linux-stable.git/drivers/tty/serial/8250, branch linux-3.12.y Linux kernel stable tree serial: 8250_pci: Add MKS Tenta SCOM-0800 and SCOM-0801 cards 2017-03-13T20:40:43+00:00 Ian Abbott abbotti@mev.co.uk 2017-02-03T20:25:00+00:00 7c060cffad3c523ab59d864cd52730c08b070fb7 commit 1c9c858e2ff8ae8024a3d75d2ed080063af43754 upstream. The MKS Instruments SCOM-0800 and SCOM-0801 cards (originally by Tenta Technologies) are 3U CompactPCI serial cards with 4 and 8 serial ports, respectively. The first 4 ports are implemented by an OX16PCI954 chip, and the second 4 ports are implemented by an OX16C954 chip on a local bus, bridged by the second PCI function of the OX16PCI954. The ports are jumper-selectable as RS-232 and RS-422/485, and the UARTs use a non-standard oscillator frequency of 20 MHz (base_baud = 1250000). Signed-off-by: Ian Abbott <abbotti@mev.co.uk> Signed-off-by: Jiri Slaby <jslaby@suse.cz> 
commit 1c9c858e2ff8ae8024a3d75d2ed080063af43754 upstream.

The MKS Instruments SCOM-0800 and SCOM-0801 cards (originally by Tenta
Technologies) are 3U CompactPCI serial cards with 4 and 8 serial ports,
respectively.  The first 4 ports are implemented by an OX16PCI954 chip,
and the second 4 ports are implemented by an OX16C954 chip on a local
bus, bridged by the second PCI function of the OX16PCI954.  The ports
are jumper-selectable as RS-232 and RS-422/485, and the UARTs use a
non-standard oscillator frequency of 20 MHz (base_baud = 1250000).

Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
serial: 8250_pci: Detach low-level driver during PCI error recovery 2017-01-27T16:15:00+00:00 Gabriel Krisman Bertazi krisman@linux.vnet.ibm.com 2016-11-28T21:34:42+00:00 b6580bd986df184845960c3abe490ed378ee1216 commit f209fa03fc9d131b3108c2e4936181eabab87416 upstream. During a PCI error recovery, like the ones provoked by EEH in the ppc64 platform, all IO to the device must be blocked while the recovery is completed. Current 8250_pci implementation only suspends the port instead of detaching it, which doesn't prevent incoming accesses like TIOCMGET and TIOCMSET calls from reaching the device. Those end up racing with the EEH recovery, crashing it. Similar races were also observed when opening the device and when shutting it down during recovery. This patch implements a more robust IO blockage for the 8250_pci recovery by unregistering the port at the beginning of the procedure and re-adding it afterwards. Since the port is detached from the uart layer, we can be sure that no request will make through to the device during recovery. This is similar to the solution used by the JSM serial driver. I thank Peter Hurley <peter@hurleysoftware.com> for valuable input on this one over one year ago. Signed-off-by: Gabriel Krisman Bertazi <krisman@linux.vnet.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz> 
commit f209fa03fc9d131b3108c2e4936181eabab87416 upstream.

During a PCI error recovery, like the ones provoked by EEH in the ppc64
platform, all IO to the device must be blocked while the recovery is
completed.  Current 8250_pci implementation only suspends the port
instead of detaching it, which doesn't prevent incoming accesses like
TIOCMGET and TIOCMSET calls from reaching the device.  Those end up
racing with the EEH recovery, crashing it.  Similar races were also
observed when opening the device and when shutting it down during
recovery.

This patch implements a more robust IO blockage for the 8250_pci
recovery by unregistering the port at the beginning of the procedure and
re-adding it afterwards.  Since the port is detached from the uart
layer, we can be sure that no request will make through to the device
during recovery.  This is similar to the solution used by the JSM serial
driver.

I thank Peter Hurley <peter@hurleysoftware.com> for valuable input on
this one over one year ago.

Signed-off-by: Gabriel Krisman Bertazi <krisman@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
8250: use callbacks to access UART_DLL/UART_DLM 2016-04-11T14:44:13+00:00 Sebastian Frias sf84@laposte.net 2015-12-18T16:40:05+00:00 6294da6a1f8a1d6ae96d28f7188b8acad0b99996 commit 0b41ce991052022c030fd868e03877700220b090 upstream. Some UART HW has a single register combining UART_DLL/UART_DLM (this was probably forgotten in the change that introduced the callbacks, commit b32b19b8ffc05cbd3bf91c65e205f6a912ca15d9) Fixes: b32b19b8ffc0 ("[SERIAL] 8250: set divisor register correctly ...") Signed-off-by: Sebastian Frias <sf84@laposte.net> Reviewed-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz> 
commit 0b41ce991052022c030fd868e03877700220b090 upstream.

