linux-stable.git/drivers/s390, branch v3.16.78

s390/dasd: fix endless loop after read unit address configuration

2019-11-22T15:57:10+00:00

commit 41995342b40c418a47603e1321256d2c4a2ed0fb upstream.

After getting a storage server event that causes the DASD device driver
to update its unit address configuration during a device shutdown there is
the possibility of an endless loop in the device driver.

In the system log there will be ongoing DASD error messages with RC: -19.

The reason is that the loop starting the ruac request only terminates when
the retry counter is decreased to 0. But in the sleep_on function there are
early exit paths that do not decrease the retry counter.

Prevent an endless loop by handling those cases separately.

Remove the unnecessary do..while loop since the sleep_on function takes
care of retries by itself.

Fixes: 8e09f21574ea ("[S390] dasd: add hyper PAV support to DASD device driver, part 1")
Signed-off-by: Stefan Haberland 
Reviewed-by: Jan Hoeppner 
Signed-off-by: Jens Axboe 
Signed-off-by: Ben Hutchings

s390/qdio: don't touch the dsci in tiqdio_add_input_queues()

2019-10-31T22:15:01+00:00

commit ac6639cd3db607d386616487902b4cc1850a7be5 upstream.

Current code sets the dsci to 0x00000080. Which doesn't make any sense,
as the indicator area is located in the _left-most_ byte.

Worse: if the dsci is the _shared_ indicator, this potentially clears
the indication of activity for a _different_ device.
tiqdio_thinint_handler() will then have no reason to call that device's
IRQ handler, and the device ends up stalling.

Fixes: d0c9d4a89fff ("[S390] qdio: set correct bit in dsci")
Signed-off-by: Julian Wiedmann 
Signed-off-by: Vasily Gorbik 
Signed-off-by: Ben Hutchings

s390/qdio: (re-)initialize tiqdio list entries

2019-10-31T22:15:00+00:00

commit e54e4785cb5cb4896cf4285964aeef2125612fb2 upstream.

When tiqdio_remove_input_queues() removes a queue from the tiq_list as
part of qdio_shutdown(), it doesn't re-initialize the queue's list entry
and the prev/next pointers go stale.

If a subsequent qdio_establish() fails while sending the ESTABLISH cmd,
it calls qdio_shutdown() again in QDIO_IRQ_STATE_ERR state and
tiqdio_remove_input_queues() will attempt to remove the queue entry a
second time. This dereferences the stale pointers, and bad things ensue.
Fix this by re-initializing the list entry after removing it from the
list.

For good practice also initialize the list entry when the queue is first
allocated, and remove the quirky checks that papered over this omission.
Note that prior to
commit e521813468f7 ("s390/qdio: fix access to uninitialized qdio_q fields"),
these checks were bogus anyway.

setup_queues_misc() clears the whole queue struct, and thus needs to
re-init the prev/next pointers as well.

Fixes: 779e6e1c724d ("[S390] qdio: new qdio driver.")
Signed-off-by: Julian Wiedmann 
Signed-off-by: Vasily Gorbik 
Signed-off-by: Ben Hutchings

s390/qdio: handle PENDING state for QEBSM devices

2019-10-31T22:14:52+00:00

commit 04310324c6f482921c071444833e70fe861b73d9 upstream.

When a CQ-enabled device uses QEBSM for SBAL state inspection,
get_buf_states() can return the PENDING state for an Output Queue.
get_outbound_buffer_frontier() isn't prepared for this, and any PENDING
buffer will permanently stall all further completion processing on this
Queue.

This isn't a concern for non-QEBSM devices, as get_buf_states() for such
devices will manually turn PENDING buffers into EMPTY ones.

Fixes: 104ea556ee7f ("qdio: support asynchronous delivery of storage blocks")
Signed-off-by: Julian Wiedmann 
Signed-off-by: Heiko Carstens 
Signed-off-by: Ben Hutchings

s390/qeth: fix VLAN attribute in bridge_hostnotify udev event

2019-10-05T15:19:52+00:00

commit 335726195e460cb6b3f795b695bfd31f0ea70ef0 upstream.

Enabling sysfs attribute bridge_hostnotify triggers a series of udev events
for the MAC addresses of all currently connected peers. In case no VLAN is
set for a peer, the device reports the corresponding MAC addresses with
VLAN ID 4096. This currently results in attribute VLAN=4096 for all
non-VLAN interfaces in the initial series of events after host-notify is
enabled.

Instead, no VLAN attribute should be reported in the udev event for
non-VLAN interfaces.

Only the initial events face this issue. For dynamic changes that are
reported later, the device uses a validity flag.

This also changes the code so that it now sets the VLAN attribute for
MAC addresses with VID 0. On Linux, no qeth interface will ever be
registered with VID 0: Linux kernel registers VID 0 on all network
interfaces initially, but qeth will drop .ndo_vlan_rx_add_vid for VID 0.
Peers with other OSs could register MACs with VID 0.

Fixes: 9f48b9db9a22 ("qeth: bridgeport support - address notifications")
Signed-off-by: Alexandra Winter 
Signed-off-by: Julian Wiedmann 
Signed-off-by: David S. Miller 
Signed-off-by: Ben Hutchings

scsi: zfcp: fix to prevent port_remove with pure auto scan LUNs (only sdevs)

2019-10-05T15:19:50+00:00

commit ef4021fe5fd77ced0323cede27979d80a56211ca upstream.

When the user tries to remove a zfcp port via sysfs, we only rejected it if
there are zfcp unit children under the port. With purely automatically
scanned LUNs there are no zfcp units but only SCSI devices. In such cases,
the port_remove erroneously continued. We close the port and this
implicitly closes all LUNs under the port. The SCSI devices survive with
their private zfcp_scsi_dev still holding a reference to the "removed"
zfcp_port (still allocated but invisible in sysfs) [zfcp_get_port_by_wwpn
in zfcp_scsi_slave_alloc]. This is not a problem as long as the fc_rport
stays blocked. Once (auto) port scan brings back the removed port, we
unblock its fc_rport again by design.  However, there is no mechanism that
would recover (open) the LUNs under the port (no "ersfs_3" without
zfcp_unit [zfcp_erp_strategy_followup_success]).  Any pending or new I/O to
such LUN leads to repeated:

  Done: NEEDS_RETRY Result: hostbyte=DID_IMM_RETRY driverbyte=DRIVER_OK

See also v4.10 commit 6f2ce1c6af37 ("scsi: zfcp: fix rport unblock race
with LUN recovery"). Even a manual LUN recovery
(echo 0 > /sys/bus/scsi/devices/H:C:T:L/zfcp_failed)
does not help, as the LUN links to the old "removed" port which remains
to lack ZFCP_STATUS_COMMON_RUNNING [zfcp_erp_required_act].
The only workaround is to first ensure that the fc_rport is blocked
(e.g. port_remove again in case it was re-discovered by (auto) port scan),
then delete the SCSI devices, and finally re-discover by (auto) port scan.
The port scan includes an fc_rport unblock, which in turn triggers
a new scan on the scsi target to freshly get new pure auto scan LUNs.

Fix this by rejecting port_remove also if there are SCSI devices
(even without any zfcp_unit) under this port. Re-use mechanics from v3.7
commit d99b601b6338 ("[SCSI] zfcp: restore refcount check on port_remove").
However, we have to give up zfcp_sysfs_port_units_mutex earlier in unit_add
to prevent a deadlock with scsi_host scan taking shost->scan_mutex first
and then zfcp_sysfs_port_units_mutex now in our zfcp_scsi_slave_alloc().

Signed-off-by: Steffen Maier 
Fixes: b62a8d9b45b9 ("[SCSI] zfcp: Use SCSI device data zfcp scsi dev instead of zfcp unit")
Fixes: f8210e34887e ("[SCSI] zfcp: Allow midlayer to scan for LUNs when running in NPIV mode")
Reviewed-by: Benjamin Block 
Signed-off-by: Martin K. Petersen 
Signed-off-by: Ben Hutchings

scsi: zfcp: fix missing zfcp_port reference put on -EBUSY from port_remove

2019-10-05T15:19:49+00:00

commit d27e5e07f9c49bf2a6a4ef254ce531c1b4fb5a38 upstream.

With this early return due to zfcp_unit child(ren), we don't use the
zfcp_port reference from the earlier zfcp_get_port_by_wwpn() anymore and
need to put it.

Signed-off-by: Steffen Maier 
Fixes: d99b601b6338 ("[SCSI] zfcp: restore refcount check on port_remove")
Reviewed-by: Jens Remus 
Reviewed-by: Benjamin Block 
Signed-off-by: Martin K. Petersen 
Signed-off-by: Ben Hutchings

scsi: zfcp: fix scsi_eh host reset with port_forced ERP for non-NPIV FCP devices

2019-08-13T11:38:55+00:00

commit 242ec1455151267fe35a0834aa9038e4c4670884 upstream.

