linux-stable.git/drivers/tty/serial, branch linux-4.17.y

serial: 8250_dw: Add ACPI support for uart on Broadcom SoC

2018-08-22T05:44:55+00:00

commit 784c29eda5b4e28c3a56aa90b3815f9a1b0cfdc1 upstream.

Add ACPI identifier HID for UART DW 8250 on Broadcom SoCs
to match the HID passed through ACPI tables to enable
UART controller.

Signed-off-by: Srinath Mannam 
Reviewed-by: Vladimir Olovyannikov 
Tested-by: Vladimir Olovyannikov 
Reviewed-by: Andy Shevchenko 
Cc: stable 
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Greg Kroah-Hartman

serial: 8250_dw: always set baud rate in dw8250_set_termios

2018-08-22T05:44:54+00:00

commit dfcab6ba573445c703235ab6c83758eec12d7f28 upstream.

dw8250_set_termios() doesn't set baud rate if the arg "old ktermios" is
NULL. This happens during resume.
Call Trace:
...
[   54.928108] dw8250_set_termios+0x162/0x170
[   54.928114] serial8250_set_termios+0x17/0x20
[   54.928117] uart_change_speed+0x64/0x160
[   54.928119] uart_resume_port
...

So the baud rate is not restored after S3 and breaks the apps who use
UART, for example, console and bluetooth etc.

We address this issue by setting the baud rate irrespective of arg
"old", just like the drivers for other 8250 IPs. This is tested with
Intel Broxton platform.

Signed-off-by: Chen Hu 
Fixes: 4e26b134bd17 ("serial: 8250_dw: clock rate handling for all ACPI platforms")
Cc: Heikki Krogerus 
Cc: stable 
Reviewed-by: Andy Shevchenko 
Signed-off-by: Greg Kroah-Hartman

serial: 8250_exar: Read INT0 from slave device, too

2018-08-22T05:44:54+00:00

commit 60ab0fafc4b652fcaf7cbc3bb8555a0cf1149c28 upstream.

The sleep wake-up refactoring that I introduced in

  commit c7e1b4059075 ("tty: serial: exar: Relocate sleep wake-up handling")

did not account for devices with a slave device on the expansion port.
This patch pokes the INT0 register in the slave device, if present, in
order to ensure that MSI interrupts don't get permanently "stuck"
because of a sleep wake-up interrupt as described here:

  commit 2c0ac5b48a35 ("serial: exar: Fix stuck MSIs")

This also converts an ioread8() to readb() in order to provide visual
consistency with the MMIO-only accessors used elsewhere in the driver.

Reported-by: Andy Shevchenko 
Signed-off-by: Aaron Sierra 
Fixes: c7e1b4059075 ("tty: serial: exar: Relocate sleep wake-up handling")
Reviewed-by: Andy Shevchenko 
Cc: stable 
Signed-off-by: Greg Kroah-Hartman

tty: serial: 8250: Revert NXP SC16C2552 workaround

2018-08-22T05:44:54+00:00

commit 47ac76662ca9c5852fd353093f19de3ae85f2e66 upstream.

Revert commit ecb988a3b7985913d1f0112f66667cdd15e40711: tty: serial:
8250: 8250_core: NXP SC16C2552 workaround

The above commit causes userland application to no longer write
correctly its first write to a dumb terminal connected to /dev/ttyS0.
This commit seems to be the culprit. It's as though the TX FIFO is being
reset during that write. What should be displayed is:

PSW 80000000 INST 00000000                           HALT
//

What is displayed is some variation of:

T 00000000           HAL//

Reverting this commit via this patch fixes my problem.

Signed-off-by: Mark Hounschell 
Fixes: ecb988a3b798 ("tty: serial: 8250: 8250_core: NXP SC16C2552 workaround")
Cc: stable 
Signed-off-by: Greg Kroah-Hartman

serial: 8250_pci: Remove stalled entries in blacklist

2018-07-08T13:32:18+00:00

commit 20dcff436e9fcd2e106b0ccc48a52206bc176d70 upstream.

