linux-stable.git/drivers/staging/comedi, branch v5.4.78

staging: comedi: cb_pcidas: Allow 2-channel commands for AO subdevice

2020-11-05T10:43:37+00:00

commit 647a6002cb41d358d9ac5de101a8a6dc74748a59 upstream.

The "cb_pcidas" driver supports asynchronous commands on the analog
output (AO) subdevice for those boards that have an AO FIFO.  The code
(in `cb_pcidas_ao_check_chanlist()` and `cb_pcidas_ao_cmd()`) to
validate and set up the command supports output to a single channel or
to two channels simultaneously (the boards have two AO channels).
However, the code in `cb_pcidas_auto_attach()` that initializes the
subdevices neglects to initialize the AO subdevice's `len_chanlist`
member, leaving it set to 0, but the Comedi core will "correct" it to 1
if the driver neglected to set it.  This limits commands to use a single
channel (either channel 0 or 1), but the limit should be two channels.
Set the AO subdevice's `len_chanlist` member to be the same value as the
`n_chan` member, which will be 2.

Cc: 
Signed-off-by: Ian Abbott 
Link: https://lore.kernel.org/r/20201021122142.81628-1-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman

staging: comedi: check validity of wMaxPacketSize of usb endpoints found

2020-10-17T08:11:23+00:00

commit e1f13c879a7c21bd207dc6242455e8e3a1e88b40 upstream.

While finding usb endpoints in vmk80xx_find_usb_endpoints(), check if
wMaxPacketSize = 0 for the endpoints found.

Some devices have isochronous endpoints that have wMaxPacketSize = 0
(as required by the USB-2 spec).
However, since this doesn't apply here, wMaxPacketSize = 0 can be
considered to be invalid.

Reported-by: syzbot+009f546aa1370056b1c2@syzkaller.appspotmail.com
Tested-by: syzbot+009f546aa1370056b1c2@syzkaller.appspotmail.com
Signed-off-by: Anant Thazhemadam 
Cc: stable 
Link: https://lore.kernel.org/r/20201010082933.5417-1-anant.thazhemadam@gmail.com
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Greg Kroah-Hartman

staging: comedi: addi_apci_1564: check INSN_CONFIG_DIGITAL_TRIG shift

2020-07-29T08:18:42+00:00

commit 926234f1b8434c4409aa4c53637aa3362ca07cea upstream.

The `INSN_CONFIG` comedi instruction with sub-instruction code
`INSN_CONFIG_DIGITAL_TRIG` includes a base channel in `data[3]`. This is
used as a right shift amount for other bitmask values without being
checked.  Shift amounts greater than or equal to 32 will result in
undefined behavior.  Add code to deal with this.

Fixes: 1e15687ea472 ("staging: comedi: addi_apci_1564: add Change-of-State interrupt subdevice and required functions")
Cc:  #3.17+
Signed-off-by: Ian Abbott 
Link: https://lore.kernel.org/r/20200717145257.112660-4-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman

staging: comedi: addi_apci_1500: check INSN_CONFIG_DIGITAL_TRIG shift

2020-07-29T08:18:42+00:00

commit fc846e9db67c7e808d77bf9e2ef3d49e3820ce5d upstream.

The `INSN_CONFIG` comedi instruction with sub-instruction code
`INSN_CONFIG_DIGITAL_TRIG` includes a base channel in `data[3]`. This is
used as a right shift amount for other bitmask values without being
checked.  Shift amounts greater than or equal to 32 will result in
undefined behavior.  Add code to deal with this, adjusting the checks
for invalid channels so that enabled channel bits that would have been
lost by shifting are also checked for validity.  Only channels 0 to 15
are valid.

Fixes: a8c66b684efaf ("staging: comedi: addi_apci_1500: rewrite the subdevice support functions")
Cc:  #4.0+: ef75e14a6c93: staging: comedi: verify array index is correct before using it
Cc:  #4.0+
Signed-off-by: Ian Abbott 
Link: https://lore.kernel.org/r/20200717145257.112660-5-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman

staging: comedi: ni_6527: fix INSN_CONFIG_DIGITAL_TRIG support

2020-07-29T08:18:42+00:00

commit f07804ec77d77f8a9dcf570a24154e17747bc82f upstream.

