commit 5d2569cb4a65c373896ec0217febdf88739ed295 upstream.

Software that has run before the USB4 CM in Linux runs may have disabled
hotplug events for a given lane adapter.

Other CMs such as that one distributed with Windows 11 will enable hotplug
events. Do the same thing in the Linux CM which fixes hotplug events on
"AMD Pink Sardine".

Cc: stable@vger.kernel.org
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

If any software has interacted with the USB4 registers before the Linux
USB4 CM runs, it may have modified the plug events delay. It has been
observed that if this value too large, it's possible that hotplugged
devices will negotiate a fallback mode instead in Linux.

To prevent this, explicitly align the plug events delay with the USB4
spec value of 10ms.

Cc: stable@vger.kernel.org
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

Only Thunderbolt 3 routers need the xHCI connection flow. This also
ensures the router actually has both lane adapters (1 and 3). While
there move declaration of the boolean variables inside the block where
they are being used.

Fixes: 30a4eca69b76 ("thunderbolt: Add internal xHCI connect flows for Thunderbolt 3 devices")
Cc: stable@vger.kernel.org
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

In this patch we add support for a second low power state of the link: CL1.
Low power states (called collectively CLx) are used to reduce
transmitter and receiver power when a high-speed lane is idle.
We enable it, if both sides of the link support it,
and only for the first hop router (i.e. the first device that connected
to the host router). This is needed for better thermal management.

Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

Fix few typos in CLx enabling.

Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

Disable CLx before system suspended only if previously was enabled.

Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

Sometimes when polling for the port after target link width is changed
we get back port locked notification (because the link actually was
reset and then re-trained). Instead of bailing out we can ignore these
when polling for the width change as this is expected.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

When bonding lanes over XDomain the host that has "higher" UUID triggers
link re-train for bonding, and the host that has "lower" UUID just waits
for this to happen. To support this split setting the link width and
triggering the actual bonding a separate functions that can be called as
needed.

While there remove duplicated empty line in the kernel-doc comment of
tb_port_lane_bonding_disable().

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

This is useful when debugging possible issues.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

The USB4 specification doesn't make any requirements that reading
a device router's DROM is needed for the operation of the device.

Other connection manager solutions don't necessarily read it or gate
the usability of the device on whether it was read.

So make failures when reading the DROM show warnings but not
fail the initialization of the router.

Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>