linux-stable.git/drivers/staging, branch v3.16.71

binder: Replace "%p" with "%pK" for stable

2019-07-09T21:04:20+00:00

This was done as part of upstream commits fdfb4a99b6ab "8inder:
separate binder allocator structure from binder proc", 19c987241ca1
"binder: separate out binder_alloc functions", and 7a4408c6bd3e
"binder: make sure accesses to proc/thread are safe".  However, those
commits made lots of other changes that are not suitable for stable.

Signed-off-by: Ben Hutchings 
Signed-off-by: Ben Hutchings

staging: android: ashmem: Avoid range_alloc() allocation with ashmem_mutex held.

2019-07-09T21:04:07+00:00

commit ecd182cbf4e107928077866399100228d2359c60 upstream.

ashmem_pin() is calling range_shrink() without checking whether
range_alloc() succeeded. Also, doing memory allocation with ashmem_mutex
held should be avoided because ashmem_shrink_scan() tries to hold it.

Therefore, move memory allocation for range_alloc() to ashmem_pin_unpin()
and make range_alloc() not to fail.

This patch is mostly meant for backporting purpose for fuzz testing on
stable/distributor kernels, for there is a plan to remove this code in
near future.

Signed-off-by: Tetsuo Handa 
Reviewed-by: Joel Fernandes 
Signed-off-by: Greg Kroah-Hartman 
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings

staging: iio: adt7316: fix the dac write calculation

2019-07-09T21:03:44+00:00

commit 78accaea117c1ae878774974fab91ac4a0b0e2b0 upstream.

The lsb calculation is not masking the correct bits from the user input.
Subtract 1 from (1 << offset) to correctly set up the mask to be applied
to user input.

The lsb register stores its value starting at the bit 7 position.
adt7316_store_DAC() currently assumes the value is at the other end of the
register. Shift the lsb value before storing it in a new variable lsb_reg,
and write this variable to the lsb register.

Fixes: 35f6b6b86ede ("staging: iio: new ADT7316/7/8 and ADT7516/7/9 driver")
Signed-off-by: Jeremy Fertic 
Signed-off-by: Jonathan Cameron 
Signed-off-by: Ben Hutchings

staging: iio: adt7316: fix the dac read calculation

2019-07-09T21:03:43+00:00

commit 45130fb030aec26ac28b4bb23344901df3ec3b7f upstream.

The calculation of the current dac value is using the wrong bits of the
dac lsb register. Create two macros to shift the lsb register value into
lsb position, depending on whether the dac is 10 or 12 bit. Initialize
data to 0 so, with an 8 bit dac, the msb register value can be bitwise
ORed with data.

Fixes: 35f6b6b86ede ("staging: iio: new ADT7316/7/8 and ADT7516/7/9 driver")
Signed-off-by: Jeremy Fertic 
Signed-off-by: Jonathan Cameron 
Signed-off-by: Ben Hutchings

staging: iio: adt7316: fix handling of dac high resolution option

2019-07-09T21:03:43+00:00

commit 76b7fe8d6c4daf4db672eb953c892c6f6572a282 upstream.

The adt7316/7 and adt7516/7 have the option to output voltage proportional
to temperature on dac a and/or dac b. The default dac resolution in this
mode is 8 bits with the dac high resolution option enabling 10 bits. None
of these settings affect dacs c and d. Remove the "1 (12 bits)" output from
the show function since that is not an option for this mode. Return
"1 (10 bits)" if the device is one of the above mentioned chips and the dac
high resolution mode is enabled.

In the store function, the driver currently allows the user to write to the
ADT7316_DA_HIGH_RESOLUTION bit regardless of the device in use. Add a check
to return an error in the case of an adt7318 or adt7519. Remove the else
statement that clears the ADT7316_DA_HIGH_RESOLUTION bit. Instead, clear it
before conditionally enabling it, depending on user input. This matches the
typical pattern in the driver when an attribute is a boolean.

Fixes: 35f6b6b86ede ("staging: iio: new ADT7316/7/8 and ADT7516/7/9 driver")
Signed-off-by: Jeremy Fertic 
Signed-off-by: Jonathan Cameron 
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings

staging: iio: adt7316: fix dac_bits assignment

2019-07-09T21:03:42+00:00

commit e9de475723de5bf207a5b7b88bdca863393e42c8 upstream.