Some UART HW has a single register combining UART_DLL/UART_DLM
(this was probably forgotten in the change that introduced the
callbacks, commit b32b19b8ffc05cbd3bf91c65e205f6a912ca15d9)

Fixes: b32b19b8ffc0 ("[SERIAL] 8250: set divisor register correctly ...")

Signed-off-by: Sebastian Frias <sf84@laposte.net>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
serial: 8250_pci: Correct uartclk for xr17v35x expansion chips 2016-02-24T09:23:18+00:00 Soeren Grunewald soeren.grunewald@desy.de 2015-06-11T07:25:05+00:00 6bfc19b4c22da366a019505065c0225d2b0e3867 commit 899f0c1c7dbcc487fdc8756a49ff70b1d5d75f89 upstream. The internal clock of the master chip, which is usually 125MHz, is only half (62.5MHz) for the slave chips. So we have to adjust the uartclk for all the slave ports. Therefor we add a new function to determine if a slave chip is present and update pci_xr17v35x_setup accordingly. Signed-off-by: Soeren Grunewald <soeren.grunewald@desy.de> Signed-off-by: Jiri Slaby <jslaby@suse.cz> 
commit 899f0c1c7dbcc487fdc8756a49ff70b1d5d75f89 upstream.

The internal clock of the master chip, which is usually 125MHz, is only half
(62.5MHz) for the slave chips. So we have to adjust the uartclk for all the
slave ports. Therefor we add a new function to determine if a slave chip is
present and update pci_xr17v35x_setup accordingly.

Signed-off-by: Soeren Grunewald <soeren.grunewald@desy.de>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
serial: 8250_dw: Fix deadlock in LCR workaround 2015-11-14T17:58:27+00:00 Peter Hurley peter@hurleysoftware.com 2015-03-11T13:19:16+00:00 9bc623ed14f83e2facf5ada94405d39c2a7be3fd commit 7fd6f640f2dd17dac6ddd6702c378cb0bb9cfa11 upstream. Trying to write console output from within the serial console driver while the port->lock is held causes recursive deadlock: CPU 0 spin_lock_irqsave(&port->lock) printk() console_unlock() call_console_drivers() serial8250_console_write() spin_lock_irqsave(&port->lock) ** DEADLOCK ** The 8250_dw i/o accessors try to write a console error message if the LCR workaround was unsuccessful. When the port->lock is already held (eg., when called from serial8250_set_termios()), this deadlocks. Make the error message a FIXME until a general solution is devised. Cc: Tim Kryger <tim.kryger@gmail.com> Reported-by: Zhang Zhen <zhenzhang.zhang@huawei.com> Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz> 
commit 7fd6f640f2dd17dac6ddd6702c378cb0bb9cfa11 upstream.

Trying to write console output from within the serial console driver
while the port->lock is held causes recursive deadlock:

  CPU 0
spin_lock_irqsave(&port->lock)
printk()
  console_unlock()
    call_console_drivers()
      serial8250_console_write()
        spin_lock_irqsave(&port->lock)
** DEADLOCK **

The 8250_dw i/o accessors try to write a console error message if the
LCR workaround was unsuccessful. When the port->lock is already held
(eg., when called from serial8250_set_termios()), this deadlocks.

Make the error message a FIXME until a general solution is devised.

Cc: Tim Kryger <tim.kryger@gmail.com>
Reported-by: Zhang Zhen <zhenzhang.zhang@huawei.com>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
serial: 8250_pci: Add support for 12 port Exar boards 2015-11-12T13:09:06+00:00 Soeren Grunewald soeren.grunewald@desy.de 2015-06-11T07:25:04+00:00 cfcdadb344e6bce7f3a80da83322b36d5795c22e commit be32c0cf0462c36f482b5ddcff1d8371be1e183c upstream. The Exar XR17V358 can also be combined with a XR17V354 chip to act as a single 12 port chip. This works the same way as the combining two XR17V358 chips. But the reported device id then is 0x4358. Signed-off-by: Soeren Grunewald <soeren.grunewald@desy.de> Signed-off-by: Jiri Slaby <jslaby@suse.cz> 
commit be32c0cf0462c36f482b5ddcff1d8371be1e183c upstream.

The Exar XR17V358 can also be combined with a XR17V354 chip to act as a
single 12 port chip. This works the same way as the combining two XR17V358
chips. But the reported device id then is 0x4358.

Signed-off-by: Soeren Grunewald <soeren.grunewald@desy.de>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
serial: 8250_pci: Add support for 16 port Exar boards 2015-11-12T13:09:06+00:00 Soeren Grunewald soeren.grunewald@desy.de 2015-04-28T14:29:49+00:00 3e8c9dd24acc11db838781ca05305ed02484f2c3 commit 96a5d18bc1338786fecac73599f1681f59a59a8e upstream. The Exar XR17V358 chip usually provides only 8 ports. But two chips can be combined to act as a single 16 port chip. Therefor one chip is configured as master the second as slave by connecting the mode pin to VCC (master) or GND (slave). Then the master chip is reporting a different device-id depending on whether a slave is detected or not. The UARTs 8-15 are addressed from 0x2000-0x3fff. So the offset of 0x400 from UART to UART can be used to address all 16 ports as before. See: https://www.exar.com/common/content/document.ashx?id=1587 page 11 Signed-off-by: Soeren Grunewald <soeren.grunewald@desy.de> Signed-off-by: Jiri Slaby <jslaby@suse.cz> 
commit 96a5d18bc1338786fecac73599f1681f59a59a8e upstream.

