Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com> Signed-off-by: James Smart <james.smart@emulex.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Add Basic support for SLI4 Loopback. (CR 124951, 125766, 124951, 125843, 125832, 125843) - Added missing protection in setting/clearing of phba->link_flag bit field (CR 125994) - Use link type and link number obtained from READ_CONFIG mailbox command. (CR 126264) Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com> Signed-off-by: James Smart <james.smart@emulex.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Make lpfc_sli4_pci_mem_unset interface type aware (CR 124390) - Convert byte count to word count when calling __iowrite32_copy (CR 122550) - Checked the ERR1 and ERR2 registers for error attention due to SLI Port state affected by forced debug dump. (CR 122986, 122426, 124859) - Use the lpfc_readl routine instead of the readl for the port status register read in lpfc_handle_eratt_s4 (CR 125403) - Call lpfc_sli4_queue_destroy inside of lpfc_sli4_brdreset before doing a pci function reset (CR 125124, 125168, 125572, 125622) - Zero out the HBQ when it is allocated (CR 125663) - Alter port reset log messages to indicate error type (CR 125989) - Added proper NULL pointer checking to all the places that accessing the queue memory (CR 125832) Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com> Signed-off-by: James Smart <james.smart@emulex.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
FC and SCSI Discovery Fixes: - Clear the virtual fabrics bit (word 1 bit 30) when sending the FLOGI and FDISC. (CR 124339) - Return a MLQUEUE_DEVICE_BUSY if the driver detects that an I/O is being retried too quickly (CR 124668) - Remove NDLP reference put in lpfc_cmpl_els_logo_acc for all but fabric nodes (CR 123924) - Only retry FDISCs every second and stop retrying after devloss number of retries (CR 13939) - Check to see if vports are unloading before adding them to the vport work array. (CR 124996) - Fixed illegal state transition during driver unload (CR 124191) - Added missing protection on setting/clearing of vport->fc_flag bit (CR 126002) - Set NPIV flag in lpfc_mbx_process_link_up for all ports sli3 and above. (CR 126094) - Clear FCP command bytes that are not used. (CR 126209) Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com> Signed-off-by: James Smart <james.smart@emulex.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Add support for ABTS failure handling: - Add asynchronous ABTS notification event feature to driver (CR 124578) - Change driver message 3092 and 3116 to KERN_WARNING (CR 124768) - Alter the SCR ELS command to use the temporary RPI and the Destination DID for SLI4-FC (CR 126070) Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com> Signed-off-by: James Smart <james.smart@emulex.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Adapter (SLI) interface fixes: - Modify WQ handling to use entry_repost (CR 123981) - Fix for ABTS. Do not free original IOCB whenever ABTS fails. (CR 115829) - Check board for FCoE before reading FCoE paramaters (CR124731) - Add support for SLI4 FC Loop mode (CR 124721) - Add support for resource count changes during fw reset. (CR 125888, 125675) - Increase CQE count from 256 to 1024. (CR 126149) Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com> Signed-off-by: James Smart <james.smart@emulex.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Miscellaneous fixes in sysfs and mgmt interfaces: - Added SLI4 INTF_TYPE and SLI_FAMILY as sub-field to the fwrev sysfs attribute (CR 124103) - Added a sysfs attribute "protocol" to report SLI4 port link protocol type (CR 124102) - Increment mix-and-match minor number by 1 for added "protocol" sysfs attribute. (124102) - Move the link speed check into the generic sli3/sli4 code path. (CR 124185, 124122) - Deleted check for inExtWLen (CR 122523) - Add the word "offline" to message 2889 (CR 124385) - Conditionalize the firmware upgrade/downgrade so that it is only attempted for SLI4 type 2 boards (CR 124406) - Return an error if the mbox sysfs is called. (CR 124210) - When port_state is less than LPFC_VPORT_READY, report FC_PORTSTATE_BYPASSED (CR 120018) - Added driver support for performing persistent linkdown based on configure region 23 (CR 124534) - Added restore state and error log when sysfs board_mode attribute access failed (CR 124158) - Added support for SLI4_CONFIG non-embedded COMN_GET_CNTL_ADDL_ATTR pass-through (CR 124466) - Rejecting un-supported multi-buffer mailbox commands (CR 124771) - Byte swap the extended data request and response data for extended mailbox data (CR 125081) Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com> Signed-off-by: James Smart <james.smart@emulex.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The module.h header was implicitly present everywhere, so files with no explicit include of the module infrastructure would build anyway. We are now removing the implicit include, and so we need to call out the module.h file that we need explicitly. Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
For the basic SCSI infrastructure files that are exporting symbols but not modules themselves, add in the basic export.h header file to allow the exports. Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Change driver version to 8.3.27 Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com> Signed-off-by: James Smart <james.smart@emulex.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>