linux-stable.git/drivers/tty/serial, branch v4.4.26

serial: 8250: added acces i/o products quad and octal serial cards

2016-09-24T08:07:38+00:00

commit c8d192428f52f244130b84650ad616df09f2b1e1 upstream.

Added devices ids for acces i/o products quad and octal serial cards
that make use of existing Pericom PI7C9X7954 and PI7C9X7958
configurations .

Signed-off-by: Jimi Damon 
Signed-off-by: Greg Kroah-Hartman

serial: 8250_mid: fix divide error bug if baud rate is 0

2016-09-24T08:07:38+00:00

commit 47b34d2ef266e2c283b514d65c8963c2ccd42474 upstream.

Since the commit c1a67b48f6a5 ("serial: 8250_pci: replace switch-case by
formula for Intel MID"), the 8250 driver crashes in the byt_set_termios()
function with a divide error. This is caused by the fact that a baud rate of 0
(B0) is not handled properly. Fix it by falling back to B9600 in this case.

Reported-by: "Mendez Salinas, Fernando" 
Fixes: c1a67b48f6a5 ("serial: 8250_pci: replace switch-case by formula for Intel MID")
Signed-off-by: Andy Shevchenko 
Signed-off-by: Greg Kroah-Hartman

tty/serial: atmel: fix RS485 half duplex with DMA

2016-08-20T16:09:17+00:00

commit 0058f0871efe7b01c6f2b3046c68196ab73e96da upstream.

When using DMA, half duplex doesn't work properly because rx is not stopped
before starting tx. Ensure we call atmel_stop_rx() in the DMA case.

Signed-off-by: Alexandre Belloni 
Acked-by: Nicolas Ferre 
Signed-off-by: Greg Kroah-Hartman

serial: samsung: Fix ERR pointer dereference on deferred probe

2016-08-20T16:09:17+00:00

commit e51e4d8a185de90424b03f30181b35f29c46a25a upstream.

When the clk_get() of "uart" clock returns EPROBE_DEFER, the next re-probe
finishes with success but uses invalid (ERR_PTR) values.  This leads to
dereferencing of ERR_PTR stored under ourport->clk:

	12c30000.serial: Controller clock not found
	(...)
	12c30000.serial: ttySAC3 at MMIO 0x12c30000 (irq = 61, base_baud = 0) is a S3C6400/10
	Unable to handle kernel paging request at virtual address fffffdfb

	(clk_prepare) from [] (s3c24xx_serial_pm+0x20/0x128)
	(s3c24xx_serial_pm) from [] (uart_change_pm+0x38/0x40)
	(uart_change_pm) from [] (uart_add_one_port+0x31c/0x44c)
	(uart_add_one_port) from [] (s3c24xx_serial_probe+0x2a8/0x418)
	(s3c24xx_serial_probe) from [] (platform_drv_probe+0x50/0xb0)
	(platform_drv_probe) from [] (driver_probe_device+0x1f4/0x2b0)
	(driver_probe_device) from [] (bus_for_each_drv+0x44/0x8c)
	(bus_for_each_drv) from [] (__device_attach+0x9c/0x100)
	(__device_attach) from [] (bus_probe_device+0x84/0x8c)
	(bus_probe_device) from [] (deferred_probe_work_func+0x60/0x8c)
	(deferred_probe_work_func) from [] (process_one_work+0x120/0x328)
	(process_one_work) from [] (worker_thread+0x2c/0x4ac)
	(worker_thread) from [] (kthread+0xd8/0xf4)
	(kthread) from [] (ret_from_fork+0x14/0x3c)

The first unsuccessful clk_get() causes s3c24xx_serial_init_port() to
exit with failure but the s3c24xx_uart_port is left half-configured
(e.g. port->mapbase is set, clk contains ERR_PTR).  On next re-probe,
the function s3c24xx_serial_init_port() will exit early with success
because of configured port->mapbase and driver will use old values,
including the ERR_PTR as clock.

Fix this by cleaning the port->mapbase on error path so each re-probe
will initialize all of the port settings.