The Exar XR17V358 chip usually provides only 8 ports. But two chips can be
combined to act as a single 16 port chip. Therefor one chip is configured
as master the second as slave by connecting the mode pin to VCC (master)
or GND (slave).

Then the master chip is reporting a different device-id depending on
whether a slave is detected or not. The UARTs 8-15 are addressed from
0x2000-0x3fff. So the offset of 0x400 from UART to UART can be used to
address all 16 ports as before.

See: https://www.exar.com/common/content/document.ashx?id=1587 page 11

Signed-off-by: Soeren Grunewald <soeren.grunewald@desy.de>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
serial: 8250: don't bind to SMSC IrCC IR port 2015-09-30T08:59:54+00:00 Maciej S. Szmigiero mail@maciej.szmigiero.name 2015-08-02T21:11:52+00:00 01e34fe8efcb116223840e7ceaa42a6dca9bcf98 commit ffa34de03bcfbfa88d8352942bc238bb48e94e2d upstream. SMSC IrCC SIR/FIR port should not be bound to by (legacy) serial driver so its own driver (smsc-ircc2) can bind to it. Signed-off-by: Maciej Szmigiero <mail@maciej.szmigiero.name> Signed-off-by: Jiri Slaby <jslaby@suse.cz> 
commit ffa34de03bcfbfa88d8352942bc238bb48e94e2d upstream.

SMSC IrCC SIR/FIR port should not be bound to by
(legacy) serial driver so its own driver (smsc-ircc2)
can bind to it.

Signed-off-by: Maciej Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Change email address for 8250_pci 2015-04-09T11:14:04+00:00 Russell King rmk+kernel@arm.linux.org.uk 2015-03-06T10:49:21+00:00 6be916ce95ab1159dea6e6bc89f465ee758f4e0d commit f2e0ea861117bda073d1d7ffbd3120c07c0d5d34 upstream. I'm still receiving reports to my email address, so let's point this at the linux-serial mailing list instead. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Jiri Slaby <jslaby@suse.cz> 
commit f2e0ea861117bda073d1d7ffbd3120c07c0d5d34 upstream.

I'm still receiving reports to my email address, so let's point this
at the linux-serial mailing list instead.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
parport: Add support for the WCH353 1S/1P multi-IO card 2014-11-19T22:30:56+00:00 Ezequiel Garcia ezequiel.garcia@free-electrons.com 2014-05-24T18:24:51+00:00 8d6960fa02a523485d20ae8bd4bf3b6731f00937 commit feb5814254094c306429fe6d7b9c534fa0250f4c upstream. This Multi-IO card has one serial 16550-like and one parallel port connector. Here's the lspci output, after this commit is applied: 03:07.0 Serial controller: Device 4348:5053 (rev 10) (prog-if 02 [16550]) Subsystem: Device 4348:5053 Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Interrupt: pin A routed to IRQ 21 Region 0: I/O ports at cf00 [size=8] Region 1: I/O ports at ce00 [size=8] Kernel driver in use: parport_serial Kernel modules: 8250_pci, parport_serial This commit adds an entry with the device ID to the blacklist declared in 8250_pci to prevent the driver from taking ownership. Also, and as was done for the 2S/1P variant, add a quirk to skip autodetection and set the correct type to 16550A clone. Proper entries are added to parport_serial, to support the device parallel and serial ports. Cc: Gianluca Anzolin <gianluca@sottospazio.it> Cc: Alan Cox <alan@linux.intel.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz> 
commit feb5814254094c306429fe6d7b9c534fa0250f4c upstream.

This Multi-IO card has one serial 16550-like and one parallel port connector.
Here's the lspci output, after this commit is applied:

03:07.0 Serial controller: Device 4348:5053 (rev 10) (prog-if 02 [16550])
	Subsystem: Device 4348:5053
	Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Interrupt: pin A routed to IRQ 21
	Region 0: I/O ports at cf00 [size=8]
	Region 1: I/O ports at ce00 [size=8]
	Kernel driver in use: parport_serial
	Kernel modules: 8250_pci, parport_serial

This commit adds an entry with the device ID to the blacklist declared in
8250_pci to prevent the driver from taking ownership. Also, and as was done
for the 2S/1P variant, add a quirk to skip autodetection and set the correct
type to 16550A clone.

Proper entries are added to parport_serial, to support the device parallel
and serial ports.

Cc: Gianluca Anzolin <gianluca@sottospazio.it>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>