+00:00

[ Upstream commit 240e126c28df084222f0b661321e8e3ecb0d232e ]

uart_handle_dcd_change() requires a port lock to be held and will emit a
warning when lockdep is enabled.

Held corresponding lock to fix the following warnings.

[  132.528648] WARNING: CPU: 5 PID: 11600 at drivers/tty/serial/serial_core.c:3046 uart_handle_dcd_change+0xf4/0x120
[  132.530482] Modules linked in:
[  132.531050] CPU: 5 PID: 11600 Comm: jsm Not tainted 5.14.0-rc1-00003-g7fef2edf7cc7-dirty #31
[  132.535268] RIP: 0010:uart_handle_dcd_change+0xf4/0x120
[  132.557100] Call Trace:
[  132.557562]  ? __free_pages+0x83/0xb0
[  132.558213]  neo_parse_modem+0x156/0x220
[  132.558897]  neo_param+0x399/0x840
[  132.559495]  jsm_tty_open+0x12f/0x2d0
[  132.560131]  uart_startup.part.18+0x153/0x340
[  132.560888]  ? lock_is_held_type+0xe9/0x140
[  132.561660]  uart_port_activate+0x7f/0xe0
[  132.562351]  ? uart_startup.part.18+0x340/0x340
[  132.563003]  tty_port_open+0x8d/0xf0
[  132.563523]  ? uart_set_options+0x1e0/0x1e0
[  132.564125]  uart_open+0x24/0x40
[  132.564604]  tty_open+0x15c/0x630

Signed-off-by: Zheyu Ma 
Link: https://lore.kernel.org/r/1626242003-3809-1-git-send-email-zheyuma97@gmail.com
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Sasha Levin

serial: 8250: Mask out floating 16/32-bit bus bits

2021-08-15T10:59:56+00:00

commit e5227c51090e165db4b48dcaa300605bfced7014 upstream.

Make sure only actual 8 bits of the IIR register are used in determining
the port type in `autoconfig'.

The `serial_in' port accessor returns the `unsigned int' type, meaning
that with UPIO_AU, UPIO_MEM16, UPIO_MEM32, and UPIO_MEM32BE access types
more than 8 bits of data are returned, of which the high order bits will
often come from bus lines that are left floating in the data phase.  For
example with the MIPS Malta board's CBUS UART, where the registers are
aligned on 8-byte boundaries and which uses 32-bit accesses, data as
follows is returned:

YAMON> dump -32 0xbf000900 0x40

BF000900: 1F000942 1F000942 1F000900 1F000900  ...B...B........
BF000910: 1F000901 1F000901 1F000900 1F000900  ................
BF000920: 1F000900 1F000900 1F000960 1F000960  ...........`...`
BF000930: 1F000900 1F000900 1F0009FF 1F0009FF  ................

YAMON>

Evidently high-order 24 bits return values previously driven in the
address phase (the 3 highest order address bits used with the command
above are masked out in the simple virtual address mapping used here and
come out at zeros on the external bus), a common scenario with bus lines
left floating, due to bus capacitance.

Consequently when the value of IIR, mapped at 0x1f000910, is retrieved
in `autoconfig', it comes out at 0x1f0009c1 and when it is right-shifted
by 6 and then assigned to 8-bit `scratch' variable, the value calculated
is 0x27, not one of 0, 1, 2, 3 expected in port type determination.

Fix the issue then, by assigning the value returned from `serial_in' to
`scratch' first, which masks out 24 high-order bits retrieved, and only
then right-shift the resulting 8-bit data quantity, producing the value
of 3 in this case, as expected.  Fix the same issue in `serial_dl_read'.

The problem first appeared with Linux 2.6.9-rc3 which predates our repo
history, but the origin could be identified with the old MIPS/Linux repo
also at: 
as commit e0d2356c0777 ("Merge with Linux 2.6.9-rc3."), where code in
`serial_in' was updated with this case:

+	case UPIO_MEM32:
+		return readl(up->port.membase + offset);
+

which made it produce results outside the unsigned 8-bit range for the
first time, though obviously it is system dependent what actual values
appear in the high order bits retrieved and it may well have been zeros
in the relevant positions with the system the change originally was
intended for.  It is at that point that code in `autoconf' should have
been updated accordingly, but clearly it was overlooked.

Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Cc: stable@vger.kernel.org # v2.6.12+
Reviewed-by: Philippe Mathieu-Daudé 
Signed-off-by: Maciej W. Rozycki 
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2106260516220.37803@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman

tty: serial: 8250: serial_cs: Fix a memory leak in error handling path

2021-07-20T14:22:41+00:00

[ Upstream commit fad92b11047a748c996ebd6cfb164a63814eeb2e ]

In the probe function, if the final 'serial_config()' fails, 'info' is
leaking.

Add a resource handling path to free this memory.

Signed-off-by: Christophe JAILLET 
Link: https://lore.kernel.org/r/dc25f96b7faebf42e60fe8d02963c941cf4d8124.1621971720.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Sasha Levin

tty: serial: fsl_lpuart: fix the potential risk of division or modulo by zero

2021-07-20T14:22:40+00:00

[ Upstream commit fcb10ee27fb91b25b68d7745db9817ecea9f1038 ]

We should be very careful about the register values that will be used
for division or modulo operations, althrough the possibility that the
UARTBAUD register value is zero is very low, but we had better to deal
with the "bad data" of hardware in advance to avoid division or modulo
by zero leading to undefined kernel behavior.

Signed-off-by: Sherry Sun 
Link: https://lore.kernel.org/r/20210427021226.27468-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Sasha Levin

serial_cs: Add Option International GSM-Ready 56K/ISDN modem

2021-07-20T14:22:31+00:00

commit d495dd743d5ecd47288156e25c4d9163294a0992 upstream.

Add support for Option International GSM-Ready 56K/ISDN PCMCIA modem
card.

Signed-off-by: Ondrej Zary 
Cc: stable 
Link: https://lore.kernel.org/r/20210611201940.23898-2-linux@zary.sk
Signed-off-by: Greg Kroah-Hartman