Fixes: 60e93575476f ("serial: samsung: enable clock before clearing pending interrupts during init")
Signed-off-by: Krzysztof Kozlowski 
Reviewed-by: Javier Martinez Canillas 
Tested-by: Javier Martinez Canillas 
Tested-by: Kevin Hilman 
Signed-off-by: Greg Kroah-Hartman

tty: serial: msm: Don't read off end of tx fifo

2016-08-20T16:09:16+00:00

commit 30acf549ca1e81859a67590ab9ecfce3d1050a0b upstream.

For dm uarts in pio mode tx data is transferred to the fifo register 4
bytes at a time, but care is not taken when these 4 bytes spans the end
of the xmit buffer so the loop might read up to 3 bytes past the buffer
and then skip the actual data at the beginning of the buffer.

Fix this by, analogous to the DMA case, make sure the chunk doesn't
wrap the xmit buffer.

Fixes: 3a878c430fd6 ("tty: serial: msm: Add TX DMA support")
Cc: Ivan Ivanov 
Reported-by: Frank Rowand 
Reported-by: Nicolas Dechesne 
Signed-off-by: Bjorn Andersson 
Acked-by: Andy Gross 
Tested-by: Frank Rowand 
Reviewed-by: Stephen Boyd 
Signed-off-by: Greg Kroah-Hartman

QE-UART: add "fsl,t1040-ucc-uart" to of_device_id

2016-06-08T01:14:35+00:00

commit 11ca2b7ab432eb90906168c327733575e68d388f upstream.

New bindings use "fsl,t1040-ucc-uart" as the compatible for qe-uart.
So add it.

Signed-off-by: Zhao Qiang 
Signed-off-by: Greg Kroah-Hartman

serial: samsung: Reorder the sequence of clock control when call s3c24xx_serial_set_termios()

2016-06-01T19:15:53+00:00

commit b8995f527aac143e83d3900ff39357651ea4e0f6 upstream.

This patch fixes the broken serial log when changing the clock source
of uart device. Before disabling the original clock source, this patch
enables the new clock source to protect the clock off state for a split second.

Signed-off-by: Chanwoo Choi 
Reviewed-by: Marek Szyprowski 
Signed-off-by: Greg Kroah-Hartman 
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Krzysztof Kozlowski

serial: 8250_mid: recognize interrupt source in handler

2016-06-01T19:15:53+00:00

commit c42850f1ae7e70056f852e67bb9dddf927853b47 upstream.

There is a special register that shows interrupt status by source. In
particular case the source can be a combination of DMA Tx, DMA Rx, and UART.

Read the register and call the handlers only for sources that request an
interrupt.

Fixes: 6ede6dcd87aa ("serial: 8250_mid: add support for DMA engine handling from UART MMIO")
Reviewed-by: Heikki Krogerus 
Signed-off-by: Andy Shevchenko 
Signed-off-by: Greg Kroah-Hartman

serial: 8250_mid: use proper bar for DNV platform

2016-06-01T19:15:53+00:00

commit 107e15fc1f8d6ef69eac5f175971252f76e82f0d upstream.

Unlike Intel Medfield and Tangier platforms DNV uses PCI BAR0 for IO compatible
resources and BAR1 for MMIO. We need latter in a way to support DMA. Introduce
an additional field in the internal structure and pass PCI BAR based on device
ID.

Reported-by: "Lai, Poey Seng" 
Fixes: 6ede6dcd87aa ("serial: 8250_mid: add support for DMA engine handling from UART MMIO")
Reviewed-by: Heikki Krogerus 
Signed-off-by: Andy Shevchenko 
Signed-off-by: Greg Kroah-Hartman

serial: 8250_pci: fix divide error bug if baud rate is 0

2016-06-01T19:15:52+00:00

commit 6f210c18c1c0f016772c8cd51ae12a02bfb9e7ef upstream.

Since commit 21947ba654a6 ("serial: 8250_pci: replace switch-case by
formula"), the 8250 driver crashes in the byt_set_termios() function
with a divide error. This is caused by the fact that a baud rate of 0 (B0)
is not handled properly. Fix it by falling back to B9600 in this case.

Signed-off-by: David Müller 
Fixes: 21947ba654a6 ("serial: 8250_pci: replace switch-case by formula")
Suggested-by: Andy Shevchenko 
Reviewed-by: Andy Shevchenko 
Signed-off-by: Greg Kroah-Hartman