After the commit

  7d8905d06405 ("serial: 8250_pci: Enable device after we check black list")

pure serial multi-port cards, such as CH355, got blacklisted and thus
not being enumerated anymore. Previously, it seems, blacklisting them
was on purpose to shut up pciserial_init_one() about record duplication.

So, remove the entries from blacklist in order to get cards enumerated.

Fixes: 7d8905d06405 ("serial: 8250_pci: Enable device after we check black list")
Reported-by: Matt Turner 
Cc: Sergej Pupykin 
Cc: Alexandr Petrenko 
Signed-off-by: Andy Shevchenko 
Reviewed-and-Tested-by: Matt Turner 
Cc: stable 
Signed-off-by: Greg Kroah-Hartman

serial: sh-sci: Use spin_{try}lock_irqsave instead of open coding version

2018-07-03T09:26:46+00:00

commit 8afb1d2c12163f77777f84616a8e9444d0050ebe upstream.

Commit 40f70c03e33a ("serial: sh-sci: add locking to console write
function to avoid SMP lockup") copied the strategy to avoid locking
problems in conjuncture with the console from the UART8250
driver. Instead using directly spin_{try}lock_irqsave(),
local_irq_save() followed by spin_{try}lock() was used. While this is
correct on mainline, for -rt it is a problem. spin_{try}lock() will
check if it is running in a valid context. Since the local_irq_save()
has already been executed, the context has changed and
spin_{try}lock() will complain. The reason why spin_{try}lock()
complains is that on -rt the spin locks are turned into mutexes and
therefore can sleep. Sleeping with interrupts disabled is not valid.

BUG: sleeping function called from invalid context at /home/wagi/work/rt/v4.4-cip-rt/kernel/locking/rtmutex.c:995
in_atomic(): 0, irqs_disabled(): 128, pid: 778, name: irq/76-eth0
CPU: 0 PID: 778 Comm: irq/76-eth0 Not tainted 4.4.126-test-cip22-rt14-00403-gcd03665c8318 #12
Hardware name: Generic RZ/G1 (Flattened Device Tree)
Backtrace:
[] (dump_backtrace) from [] (show_stack+0x18/0x1c)
 r7:c06b01f0 r6:60010193 r5:00000000 r4:c06b01f0
[] (show_stack) from [] (dump_stack+0x78/0x94)
[] (dump_stack) from [] (___might_sleep+0x134/0x194)
 r7:60010113 r6:c06d3559 r5:00000000 r4:ffffe000
[] (___might_sleep) from [] (rt_spin_lock+0x20/0x74)
 r5:c06f4d60 r4:c06f4d60
[] (rt_spin_lock) from [] (serial_console_write+0x100/0x118)
 r5:c06f4d60 r4:c06f4d60
[] (serial_console_write) from [] (call_console_drivers.constprop.15+0x10c/0x124)
 r10:c06d2894 r9:c04e18b0 r8:00000028 r7:00000000 r6:c06d3559 r5:c06d2798
 r4:c06b9914 r3:c02576e4
[] (call_console_drivers.constprop.15) from [] (console_unlock+0x32c/0x430)
 r10:c06d30d8 r9:00000028 r8:c06dd518 r7:00000005 r6:00000000 r5:c06d2798
 r4:c06d2798 r3:00000028
[] (console_unlock) from [] (vprintk_emit+0x394/0x4f0)
 r10:c06d2798 r9:c06d30ee r8:00000006 r7:00000005 r6:c06a78fc r5:00000027
 r4:00000003
[] (vprintk_emit) from [] (vprintk+0x28/0x30)
 r10:c060bd46 r9:00001000 r8:c06b9a90 r7:c06b9a90 r6:c06b994c r5:c06b9a3c
 r4:c0062fa8
[] (vprintk) from [] (vprintk_default+0x10/0x14)
[] (vprintk_default) from [] (printk+0x78/0x84)
[] (printk) from [] (credit_entropy_bits+0x17c/0x2cc)
 r3:00000001 r2:decade60 r1:c061a5ee r0:c061a523
 r4:00000006
[] (credit_entropy_bits) from [] (add_interrupt_randomness+0x160/0x178)
 r10:466e7196 r9:1f536000 r8:fffeef74 r7:00000000 r6:c06b9a60 r5:c06b9a3c
 r4:dfbcf680
[] (add_interrupt_randomness) from [] (irq_thread+0x1e8/0x248)
 r10:c006537c r9:c06cdf21 r8:c0064fcc r7:df791c24 r6:df791c00 r5:ffffe000
 r4:df525180
[] (irq_thread) from [] (kthread+0x108/0x11c)
 r10:00000000 r9:00000000 r8:c0065184 r7:df791c00 r6:00000000 r5:df791d00
 r4:decac000
[] (kthread) from [] (ret_from_fork+0x14/0x3c)
 r8:00000000 r7:00000000 r6:00000000 r5:c003fa9c r4:df791d00

