commit 5d24f455c182d5116dd5db8e1dc501115ecc9c2c upstream. The datasheet states: Bit 4: ClockEnSet the ClockEn bit high to enable an external clocking (crystal or clock generator at XIN). Set the ClockEn bit to 0 to disable clocking Bit 1: CrystalEnSet the CrystalEn bit high to enable the crystal oscillator. When using an external clock source at XIN, CrystalEn must be set low. The bit 4, MAX310X_CLKSRC_EXTCLK_BIT, should be set and was not. This was required to make the MAX3107 with an external crystal on our board able to send or receive data. Signed-off-by: Joe Burmeister <joe.burmeister@devtank.co.uk> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 61c0e37950b88bad590056286c1d766b1f167f4e upstream.
When the tty layer requests the uart to throttle, the current code
executing in msm_serial will trigger "Bad mode in Error Handler" and
generate an invalid stack frame in pstore before rebooting (that is if
pstore is indeed configured: otherwise the user shall just notice a
reboot with no further information dumped to the console).
This patch replaces the PIO byte accessor with the word accessor
already used in PIO mode.
Fixes: 68252424a7c7 ("tty: serial: msm: Support big-endian CPUs")
Cc: stable@vger.kernel.org
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ac0cdb3d990108df795b676cd0d0e65ac34b2273 ] Add the missing uart_unregister_driver() and i2c_del_driver() before return from sc16is7xx_init() in the error handling case. Signed-off-by: Mao Wenan <maowenan@huawei.com> Reviewed-by: Vladimir Zapolskiy <vz@mleia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
[ Upstream commit 4bb1ce2350a598502b23088b169e16b43d4bc639 ] When console device is rebinded, console_setup() is called again. But marking it as __init means that function will be clear after boot is complete. If console device is binded again console_setup() is not found and error "Unable to handle kernel paging request at virtual address" is reported. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 69646d7a3689fbe1a65ae90397d22ac3f1b8d40f upstream.
In half-duplex operation, RX should be started after TX completes.
If DMA is used, there is a case when the DMA transfer completes but the
TX FIFO is not emptied, so the RX cannot be restarted just yet.
Use a boolean variable to store this state and rearm TX interrupt mask
to be signaled again that the transfer finished. In interrupt transmit
handler this variable is used to start RX. A warning message is generated
if RX is activated before TX fifo is cleared.
Fixes: b389f173aaa1 ("tty/serial: atmel: RS485 half duplex w/DMA: enable
RX after TX is done")
Signed-off-by: Razvan Stefanescu <razvan.stefanescu@microchip.com>
Acked-by: Richard Genoud <richard.genoud@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f3040983132bf3477acd45d2452a906e67c2fec9 upstream.
Use a helper function to check that a port needs to use half duplex
communication, replacing several occurrences of multi-line bit checking.
Fixes: b389f173aaa1 ("tty/serial: atmel: RS485 half duplex w/DMA: enable RX after TX is done")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Razvan Stefanescu <razvan.stefanescu@microchip.com>
Acked-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3ec8002951ea173e24b466df1ea98c56b7920e63 upstream.
Echo "" to /sys/module/kgdboc/parameters/kgdboc will fail with "No such
device” error.
This is caused by function "configure_kgdboc" who init err to ENODEV
when the config is empty (legal input) the code go out with ENODEV
returned.
Fixes: 2dd453168643 ("kgdboc: Fix restrict error")
Signed-off-by: Wentao Wang <witallwang@gmail.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 93bcefd4c6bad4c69dbc4edcd3fbf774b24d930d upstream. We disable transmission interrupt (clear SCSCR_TIE) after all data has been transmitted (if uart_circ_empty(xmit)). While transmitting, if the data is still in the tty buffer, re-enable the SCSCR_TIE bit, which was done at sci_start_tx(). This is unnecessary processing, wasting CPU operation if the data transmission length is large. And further, transmit end, FIFO empty bits disabling have also been performed in the step above. Signed-off-by: Hoan Nguyen An <na-hoan@jinso.co.jp> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3a10e3dd52e80b9a97a3346020024d17b2c272d6 upstream. of_match_device can return a NULL pointer when matching device is not found. This patch avoids a scenario causing NULL pointer derefernce. Signed-off-by: Aditya Pakki <pakki001@umn.edu> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c85be041065c0be8bc48eda4c45e0319caf1d0e5 upstream.
In case dmaengine_prep_dma_cyclic fails, the fix returns a proper
error code to avoid NULL pointer dereference.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Fixes: 34df42f59a60 ("serial: at91: add rx dma support")
Acked-by: Richard Genoud <richard.genoud@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>