The value of dac_bits is used in adt7316_show_DAC() and adt7316_store_DAC(),
and it should be either 8, 10, or 12 bits depending on the device in use. The
driver currently only assigns a value to dac_bits in
adt7316_store_da_high_resolution(). The purpose of the dac high resolution
option is not to change dac resolution for normal operation. Instead, it
is specific to an optional feature where one or two of the four dacs can
be set to output voltage proportional to temperature. If the user chooses
to set dac a and/or dac b to output voltage proportional to temperature,
the da_high_resolution attribute can optionally be enabled to use 10 bit
resolution rather than the default 8 bits. This is only available on the
10 and 12 bit dac devices. If the user attempts to read or write dacs a
or b under these settings, the driver's current behaviour is to return an
error. Dacs c and d continue to operate normally under these conditions.
With the above in mind, remove the dac_bits assignments from this function
since the value of dac_bits as used in the driver is not dependent on this
dac high resolution option.

Since the dac_bits assignments discussed above are currently the only ones
in this driver, the default value of dac_bits is 0. This results in incorrect
calculations when the dacs are read or written in adt7316_show_DAC() and
adt7316_store_DAC(). To correct this, assign a value to dac_bits in
adt7316_probe() to ensure correct operation as soon as the device is
registered and available to userspace.

Fixes: 35f6b6b86ede ("staging: iio: new ADT7316/7/8 and ADT7516/7/9 driver")
Signed-off-by: Jeremy Fertic 
Signed-off-by: Jonathan Cameron 
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings

staging: iio: adt7316: allow adt751x to use internal vref for all dacs

2019-07-09T21:03:39+00:00

commit 10bfe7cc1739c22f0aa296b39e53f61e9e3f4d99 upstream.

With adt7516/7/9, internal vref is available for dacs a and b, dacs c and
d, or all dacs. The driver doesn't currently support internal vref for all
dacs. Change the else if to an if so both bits are checked rather than
just one or the other.

Signed-off-by: Jeremy Fertic 
Fixes: 35f6b6b86ede ("staging: iio: new ADT7316/7/8 and ADT7516/7/9 driver")
Signed-off-by: Jonathan Cameron 
Signed-off-by: Ben Hutchings

staging: iio: adt7316: invert the logic of the check for an ldac pin

2019-07-09T21:03:39+00:00

commit 85a1c11913312132d0800ca2c1c42a011f96ea92 upstream.

ADT7316_DA_EN_VIA_DAC_LDCA is set when the dac and ldac registers are being
used to update the dacs instead of the ldac pin. ADT7516_SEL_AIN3 is an adc
input that shares the ldac pin. Only set these bits if an ldac pin is not
being used.

This could be backported to stable, but note there are various
other bugs that probably make that a waste of time.

Signed-off-by: Jeremy Fertic 
Fixes: 35f6b6b86ede ("staging: iio: new ADT7316/7/8 and ADT7516/7/9 driver")
Signed-off-by: Jonathan Cameron 
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings

staging: iio: adt7316: fix register and bit definitions

2019-07-09T21:03:38+00:00

commit 53a6f022b4fe8645468adaffca901dbf8c3c547e upstream.

Change two register addresses and one bit definition to match the
datasheet.

Note that there are many issues in this driver so I would
not suggest backporting these fixes to stable trees.

Signed-off-by: Jeremy Fertic 
Fixes: 35f6b6b86ede ("staging: iio: new ADT7316/7/8 and ADT7516/7/9 driver")
Signed-off-by: Jonathan Cameron 
Signed-off-by: Ben Hutchings

staging: rtl8188eu: Add device code for D-Link DWA-121 rev B1

2019-05-02T20:41:21+00:00

commit 5f74a8cbb38d10615ed46bc3e37d9a4c9af8045a upstream.

This device was added to the stand-alone driver on github.
Add it to the staging driver as well.

Link: https://github.com/lwfinger/rtl8188eu/commit/a0619a07cd1e
Signed-off-by: Michael Straube 
Acked-by: Larry Finger 
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Ben Hutchings