Cc: Sebastian Andrzej Siewior 
Signed-off-by: Daniel Wagner 
Reviewed-by: Geert Uytterhoeven 
Signed-off-by: Greg Kroah-Hartman

tty: pl011: Avoid spuriously stuck-off interrupts

2018-06-16T07:18:22+00:00

commit 4a7e625ce50412a7711efa0f2ef0b96ce3826759 upstream.

Commit 9b96fbacda34 ("serial: PL011: clear pending interrupts")
clears the RX and receive timeout interrupts on pl011 startup, to
avoid a screaming-interrupt scenario that can occur when the
firmware or bootloader leaves these interrupts asserted.

This has been noted as an issue when running Linux on qemu [1].

Unfortunately, the above fix seems to lead to potential
misbehaviour if the RX FIFO interrupt is asserted _non_ spuriously
on driver startup, if the RX FIFO is also already full to the
trigger level.

Clearing the RX FIFO interrupt does not change the FIFO fill level.
In this scenario, because the interrupt is now clear and because
the FIFO is already full to the trigger level, no new assertion of
the RX FIFO interrupt can occur unless the FIFO is drained back
below the trigger level.  This never occurs because the pl011
driver is waiting for an RX FIFO interrupt to tell it that there is
something to read, and does not read the FIFO at all until that
interrupt occurs.

Thus, simply clearing "spurious" interrupts on startup may be
misguided, since there is no way to be sure that the interrupts are
truly spurious, and things can go wrong if they are not.

This patch instead clears the interrupt condition by draining the
RX FIFO during UART startup, after clearing any potentially
spurious interrupt.  This should ensure that an interrupt will
definitely be asserted if the RX FIFO subsequently becomes
sufficiently full.

The drain is done at the point of enabling interrupts only.  This
means that it will occur any time the UART is newly opened through
the tty layer.  It will not apply to polled-mode use of the UART by
kgdboc: since that scenario cannot use interrupts by design, this
should not matter.  kgdboc will interact badly with "normal" use of
the UART in any case: this patch makes no attempt to paper over
such issues.

This patch does not attempt to address the case where the RX FIFO
fills faster than it can be drained: that is a pathological
hardware design problem that is beyond the scope of the driver to
work around.  As a failsafe, the number of poll iterations for
draining the FIFO is limited to twice the FIFO size.  This will
ensure that the kernel at least boots even if it is impossible to
drain the FIFO for some reason.

[1] [Qemu-devel] [Qemu-arm] [PATCH] pl011: do not put into fifo
before enabled the interruption
https://lists.gnu.org/archive/html/qemu-devel/2018-01/msg06446.html

Reported-by: Wei Xu 
Cc: Russell King 
Cc: Linus Walleij 
Cc: Peter Maydell 
Fixes: 9b96fbacda34 ("serial: PL011: clear pending interrupts")
Signed-off-by: Dave Martin 
Cc: stable 
Tested-by: Wei Xu 
Signed-off-by: Greg Kroah-Hartman

serial: 8250: omap: Fix idling of clocks for unused uarts

2018-06-16T07:18:22+00:00

commit 13dc04d0e5fdc25c8f713ad23fdce51cf2bf96ba upstream.

