commit f20fbaad7620af2df36a1f9d1c9ecf48ead5b747 upstream.

`spidev_message()` sums the lengths of the individual SPI transfers to
determine the overall SPI message length.  It restricts the total
length, returning an error if too long, but it does not check for
arithmetic overflow.  For example, if the SPI message consisted of two
transfers and the first has a length of 10 and the second has a length
of (__u32)(-1), the total length would be seen as 9, even though the
second transfer is actually very long.  If the second transfer specifies
a null `rx_buf` and a non-null `tx_buf`, the `copy_from_user()` could
overrun the spidev's pre-allocated tx buffer before it reaches an
invalid user memory address.  Fix it by checking that neither the total
nor the individual transfer lengths exceed the maximum allowed value.

Thanks to Dan Carpenter for reporting the potential integer overflow.

Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit f511ab09dfb0fe7b2335eccac51ff9f001a32e4a upstream.

They are used to decide if the controller can do DMA on a buffer
of a specific length and thus are needed before any transfer is attempted.

This fixes a memory leak where the SPI core uses the drivers can_dma()
callback to determine if a buffer needs to be mapped. As the watermark
levels aren't correct at that point the driver falsely claims to be able to
DMA the buffer when it fact it isn't.
After the transfer has been done the core uses the same callback to
determine if it needs to unmap the buffers. As the driver now correctly
claims to not being able to DMA the buffer the core doesn't attempt to
unmap the buffer which leaves the SGT leaking.

Fixes: f62caccd12c17e4 (spi: spi-imx: add DMA support)
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

With spidev the mesg->complete callback points to spidev_complete.
Calling this unblocks spidev_sync and so spidev_sync_write finishes. As
the struct spi_message just read is a local variable in
spidev_sync_write and recording the trace event accesses this message
the recording is better done first. The same can happen for
spidev_sync_read.

This fixes an oops observed on a 3.14-rt system with spidev activity
after

	echo 1 > /sys/kernel/debug/tracing/events/spi/enable

.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org

The logic of DMA completion is broken now since test_and_clear_bit() never
returns the other bit is set. It means condition are always false and we have
spi_finalize_current_transfer() called per each DMA completion which is wrong.

The patch fixes logic by clearing BUSY bit first and then check for the other
one.

Fixes: 30c8eb52cc4a (spi: dw-mid: split rx and tx callbacks when DMA)
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org

num-cs is 32 bit property, don't read just upper 16 bits.

Fixes: 4a8573abe965 (spi: qup: Remove chip select function)
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org

Commit fd316941c ("spi/pl022: disable port when unused") introduced a race,
which leads to possible driver lock up (easily reproducible on SMP).

The problem happens in giveback() function where the completion of the transfer
is signalled to SPI subsystem and then the HW SPI controller is disabled. Another
transfer might be setup in between, which brings driver in locked-up state.

Exact event sequence on SMP:

core0                                   core1

                                        => pump_transfers()
                                        /* message->state == STATE_DONE */
                                          => giveback()
                                            => spi_finalize_current_message()

=> pl022_unprepare_transfer_hardware()
=> pl022_transfer_one_message
  => flush()
  => do_interrupt_dma_transfer()
    => set_up_next_transfer()
    /* Enable SSP, turn on interrupts */
    writew((readw(SSP_CR1(pl022->virtbase)) |
           SSP_CR1_MASK_SSE), SSP_CR1(pl022->virtbase));

...

=> pl022_interrupt_handler()
  => readwriter()

                                        /* disable the SPI/SSP operation */
                                        => writew((readw(SSP_CR1(pl022->virtbase)) &
                                                  (~SSP_CR1_MASK_SSE)), SSP_CR1(pl022->virtbase));

Lockup! SPI controller is disabled and the data will never be received. Whole
SPI subsystem is waiting for transfer ACK and blocked.

So, only signal transfer completion after disabling the controller.

Fixes: fd316941c (spi/pl022: disable port when unused)
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org

When DMA descriptor allocation fails we should not try to assign any fields in
the bad descriptor. The patch adds the necessary checks for that.

Fixes: 7063c0d942a1 (spi/dw_spi: add DMA support)
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org

Maximum transfer length supported by SPFI is 65535, this is limited
by the number of bits available in SPFI TSize register to represent
the transfer size.
For transfer requests larger than the maximum supported the driver
will return an invalid argument error.

Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Reviewed-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>