linux-stable.git/drivers/tty/serial, branch v4.4.124

serial: 8250_pci: Add Brainboxes UC-260 4 port serial device

2018-03-18T10:17:53+00:00

commit 9f2068f35729948bde84d87a40d135015911345d upstream.

Add PCI ids for two variants of Brainboxes UC-260 quad port
PCI serial cards.

Suggested-by: Andy Shevchenko 
Signed-off-by: Nikola Ciprich 
Cc: stable 
Signed-off-by: Greg Kroah-Hartman

tty/serial: atmel: add new version check for usart

2018-03-18T10:17:53+00:00

commit fd63a8903a2c40425a9811c3371dd4d0f42c0ad3 upstream.

On our at91sam9260 based board the usart0 and usart1 ports report
their versions (ATMEL_US_VERSION) as 0x10302. This version is not
included in the current checks in the driver.

Signed-off-by: Jonas Danielsson 
Acked-by: Richard Genoud 
Acked-by: Nicolas Ferre 
Cc: stable 
Signed-off-by: Greg Kroah-Hartman

serial: sh-sci: prevent lockup on full TTY buffers

2018-03-18T10:17:53+00:00

commit 7842055bfce4bf0170d0f61df8b2add8399697be upstream.

When the TTY buffers fill up to the configured maximum, a system lockup
occurs:

[  598.820128] INFO: rcu_preempt detected stalls on CPUs/tasks:
[  598.825796]  0-...!: (1 GPs behind) idle=5a6/2/0 softirq=1974/1974 fqs=1
[  598.832577]  (detected by 3, t=62517 jiffies, g=296, c=295, q=126)
[  598.838755] Task dump for CPU 0:
[  598.841977] swapper/0       R  running task        0     0      0 0x00000022
[  598.849023] Call trace:
[  598.851476]  __switch_to+0x98/0xb0
[  598.854870]            (null)

This can be prevented by doing a dummy read of the RX data register.

This issue affects both HSCIF and SCIF ports. Reported for R-Car H3 ES2.0;
reproduced and fixed on H3 ES1.1. Probably affects other R-Car platforms
as well.

Reported-by: Yoshihiro Shimoda 
Signed-off-by: Ulrich Hecht 
Reviewed-by: Geert Uytterhoeven 
Cc: stable 
Tested-by: Nguyen Viet Dung 
Signed-off-by: Greg Kroah-Hartman

serial: 8250_mid: fix broken DMA dependency

2018-02-25T10:03:49+00:00

commit 0ff4230584320b2153752ba54e2e8edbd6addf2c upstream.

In order to enable HSU DMA PCI driver, the HSU DMA Engine
must be enabled. This add a check for that.

Reported-by: kbuild test robot 
Signed-off-by: Heikki Krogerus 
Signed-off-by: Greg Kroah-Hartman

serial: imx: Only wakeup via RTSDEN bit if the system has RTS/CTS

2018-02-03T16:04:30+00:00

commit 38b1f0fb42f772b8c9aac53593883a18ff5eb9d7 upstream.

The wakeup mechanism via RTSDEN bit relies on the system using the RTS/CTS
lines, so only allow such wakeup method when the system actually has
RTS/CTS support.

Fixes: bc85734b126f ("serial: imx: allow waking up on RTSD")
Signed-off-by: Fabio Estevam 
Reviewed-by: Martin Kaiser 
Acked-by: Fugang Duan 
Signed-off-by: Greg Kroah-Hartman

serial: 8250: Preserve DLD[7:4] for PORT_XR17V35X

2017-12-09T17:42:40+00:00

[ Upstream commit 0ab84da2e076948c49d36197ee7d254125c53eab ]

The upper four bits of the XR17V35x fractional divisor register (DLD)
control general chip function (RS-485 direction pin polarity, multidrop
mode, XON/XOFF parity check, and fast IR mode). Don't allow these bits
to be clobbered when setting the baudrate.

Signed-off-by: Aaron Sierra 
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman

serial: 8250_fintek: Fix rs485 disablement on invalid ioctl()

2017-12-09T17:42:39+00:00

[ Upstream commit 3236a965486ba0c6043cf2c7b51943d8b382ae29 ]

This driver's ->rs485_config callback checks if SER_RS485_RTS_ON_SEND
and SER_RS485_RTS_AFTER_SEND have the same value.  If they do, it means
the user has passed in invalid data with the TIOCSRS485 ioctl()
since RTS must have a different polarity when sending and when not
sending.  In this case, rs485 mode is not enabled (the RS485_URA bit
is not set in the RS485 Enable Register) and this is supposed to be
signaled back to the user by clearing the SER_RS485_ENABLED bit in
struct serial_rs485 ... except a missing tilde character is preventing
that from happening.

Fixes: 28e3fb6c4dce ("serial: Add support for Fintek F81216A LPC to 4 UART")
Cc: Ricardo Ribalda Delgado 
Cc: "Ji-Ze Hong (Peter Hong)" 
Signed-off-by: Lukas Wunner 
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman

serial: 8250_pci: Add Amazon PCI serial device ID

2017-12-09T17:42:38+00:00

commit 3bfd1300abfe3adb18e84a89d97a0e82a22124bb upstream.

This device will be used in future Amazon EC2 instances as the primary
serial port (i.e., data sent to this port will be available via the
GetConsoleOuput [1] EC2 API).

[1] http://docs.aws.amazon.com/AWSEC2/latest/APIReference/API_GetConsoleOutput.html

Signed-off-by: Matt Wilson 
Signed-off-by: Greg Kroah-Hartman

serial: omap: Fix EFR write on RTS deassertion

2017-11-24T07:32:24+00:00

commit 2a71de2f7366fb1aec632116d0549ec56d6a3940 upstream.

Commit 348f9bb31c56 ("serial: omap: Fix RTS handling") sought to enable
auto RTS upon manual RTS assertion and disable it on deassertion.
However it seems the latter was done incorrectly, it clears all bits in
the Extended Features Register *except* auto RTS.

Fixes: 348f9bb31c56 ("serial: omap: Fix RTS handling")
Cc: Peter Hurley 
Signed-off-by: Lukas Wunner 
Signed-off-by: Greg Kroah-Hartman

serial: sh-sci: Fix register offsets for the IRDA serial port

2017-11-15T16:13:10+00:00

[ Upstream commit a752ba18af8285e3eeda572f40dddaebff0c3621 ]

Even though most of its registers are 8-bit wide, the IRDA has two
16-bit registers that make it a 16-bit peripheral and not a 8-bit
peripheral with addresses shifted by one. Fix the registers offset in
the driver and the platform data regshift value.

Signed-off-by: Laurent Pinchart 
Reviewed-by: Geert Uytterhoeven 
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman