For "0" requirement which is used to inform firmware that device is
not required currently by master, Versal PLM (Platform Loader and
Manager) which runs on Platform Management Controller and is responsible
platform management of devices that disables clock, power it down
and reset the device. genpd_power_off() is being called during runtime
suspend also. So, if any device goes to runtime suspend state during
resumes it needs to be re-initialized again. It is possible that
drivers do not reinitialize device upon resume from runtime suspend
every time ans so dont want it to be powered down or get reset
during runtime suspend.

In Versal PLM new PM_CAP_UNUSABLE capability is added, which disables
clock only and avoids power down and reset during runtime suspend. Power
and reset will be gated with core suspend.So, this patch sets
CAPABILITY_UNUSABLE requirement during gpd_power_off()
if platform is other than zynqmp.

Signed-off-by: Tejas Patel <tejas.patel@xilinx.com>
Signed-off-by: Jolly Shah <jolly.shah@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Driver needs ZynqMP firmware interface to call EEMI
APIs. In case firmware is not ready, dependent drivers
should wait until the firmware is ready.

Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Signed-off-by: Jolly Shah <jollys@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

The zynqmp-genpd driver communicates the usage requirements
for logical power domains / devices to the platform FW.
FW is responsible for choosing appropriate power states,
taking Linux' usage information into account.

Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Signed-off-by: Jolly Shah <jolly.shah@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Add ZynqMP PM driver. PM driver provides power management
support for ZynqMP.

Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Signed-off-by: Jolly Shah <jolly.shah@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Tabs should be used for alignment instead of spaces.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Currently clkoutdiv is being operated on by a logical && operator rather
than a bitwise & operator. This looks incorrect as these should be bit
flag operations.

Addresses-Coverity-ID: 1463959 ("Logical vs. bitwise operator")
Fixes: cee8113a295a ("soc: xilinx: xlnx_vcu: Add Xilinx ZYNQMP VCU logicoreIP init driver")
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Acked-by: Dhaval Shah <dshah@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

xlnx_vcu driver uses devm_ioremap_nocache, which is included
only when HAS_IOMEM is enabled.

drivers/soc/xilinx/xlnx_vcu.o: In function `xvcu_probe':
   xlnx_vcu.c:(.text+0x116): undefined reference to `devm_ioremap_nocache'
   xlnx_vcu.c:(.text+0x1ae): undefined reference to `devm_ioremap_nocache'

Signed-off-by: Dhaval Shah <dshah@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Xilinx ZYNQMP logicoreIP Init driver is based on the new
LogiCoreIP design created. This driver provides the processing system
and programmable logic isolation. Set the frequency based on the clock
information get from the logicoreIP register set.

Signed-off-by: Dhaval Shah <dshah@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Create directory structure with Makefile/Kconfig for adding xilinx soc
specific drivers.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>