Merge "Ux500 cleanups from Arnd" from Linus Walleij:

This is a set of cleanups for the Ux500 that reduce the number
of machine-local files and boardfile-type data for regulators
and ASoC.

* tag 'ux500-cleanup-bundle' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
  ARM: ux500: consolidate base platform files
  ARM: ux500: move soc_id driver to drivers/soc
  ARM: ux500: call ux500_setup_id later
  ARM: ux500: consolidate soc_device code in id.c
  ARM: ux500: remove cpu_is_u* helpers
  ARM: ux500: use CLK_OF_DECLARE()
  ARM: ux500: move l2x0 init to .init_irq
  mfd: db8500 stop passing around platform data
  ASoC: ab8500-codec: remove platform data based probe
  ARM: ux500: move ab8500_regulator_plat_data into driver
  ARM: ux500: remove unused regulator data

As the ux500 id code is basically a standalone driver, we can move it
out of the arch code into drivers/soc/ux500.

This is a user-visible change, as it moves all the devices in sysfs
from /sys/devices/soc0/ to /sys/devices/ and leaves the soc0 node as a
separate device.

Originally the idea was to put all on-chip devices under the soc node,
and ux500 was the first platform to have this device, but later platforms
almost all didn't follow that pattern, so this makes the platform do
the same thing as everyone else.

Since the platform is really obsolete now, I am optimistic that nothing
will break after moving the devices around.

As the SoC driver no longer has access to the private header files,
I'm changing the code to instead look up the address of the backupram
from devicetree, which is a good idea anyway.

Finally, having a separate Kconfig symbol means the driver is now
optional and could even be a loadable module rather than always being
built-in if we allowed that for soc_device.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[Fixup mising Makefile, fixup BB_UID_BASE to fc0]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Unify the different Broadcom SoCs directory and have everybody live
under drivers/soc/bcm/*.

Acked-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

Move the pm-rcar driver from arch/arm/mach-shmobile/ to
drivers/soc/renesas/, and its header file to include/linux/soc/renesas/,
so it can be shared between arm32 (R-Car H1 and Gen2) and arm64 (R-Car
Gen3). Rename it to rcar-sysc as it's really a driver for the R-Car
System Controller (SYSC).

Kill the intermediate PM_RCAR config symbol, as it's not user
configurable anymore, and to prepare for SoC-specific make rules.

Add the missing #include <linux/types.h> to rcar-sysc.h, which was
exposed by different include order.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

This patch moves Exynos PMU driver implementation from "arm/mach-exynos"
to "drivers/soc/samsung". This driver is mainly used for setting misc
bits of register from PMU IP of Exynos SoC which will be required to
configure before Suspend/Resume. Currently all these settings are done
in "arch/arm/mach-exynos/pmu.c" but moving ahead for ARM64 based SoC
support, there is a need of this PMU driver in driver/* folder.

This driver uses existing DT binding information and there should
be no functionality change in the supported platforms.

Signed-off-by: Amit Daniel Kachhap <amitdanielk@gmail.com>
[tested on Peach-Pi (Exynos5880)]
Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
[for testing on Trats2 (Exynos4412) and Odroid XU3 (Exynos5422)]
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
[k.kozlowski: Rebased, add necessary infrastructure for building and
selecting drivers/soc because original patchset was on top of movement
SROMc to drivers/soc]
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>

Pull ARM SoC driver updates from Olof Johansson:
 "Driver updates for ARM SoCs.  Some for SoC-family code under
  drivers/soc, but also some other driver updates that don't belong
  anywhere else.  We also bring in the drivers/reset code through
  arm-soc.

  Some of the larger updates:

   - Qualcomm support for SMEM, SMSM, SMP2P.  All used to communicate
     with other parts of the chip/board on these platforms, all
     proprietary protocols that don't fit into other subsystems and live
     in drivers/soc for now.