`ni6527_intr_insn_config()` processes `INSN_CONFIG` comedi instructions
for the "interrupt" subdevice.  When `data[0]` is
`INSN_CONFIG_DIGITAL_TRIG` it is configuring the digital trigger.  When
`data[2]` is `COMEDI_DIGITAL_TRIG_ENABLE_EDGES` it is configuring rising
and falling edge detection for the digital trigger, using a base channel
number (or shift amount) in `data[3]`, a rising edge bitmask in
`data[4]` and falling edge bitmask in `data[5]`.

If the base channel number (shift amount) is greater than or equal to
the number of channels (24) of the digital input subdevice, there are no
changes to the rising and falling edges, so the mask of channels to be
changed can be set to 0, otherwise the mask of channels to be changed,
and the rising and falling edge bitmasks are shifted by the base channel
number before calling `ni6527_set_edge_detection()` to change the
appropriate registers.  Unfortunately, the code is comparing the base
channel (shift amount) to the interrupt subdevice's number of channels
(1) instead of the digital input subdevice's number of channels (24).
Fix it by comparing to 32 because all shift amounts for an `unsigned
int` must be less than that and everything from bit 24 upwards is
ignored by `ni6527_set_edge_detection()` anyway.

Fixes: 110f9e687c1a8 ("staging: comedi: ni_6527: support INSN_CONFIG_DIGITAL_TRIG")
Cc:  # 3.17+
Signed-off-by: Ian Abbott 
Link: https://lore.kernel.org/r/20200717145257.112660-2-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman

staging: comedi: addi_apci_1032: check INSN_CONFIG_DIGITAL_TRIG shift

2020-07-29T08:18:42+00:00

commit 0bd0db42a030b75c20028c7ba6e327b9cb554116 upstream.

The `INSN_CONFIG` comedi instruction with sub-instruction code
`INSN_CONFIG_DIGITAL_TRIG` includes a base channel in `data[3]`. This is
used as a right shift amount for other bitmask values without being
checked.  Shift amounts greater than or equal to 32 will result in
undefined behavior.  Add code to deal with this.

Fixes: 33cdce6293dcc ("staging: comedi: addi_apci_1032: conform to new INSN_CONFIG_DIGITAL_TRIG")
Cc:  #3.8+
Signed-off-by: Ian Abbott 
Link: https://lore.kernel.org/r/20200717145257.112660-3-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman

staging: comedi: verify array index is correct before using it

2020-07-22T07:33:02+00:00

[ Upstream commit ef75e14a6c935eec82abac07ab68e388514e39bc ]

This code reads from the array before verifying that "trig" is a valid
index.  If the index is wildly out of bounds then reading from an
invalid address could lead to an Oops.

Fixes: a8c66b684efa ("staging: comedi: addi_apci_1500: rewrite the subdevice support functions")
Signed-off-by: Dan Carpenter 
Reviewed-by: Ian Abbott 
Link: https://lore.kernel.org/r/20200709102936.GA20875@mwanda
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Sasha Levin

staging: comedi: Fix comedi_device refcnt leak in comedi_open

2020-04-29T14:33:20+00:00

commit 332e0e17ad49e084b7db670ef43b5eb59abd9e34 upstream.

comedi_open() invokes comedi_dev_get_from_minor(), which returns a
reference of the COMEDI device to "dev" with increased refcount.

When comedi_open() returns, "dev" becomes invalid, so the refcount
should be decreased to keep refcount balanced.

The reference counting issue happens in one exception handling path of
comedi_open(). When "cfp" allocation is failed, the refcnt increased by
comedi_dev_get_from_minor() is not decreased, causing a refcnt leak.

Fix this issue by calling comedi_dev_put() on this error path when "cfp"
allocation is failed.