Suppose more than one non-NPIV FCP device is active on the same channel.
Send I/O to storage and have some of the pending I/O run into a SCSI
command timeout, e.g. due to bit errors on the fibre. Now the error
situation stops. However, we saw FCP requests continue to timeout in the
channel. The abort will be successful, but the subsequent TUR fails.
Scsi_eh starts. The LUN reset fails. The target reset fails.  The host
reset only did an FCP device recovery. However, for non-NPIV FCP devices,
this does not close and reopen ports on the SAN-side if other non-NPIV FCP
device(s) share the same open ports.

In order to resolve the continuing FCP request timeouts, we need to
explicitly close and reopen ports on the SAN-side.

This was missing since the beginning of zfcp in v2.6.0 history commit
ea127f975424 ("[PATCH] s390 (7/7): zfcp host adapter.").

Note: The FSF requests for forced port reopen could run into FSF request
timeouts due to other reasons. This would trigger an internal FCP device
recovery. Pending forced port reopen recoveries would get dismissed. So
some ports might not get fully reopened during this host reset handler.
However, subsequent I/O would trigger the above described escalation and
eventually all ports would be forced reopen to resolve any continuing FCP
request timeouts due to earlier bit errors.

Signed-off-by: Steffen Maier 
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Reviewed-by: Jens Remus 
Reviewed-by: Benjamin Block 
Signed-off-by: Martin K. Petersen 
Signed-off-by: Ben Hutchings

scsi: zfcp: fix rport unblock if deleted SCSI devices on Scsi_Host

2019-08-13T11:38:55+00:00

commit fe67888fc007a76b81e37da23ce5bd8fb95890b0 upstream.

An already deleted SCSI device can exist on the Scsi_Host and remain there
because something still holds a reference.  A new SCSI device with the same
H:C:T:L and FCP device, target port WWPN, and FCP LUN can be created.  When
we try to unblock an rport, we still find the deleted SCSI device and
return early because the zfcp_scsi_dev of that SCSI device is not
ZFCP_STATUS_COMMON_UNBLOCKED. Hence we miss to unblock the rport, even if
the new proper SCSI device would be in good state.

Therefore, skip deleted SCSI devices when iterating the sdevs of the shost.
[cf. __scsi_device_lookup{_by_target}() or scsi_device_get()]

The following abbreviated trace sequence can indicate such problem:

Area           : REC
Tag            : ersfs_3
LUN            : 0x4045400300000000
WWPN           : 0x50050763031bd327
LUN status     : 0x40000000     not ZFCP_STATUS_COMMON_UNBLOCKED
Ready count    : n		not incremented yet
Running count  : 0x00000000
ERP want       : 0x01
ERP need       : 0xc1		ZFCP_ERP_ACTION_NONE

Area           : REC
Tag            : ersfs_3
LUN            : 0x4045400300000000
WWPN           : 0x50050763031bd327
LUN status     : 0x41000000
Ready count    : n+1
Running count  : 0x00000000
ERP want       : 0x01
ERP need       : 0x01

...

Area           : REC
Level          : 4		only with increased trace level
Tag            : ertru_l
LUN            : 0x4045400300000000
WWPN           : 0x50050763031bd327
LUN status     : 0x40000000
Request ID     : 0x0000000000000000
ERP status     : 0x01800000
ERP step       : 0x1000
ERP action     : 0x01
ERP count      : 0x00

NOT followed by a trace record with tag "scpaddy"
for WWPN 0x50050763031bd327.

Signed-off-by: Steffen Maier 
Fixes: 6f2ce1c6af37 ("scsi: zfcp: fix rport unblock race with LUN recovery")
Reviewed-by: Jens Remus 
Reviewed-by: Benjamin Block 
Signed-off-by: Martin K. Petersen 
Signed-off-by: Ben Hutchings

s390/virtio: handle find on invalid queue gracefully

2019-07-09T21:04:13+00:00

commit 3438b2c039b4bf26881786a1f3450f016d66ad11 upstream.

A queue with a capacity of zero is clearly not a valid virtio queue.
Some emulators report zero queue size if queried with an invalid queue
index. Instead of crashing in this case let us just return -ENOENT. To
make that work properly, let us fix the notifier cleanup logic as well.

Signed-off-by: Halil Pasic 
Signed-off-by: Cornelia Huck 
Signed-off-by: Michael S. Tsirkin 
[bwh: Backported to 3.16: adjust filename]
Signed-off-by: Ben Hutchings