linux-stable.git/drivers/soc/qcom, branch linux-4.17.y

soc: qcom: smem: byte swap values properly

2018-08-03T05:47:44+00:00

[ Upstream commit 04a512fea333369cc0b550f3b90df0d638e34d00 ]

Two places report an error when a partition header is found to
not contain the right canary value.  The error messages do not
properly byte swap the host ids.  Fix this, and adjust the format
specificier to match the 16-bit unsigned data type.

Move the error handling for a bad canary value to the end of
qcom_smem_alloc_private().  This avoids some long lines, and
reduces the distraction of handling this unexpected problem.

Signed-off-by: Alex Elder 
Reviewed-by: Bjorn Andersson 
Signed-off-by: Andy Gross 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman

soc: qcom: smem: fix qcom_smem_set_global_partition()

2018-08-03T05:47:44+00:00

[ Upstream commit 8fa1a21409da6abfe890f66532f9fcd8d2c25a3d ]

If there is at least one entry in the partition table, but no global
entry, the qcom_smem_set_global_partition() should return an error
just like it does if there are no partition table entries.

It turns out the function still returns an error in this case, but
it waits to do so until it has mistakenly treated the last entry in
the table as if it were the global entry found.

Fix the function to return immediately if no global entry is found
in the table.

Signed-off-by: Alex Elder 
Reviewed-by: Bjorn Andersson 
Signed-off-by: Andy Gross 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman

soc: qcom: qmi: fix a buffer sizing bug

2018-08-03T05:47:43+00:00

[ Upstream commit 7df5ff258bd27900d516fea88da10d05602bf8c7 ]

In qmi_handle_init(), a buffer is allocated for to hold messages
received through the handle's socket.  Any "normal" messages
(expected by the caller) will have a header prepended, so the
buffer size is adjusted to accomodate that.

The buffer must also be of sufficient size to receive control
messages, so the size is increased if necessary to ensure these
will fit.

Unfortunately the calculation is done wrong, making it possible
for the calculated buffer size to be too small to hold a "normal"
message.  Specifically, if:

  recv_buf_size > sizeof(struct qrtr_ctrl_pkt) - sizeof(struct qmi_header)
		AND
  recv_buf_size < sizeof(struct qrtr_ctrl_pkt)

the current logic will use sizeof(struct qrtr_ctrl_pkt) as the
receive buffer size, which is not enough to hold the maximum
"normal" message plus its header.  Currently this problem occurs
for (13 < recv_buf_size < 20).

This patch corrects this.

Signed-off-by: Alex Elder 
Reviewed-by: Bjorn Andersson 
Signed-off-by: Andy Gross 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman

Merge tag 'rproc-v4.17' of git://github.com/andersson/remoteproc

2018-04-10T19:09:27+00:00

Pull remoteproc updates from Bjorn Andersson:

 - add support for generating coredumps for remoteprocs using
   devcoredump

 - add the Qualcomm sysmon driver for intra-remoteproc crash handling

 - a number of fixes in Qualcomm and IMX drivers

* tag 'rproc-v4.17' of git://github.com/andersson/remoteproc:
  remoteproc: fix null pointer dereference on glink only platforms
  soc: qcom: qmi: add CONFIG_NET dependency
  remoteproc: imx_rproc: Slightly simplify code in 'imx_rproc_probe()'
  remoteproc: imx_rproc: Re-use existing error handling path in 'imx_rproc_probe()'
  remoteproc: imx_rproc: Fix an error handling path in 'imx_rproc_probe()'
  samples: Introduce Qualcomm QMI sample client
  remoteproc: qcom: Introduce sysmon
  remoteproc: Pass type of shutdown to subdev remove
  remoteproc: qcom: Register segments for core dump
  soc: qcom: mdt-loader: Return relocation base
  remoteproc: Rename "load_rsc_table" to "parse_fw"
  remoteproc: Add remote processor coredump support
  remoteproc: Remove null character write of shared mem

Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

2018-04-06T04:29:35+00:00

Pull ARM SoC driver updates from Arnd Bergmann:
 "The main addition this time around is the new ARM "SCMI" framework,
  which is the latest in a series of standards coming from ARM to do
  power management in a platform independent way.

  This has been through many review cycles, and it relies on a rather
  interesting way of using the mailbox subsystem, but in the end I
  agreed that Sudeep's version was the best we could do after all.

  Other changes include:

   - the ARM CCN driver is moved out of drivers/bus into drivers/perf,
     which makes more sense. Similarly, the performance monitoring
     portion of the CCI driver are moved the same way and cleaned up a
     little more.

   - a series of updates to the SCPI framework

   - support for the Mediatek mt7623a SoC in drivers/soc

   - support for additional NVIDIA Tegra hardware in drivers/soc

   - a new reset driver for Socionext Uniphier

   - lesser bug fixes in drivers/soc, drivers/tee, drivers/memory, and
     drivers/firmware and drivers/reset across platforms"

* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (87 commits)
  reset: uniphier: add ethernet reset control support for PXs3
  reset: stm32mp1: Enable stm32mp1 reset driver
  dt-bindings: reset: add STM32MP1 resets
  reset: uniphier: add Pro4/Pro5/PXs2 audio systems reset control
  reset: imx7: add 'depends on HAS_IOMEM' to fix unmet dependency
  reset: modify the way reset lookup works for board files
  reset: add support for non-DT systems
  clk: scmi: use devm_of_clk_add_hw_provider() API and drop scmi_clocks_remove
  firmware: arm_scmi: prevent accessing rate_discrete uninitialized
  hwmon: (scmi) return -EINVAL when sensor information is unavailable
  amlogic: meson-gx-socinfo: Update soc ids
  soc/tegra: pmc: Use the new reset APIs to manage reset controllers
  soc: mediatek: update power domain data of MT2712
  dt-bindings: soc: update MT2712 power dt-bindings
  cpufreq: scmi: add thermal dependency
  soc: mediatek: fix the mistaken pointer accessed when subdomains are added
  soc: mediatek: add SCPSYS power domain driver for MediaTek MT7623A SoC
  soc: mediatek: avoid hardcoded value with bus_prot_mask
  dt-bindings: soc: add header files required for MT7623A SCPSYS dt-binding
  dt-bindings: soc: add SCPSYS binding for MT7623 and MT7623A SoC
  ...

soc: qcom: qmi: add CONFIG_NET dependency

2018-03-27T20:43:29+00:00

Access to the socket API and the root network namespace is only available
when networking is enabled:

ERROR: "kernel_sendmsg" [drivers/soc/qcom/qmi_helpers.ko] undefined!
ERROR: "sock_release" [drivers/soc/qcom/qmi_helpers.ko] undefined!
ERROR: "sock_create_kern" [drivers/soc/qcom/qmi_helpers.ko] undefined!
ERROR: "kernel_getsockname" [drivers/soc/qcom/qmi_helpers.ko] undefined!
ERROR: "init_net" [drivers/soc/qcom/qmi_helpers.ko] undefined!
ERROR: "kernel_recvmsg" [drivers/soc/qcom/qmi_helpers.ko] undefined!

Adding a dependency on CONFIG_NET lets us build it in all randconfig
builds.

Fixes: 9b8a11e82615 ("soc: qcom: Introduce QMI encoder/decoder")
Acked-by: Andy Gross 
Signed-off-by: Arnd Bergmann 
Signed-off-by: Bjorn Andersson

soc: qcom: wcnss_ctrl: Fix increment in NV upload

2018-03-09T00:40:35+00:00

hdr.len includes both the size of the header and the fragment, so using
this when stepping through the firmware causes us to skip 16 bytes every
chunk of 3072 bytes; causing only the first fragment to actually be
valid data.

Instead use fragment size steps through the firmware blob.

Fixes: ea7a1f275cf0 ("soc: qcom: Introduce WCNSS_CTRL SMD client")
Reported-by: Will Newton 
Signed-off-by: Bjorn Andersson 
Signed-off-by: Andy Gross

soc: qcom: rmtfs-mem: Add support for assigning memory to remote

2018-03-09T00:40:24+00:00

On some platform the remote processor's memory map is not statically
configured in TrustZone, so each memory region that is to be accessed by
the remote needs a call into TrustZone to set up the remote's
permissions.

Implement this for the rmtfs memory driver, to give the modem on 8996
access to the shared file system buffers.

Signed-off-by: Bjorn Andersson 
Signed-off-by: Andy Gross

net: make getname() functions return length rather than use int* parameter

2018-02-12T19:15:04+00:00

Changes since v1:
Added changes in these files:
    drivers/infiniband/hw/usnic/usnic_transport.c
    drivers/staging/lustre/lnet/lnet/lib-socket.c
    drivers/target/iscsi/iscsi_target_login.c
    drivers/vhost/net.c
    fs/dlm/lowcomms.c
    fs/ocfs2/cluster/tcp.c
    security/tomoyo/network.c

Before:
All these functions either return a negative error indicator,
or store length of sockaddr into "int *socklen" parameter
and return zero on success.

"int *socklen" parameter is awkward. For example, if caller does not
care, it still needs to provide on-stack storage for the value
it does not need.

None of the many FOO_getname() functions of various protocols
ever used old value of *socklen. They always just overwrite it.

This change drops this parameter, and makes all these functions, on success,
return length of sockaddr. It's always >= 0 and can be differentiated
from an error.

Tests in callers are changed from "if (err)" to "if (err < 0)", where needed.

rpc_sockname() lost "int buflen" parameter, since its only use was
to be passed to kernel_getsockname() as &buflen and subsequently
not used in any way.

Userspace API is not changed.

    text    data     bss      dec     hex filename
30108430 2633624  873672 33615726 200ef6e vmlinux.before.o
30108109 2633612  873672 33615393 200ee21 vmlinux.o

Signed-off-by: Denys Vlasenko 
CC: David S. Miller 
CC: linux-kernel@vger.kernel.org
CC: netdev@vger.kernel.org
CC: linux-bluetooth@vger.kernel.org
CC: linux-decnet-user@lists.sourceforge.net
CC: linux-wireless@vger.kernel.org
CC: linux-rdma@vger.kernel.org
CC: linux-sctp@vger.kernel.org
CC: linux-nfs@vger.kernel.org
CC: linux-x25@vger.kernel.org
Signed-off-by: David S. Miller

soc: qcom: mdt-loader: Return relocation base

2018-02-12T19:05:38+00:00

In order to implement support for grabbing core dumps in remoteproc it's
necessary to know the relocated base of the image, as the offsets from
the virtual memory base might not be based on the physical address.

Return the adjusted physical base address to the caller.

Acked-by: Andy Gross 
Signed-off-by: Bjorn Andersson