Fixes: 20f083c07565 ("staging: comedi: prepare support for per-file read and write subdevices")
Signed-off-by: Xiyu Yang 
Cc: stable 
Signed-off-by: Xin Tan 
Signed-off-by: Ian Abbott 
Link: https://lore.kernel.org/r/1587361459-83622-1-git-send-email-xiyuyang19@fudan.edu.cn
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Greg Kroah-Hartman

staging: comedi: dt2815: fix writing hi byte of analog output

2020-04-29T14:33:20+00:00

commit ed87d33ddbcd9a1c3b5ae87995da34e6f51a862c upstream.

The DT2815 analog output command is 16 bits wide, consisting of the
12-bit sample value in bits 15 to 4, the channel number in bits 3 to 1,
and a voltage or current selector in bit 0.  Both bytes of the 16-bit
command need to be written in turn to a single 8-bit data register.
However, the driver currently only writes the low 8-bits.  It is broken
and appears to have always been broken.

Electronic copies of the DT2815 User's Manual seem impossible to find
online, but looking at the source code, a best guess for the sequence
the driver intended to use to write the analog output command is as
follows:

1. Wait for the status register to read 0x00.
2. Write the low byte of the command to the data register.
3. Wait for the status register to read 0x80.
4. Write the high byte of the command to the data register.

Step 4 is missing from the driver.  Add step 4 to (hopefully) fix the
driver.

Also add a "FIXME" comment about setting bit 0 of the low byte of the
command.  Supposedly, it is used to choose between voltage output and
current output, but the current driver always sets it to 1.

Signed-off-by: Ian Abbott 
Cc: stable 
Link: https://lore.kernel.org/r/20200406142015.126982-1-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Greg Kroah-Hartman

staging: comedi: ni_routes: allow partial routing information

2020-01-23T07:22:35+00:00

commit 9fea3a40f6b07de977a2783270c8c3bc82544d45 upstream.

This patch fixes a regression on setting up asynchronous commands to use
external trigger sources when board-specific routing information is
missing.

`ni_find_device_routes()` (called via `ni_assign_device_routes()`) finds
the table of register values for the device family and the set of valid
routes for the specific board.  If both are found,
`tables->route_values` is set to point to the table of register values
for the device family and `tables->valid_routes` is set to point to the
list of valid routes for the specific board.  If either is not found,
both `tables->route_values` and `tables->valid_routes` are left set at
their initial null values (initialized by `ni_assign_device_routes()`)
and the function returns `-ENODATA`.

Returning an error results in some routing functionality being disabled.
Unfortunately, leaving `table->route_values` set to `NULL` also breaks
the setting up of asynchronous commands that are configured to use
external trigger sources.  Calls to `ni_check_trigger_arg()` or
`ni_check_trigger_arg_roffs()` while checking the asynchronous command
set-up would result in a null pointer dereference if
`table->route_values` is `NULL`.  The null pointer dereference is fixed
in another patch, but it now results in failure to set up the
asynchronous command.  That is a regression from the behavior prior to
commit 347e244884c3 ("staging: comedi: tio: implement global tio/ctr
routing") and commit 56d0b826d39f ("staging: comedi: ni_mio_common:
implement new routing for TRIG_EXT").

Change `ni_find_device_routes()` to set `tables->route_values` and/or
`tables->valid_routes` to valid information even if the other one can
only be set to `NULL` due to missing information.  The function will
still return an error in that case.  This should result in
`tables->valid_routes` being valid for all currently supported device
families even if the board-specific routing information is missing.
That should be enough to fix the regression on setting up asynchronous
commands to use external triggers for boards with missing routing
information.

Fixes: 347e244884c3 ("staging: comedi: tio: implement global tio/ctr routing")
Fixes: 56d0b826d39f ("staging: comedi: ni_mio_common: implement new routing for TRIG_EXT").
Cc:  # 4.20+
Cc: Spencer E. Olson 
Signed-off-by: Ian Abbott 
Link: https://lore.kernel.org/r/20200114182532.132058-3-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman