commit 5ca05345c56cb979e1a25ab6146437002f95cac8 upstream.

For counter subdevices, the `s->insn_write` handler is being set to the
wrong function, `ni_tio_insn_read()`.  It should be
`ni_tio_insn_write()`.

Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Reported-by: Éric Piel <piel@delmic.com>
Fixes: 10f74377eec3 ("staging: comedi: ni_tio: make ni_tio_winsn() a
  proper comedi (*insn_write)"
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit f0f4b0cc3a8cffd983f5940d46cd0227f3f5710a upstream.

Commit ebb657babfa9 ("staging: comedi: ni_mio_common: clarify the
cmd->start_arg validation and use") introduced a backwards compatibility
issue in the use of asynchronous commands on the AO subdevice when
`start_src` is `TRIG_EXT`.  Valid values for `start_src` are `TRIG_INT`
(for internal, software trigger), and `TRIG_EXT` (for external trigger).
When set to `TRIG_EXT`.  In both cases, the driver relies on an
internal, software trigger to set things up (allowing the user
application to write sufficient samples to the data buffer before the
trigger), so it acts as a software "pre-trigger" in the `TRIG_EXT` case.
The software trigger is handled by `ni_ao_inttrig()`.

Prior to the above change, when `start_src` was `TRIG_INT`, `start_arg`
was required to be 0, and `ni_ao_inttrig()` checked that the software
trigger number was also 0.  After the above change, when `start_src` was
`TRIG_INT`, any value was allowed for `start_arg`, and `ni_ao_inttrig()`
checked that the software trigger number matched this `start_arg` value.
The backwards compatibility issue is that the internal trigger number
now has to match `start_arg` when `start_src` is `TRIG_EXT` when it
previously had to be 0.

Fix the backwards compatibility issue in `ni_ao_inttrig()` by always
allowing software trigger number 0 when `start_src` is something other
than `TRIG_INT`.

Thanks to Spencer Olson for reporting the issue.

Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Reported-by: Spencer Olson <olsonse@umich.edu>
Fixes: ebb657babfa9 ("staging: comedi: ni_mio_common: clarify the cmd->start_arg validation and use")
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 403fe7f34e3327ddac2e06a15e76a293d613381e upstream.

Commit 73e0e4dfed4c ("staging: comedi: comedi_test: fix timer lock-up")
fixed a lock-up in the timer routine `waveform_ai_timer()` (which was
called `waveform_ai_interrupt()` at the time) caused by
commit 240512474424 ("staging: comedi: comedi_test: use
comedi_handle_events()").  However, it introduced a race condition that
can result in the timer routine misbehaving, such as accessing freed
memory or dereferencing a NULL pointer.

73e0... changed the timer routine to do nothing unless a
`WAVEFORM_AI_RUNNING` flag was set, and changed `waveform_ai_cancel()`
to clear the flag and replace a call to `del_timer_sync()` with a call
to `del_timer()`.  `waveform_ai_cancel()` may be called from the timer
routine itself (via `comedi_handle_events()`), or from `do_cancel()`.
(`do_cancel()` is called as a result of a file operation (usually a
`COMEDI_CANCEL` ioctl command, or a release), or during device removal.)
When called from `do_cancel()`, the call to `waveform_ai_cancel()` is
followed by a call to `do_become_nonbusy()`, which frees up stuff for
the current asynchronous command under the assumption that it is now
safe to do so.  The race condition occurs when the timer routine
`waveform_ai_timer()` checks the `WAVEFORM_AI_RUNNING` flag just before
it is cleared by `waveform_ai_cancel()`, and is still running during the
call to `do_become_nonbusy()`.  In particular, it can lead to a NULL
pointer dereference:

BUG: unable to handle kernel NULL pointer dereference at (null)
IP: [<ffffffffc0c63add>] waveform_ai_timer+0x17d/0x290 [comedi_test]

That corresponds to this line in `waveform_ai_timer()`:

		unsigned int chanspec = cmd->chanlist[async->cur_chan];

but `do_become_nonbusy()` frees `cmd->chanlist` and sets it to `NULL`.

Fix the race by calling `del_timer_sync()` instead of `del_timer()` in
`waveform_ai_cancel()` when not in an interrupt context.  The only time
`waveform_ai_cancel()` is called in an interrupt context is when it is
called from the timer routine itself, via `comedi_handle_events()`.

There is no longer any need for the `WAVEFORM_AI_RUNNING` flag, so get
rid of it.

The bug was copied from the AI subdevice to the AO when support for
commands on the AO subdevice was added by commit 0cf55bbef2f9 ("staging:
comedi: comedi_test: implement commands on AO subdevice").  That
involves the timer routine `waveform_ao_timer()`, the comedi "cancel"
routine `waveform_ao_cancel()`, and the flag `WAVEFORM_AO_RUNNING`.  Fix
it in the same way as for the AI subdevice.

Fixes: 73e0e4dfed4c ("staging: comedi: comedi_test: fix timer lock-up")
Fixes: 0cf55bbef2f9 ("staging: comedi: comedi_test: implement commands
 on AO subdevice")
Reported-by: Éric Piel <piel@delmic.com>
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Cc: Éric Piel <piel@delmic.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 80e162ee9b31d77d851b10f8c5299132be1e120f upstream.

`daqboard2000_find_boardinfo()` is supposed to check if the
DaqBoard/2000 series model is supported, based on the PCI subvendor and
subdevice ID.  The current code is wrong as it is comparing the PCI
device's subdevice ID to an expected, fixed value for the subvendor ID.
It should be comparing the PCI device's subvendor ID to this fixed
value.  Correct it.

Fixes: 7e8401b23e7f ("staging: comedi: daqboard2000: add back subsystem_device check")
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit d375278d666760e195693b57415ba0a125cadd55 upstream.

DMA is optional with this driver. If it was not enabled the devpriv->dma
pointer will be NULL.

Fix the possible NULL pointer dereference when trying to disable the DMA
channels in das1800_ai_cancel() and tidy up the comments to fix the
checkpatch.pl issues:
WARNING: line over 80 characters

It's probably harmless in das1800_ai_setup_dma() because the 'desc' pointer
will not be used if DMA is disabled but fix it there also.

Fixes: 99dfc3357e98 ("staging: comedi: das1800: remove depends on ISA_DMA_API limitation")
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit bd3a3cd6c27b117fb9a43a38c8072c95332beecc upstream.

Memory mapped io (dev->mmio) should not also be writing to the ioport
(dev->iobase) registers. Add the missing 'else' to these functions.

Fixes: 0953ee4acca0 ("staging: comedi: ni_mio_common: checkpatch.pl cleanup (else not useful)")
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 1fd24a4702d2af0ea4d5845126cf57d4d1796216 upstream.

This fixes a bug in function ni_tio_input_inttrig().  The trigger number
should be compared to cmd->start_arg, not cmd->start_src.

Fixes: 6a760394d7eb ("staging: comedi: ni_tiocmd: clarify the cmd->start_arg validation and use")
Signed-off-by: Spencer E. Olson <olsonse@umich.edu>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Implement COMEDI asynchronous commands on the fake analog output
subdevice.  This is useful for testing asynchronous commands in the
"write" direction when no real hardware is available.

A normal kernel timer is used to drive the command.  The new timer
expiry function `waveform_ao_timer()` handles whole "scans" at a time
according to the number of scan period that have elapsed since the last
scan.  Data for each channel in the scan is written to the internal
loopback array `devpriv->ao_loopbacks[]` and can be read back on the
analog input channels.  However, if several scan periods are outstanding
in the timer expiry function, only the latest available scan data is
written to the loopback array in order to save processing time.  The
expiry function also checks for underrun conditions, and checks for
normal termination of the asynchronous command when a "stop" scan count
is reached.

After the command is tested by `waveform_ao_cmdtest()` and set up by
`waveform_ao_cmd()`, it is not started until an internal trigger
function `waveform_ao_inttrig_start()` is called as a result of the user
performing an `INSN_INTTRIG` instruction on the subdevice.  The command
is stopped when the "cancel" handler `waveform_ao_cancel()` is called.
This may be due to the command terminating due to completion or an
error, or as a result of the user cancelling the command.

Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

`waveform_ai_interrupt()` is a timer expiry function used to generate
fake waveform data for an analog input subdevice.  Rename it to
`waveform_ai_timer()`.

Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

For asynchronous command handling on the analog input subdevice, a
kernel timer routine is used to generate the fake waveform data.  A
"scan" consists of a number of conversions separated in time by a
conversion period.  Successive scans are separated in time by a scan
period, which is at least the conversion period multiplied by the number
of conversions per scan.  Currently, the timer routine does not generate
any data until the end of a scan period, generating whole scans of data
at a time.  Change it to generate data at the end of each conversion
period, with an extra delay after the final conversion in each scan if
necessary.  Use new member `ai_convert_time` in the private data
structure `struct waveform_private` to keep track of when the next
conversion is due.  This replaces the old member `ai_last_scan_time`
which kept track of the time of the previous scan.

Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>