   - System bus driver for UniPhier

   - Driver for the TI Wakeup M3 IPC device

   - Power management for Raspberry PI

  + Again a bunch of other smaller updates and patches"

* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (38 commits)
  bus: uniphier: allow only built-in driver
  ARM: bcm2835: clarify RASPBERRYPI_FIRMWARE dependency
  MAINTAINERS: Drop Kumar Gala from QCOM
  bus: uniphier-system-bus: add UniPhier System Bus driver
  ARM: bcm2835: add rpi power domain driver
  dt-bindings: add rpi power domain driver bindings
  ARM: bcm2835: Define two new packets from the latest firmware.
  drivers/soc: make mediatek/mtk-scpsys.c explicitly non-modular
  soc: mediatek: SCPSYS: Add regulator support
  MAINTAINERS: Change QCOM entries
  soc: qcom: smd-rpm: Add existing platform support
  memory/tegra: Add number of TLB lines for Tegra124
  reset: hi6220: fix modular build
  soc: qcom: Introduce WCNSS_CTRL SMD client
  ARM: qcom: select ARM_CPU_SUSPEND for power management
  MAINTAINERS: Add rules for Qualcomm dts files
  soc: qcom: enable smsm/smp2p modular build
  serial: msm_serial: Make config tristate
  soc: qcom: smp2p: Qualcomm Shared Memory Point to Point
  soc: qcom: smsm: Add driver for Qualcomm SMSM
  ...

Pull ARM SoC multiplatform code updates from Arnd Bergmann:
 "This branch is the culmination of 5 years of effort to bring the ARMv6
  and ARMv7 platforms together such that they can all be enabled and
  boot the same kernel.  It has been a tremendous amount of cleanup and
  refactoring by a huge number of people, and creation of several new
  (and major) subsystems to better abstract out all the platform details
  in an appropriate manner.

  The bulk of this branch is a large patchset from Arnd that brings
  several of the more minor and older platforms we have closer to
  multiplatform support.  Among these are MMP, S3C64xx, Orion5x, mv78xx0
  and realview Much of this is moving around header files from old mach
  directories, but there are also some cleanup patches of debug_ll
  (lowlevel debug per-platform options) and other parts.

  Linus Walleij also has some patchs to clean up the older ARM Realview
  platforms by finally introducing DT support, and Rob Herring has some
  for ARM Versatile which is now DT-only.  Both of these platforms are
  now multiplatform.

  Finally, a couple of patches from Russell for Dove PMU, and a fix from
  Valentin Rothberg for Exynos ADC, which were rebased on top of the
  series to avoid conflicts"

* tag 'armsoc-multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (75 commits)
  ARM: realview: don't select SMP_ON_UP for UP builds
  ARM: s3c: simplify s3c_irqwake_{e,}intallow definition
  ARM: s3c64xx: fix pm-debug compilation
  iio: exynos-adc: fix irqf_oneshot.cocci warnings
  ARM: realview: build realview-dt SMP support only when used
  ARM: realview: select apropriate targets
  ARM: realview: clean up header files
  ARM: realview: make all header files local
  ARM: no longer make CPU targets visible separately
  ARM: integrator: use explicit core module options
  ARM: realview: enable multiplatform
  ARM: make default platform work for NOMMU
  ARM: debug-ll: move DEBUG_LL_UART_EFM32 to correct Kconfig location
  ARM: defconfig: use correct debug_ll settings
  ARM: versatile: convert to multi-platform
  ARM: versatile: merge mach code into a single file
  ARM: versatile: switch to DT only booting and remove legacy code
  ARM: versatile: add DT based PCI detection
  ARM: pxa: mark ezx structures as __maybe_unused
  ARM: pxa: mark raumfeld init functions as __maybe_unused
  ...

ls1 has qe and ls1 has arm cpu.
move qe from arch/powerpc to drivers/soc/fsl
to adapt to powerpc and arm

Signed-off-by: Zhao Qiang <qiang.zhao@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>

This patch adds support for several power domains on Raspberry Pi,
including USB (so it can be enabled even if the bootloader didn't do
it), and graphics.

This patch is the combined work of Eric Anholt (who wrote USB support
inside of the Raspberry Pi firmware driver, and wrote the non-USB
domain support) and Alexander Aring (who separated the original USB
work out from the firmware driver).

Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Kevin Hilman <khilman@linaro.org>

Add support for legacy non-DT Dove to the PMU driver, so that we can
transition the legacy support over.

[gregory.clement@free-electrons.com: removed pm_genpd_poweroff_unused]
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>