I noticed that unused UARTs won't necessarily idle properly always
unless at least one byte tx transfer is done first.

After some debugging I narrowed down the problem to the scr register
dma configuration bits that need to be set before softreset for the
clocks to idle. Unless we do this, the module clkctrl idlest bits
may be set to 1 instead of 3 meaning the clock will never idle and
is blocking deeper idle states for the whole domain.

This might be related to the configuration done by the bootloader
or kexec booting where certain configurations cause the 8250 or
the clkctrl clock to jam in a way where setting of the scr bits
and reset is needed to clear it. I've tried diffing the 8250
registers for the various modes, but did not see anything specific.
So far I've only seen this on omap4 but I'm suspecting this might
also happen on the other clkctrl using SoCs considering they
already have a quirk enabled for UART_ERRATA_CLOCK_DISABLE.

Let's fix the issue by configuring scr before reset for basic dma
even if we don't use it. The scr register will be reset when we do
softreset few lines after, and we restore scr on resume. We should
do this for all the SoCs with UART_ERRATA_CLOCK_DISABLE quirk flag
set since the ones with UART_ERRATA_CLOCK_DISABLE are all based
using clkctrl similar to omap4.

Looks like both OMAP_UART_SCR_DMAMODE_1 | OMAP_UART_SCR_DMAMODE_CTL
bits are needed for the clkctrl to idle after a softreset.

And we need to add omap4 to also use the UART_ERRATA_CLOCK_DISABLE
for the related workaround to be enabled. This same compatible
value will also be used for omap5.

Fixes: cdb929e4452a ("serial: 8250_omap: workaround errata around idling UART after using DMA")
Cc: Keerthy 
Cc: Matthijs van Duin 
Cc: Sekhar Nori 
Cc: Tero Kristo 
Signed-off-by: Tony Lindgren 
Cc: stable 
Signed-off-by: Greg Kroah-Hartman

serial: samsung: fix maxburst parameter for DMA transactions

2018-06-16T07:18:22+00:00

commit aa2f80e752c75e593b3820f42c416ed9458fa73e upstream.

The best granularity of residue that DMA engine can report is in the BURST
units, so the serial driver must use MAXBURST = 1 and DMA_SLAVE_BUSWIDTH_1_BYTE
if it relies on exact number of bytes transferred by DMA engine.

Fixes: 62c37eedb74c ("serial: samsung: add dma reqest/release functions")
Signed-off-by: Marek Szyprowski 
Acked-by: Krzysztof Kozlowski 
Cc: stable 
Signed-off-by: Greg Kroah-Hartman

tty/serial: atmel: use port->name as name in request_irq()

2018-06-16T07:18:22+00:00

commit 9594b5be7ec110ed11acec58fa94f3f293668c85 upstream.

I was puzzled while looking at /proc/interrupts and random things showed
up between reboots. This occurred more often but I realised it later. The
"correct" output should be:
|38:      11861  atmel-aic5   2 Level     ttyS0

but I saw sometimes
|38:       6426  atmel-aic5   2 Level     tty1

and accounted it wrongly as correct. This is use after free and the
former example randomly got the "old" pointer which pointed to the same
content. With SLAB_FREELIST_RANDOM and HARDENED I even got
|38:       7067  atmel-aic5   2 Level     E=Started User Manager for UID 0

or other nonsense.
As it turns out the tty, pointer that is accessed in atmel_startup(), is
freed() before atmel_shutdown(). It seems to happen quite often that the
tty for ttyS0 is allocated and freed while ->shutdown is not invoked. I
don't do anything special - just a systemd boot :)

Use dev_name(&pdev->dev) as the IRQ name for request_irq(). This exists
as long as the driver is loaded so no use-after-free here.

Cc: stable@vger.kernel.org
Fixes: 761ed4a94582 ("tty: serial_core: convert uart_close to use tty_port_close")
Acked-by: Richard Genoud 
Acked-by: Rob Herring 
Signed-off-by: Sebastian Andrzej Siewior 
Signed-off-by: Greg Kroah-Hartman