linux-stable.git/drivers/regulator, branch v6.9.4 Linux kernel stable tree regulator: tps6594-regulator: Correct multi-phase configuration 2024-06-12T09:39:41+00:00 Neha Malcom Francis n-francis@ti.com 2024-05-21T09:47:58+00:00 4a2c18d3bec3001b0f6f43946ad6be43051f64f6 [ Upstream commit 74b38cd77d3eb63c6d0ad9cf2ae59812ae54d3ee ] According to the TPS6594 PMIC Manual (linked) 8.3.2.1.4 Multi-Phase BUCK Regulator Configurations section, the PMIC ignores all the other bucks' except the primary buck's regulator registers. This is BUCK1 for configurations BUCK12, BUCK123 and BUCK1234 while it is BUCK3 for BUCK34. Correct the registers mapped for these configurations accordingly. Fixes: f17ccc5deb4d ("regulator: tps6594-regulator: Add driver for TI TPS6594 regulators") Link: https://www.ti.com/lit/gpn/tps6594-q1 Signed-off-by: Neha Malcom Francis <n-francis@ti.com> Link: https://msgid.link/r/20240521094758.2190331-1-n-francis@ti.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit 74b38cd77d3eb63c6d0ad9cf2ae59812ae54d3ee ]

According to the TPS6594 PMIC Manual (linked) 8.3.2.1.4 Multi-Phase BUCK
Regulator Configurations section, the PMIC ignores all the other bucks'
except the primary buck's regulator registers. This is BUCK1 for
configurations BUCK12, BUCK123 and BUCK1234 while it is BUCK3 for
BUCK34. Correct the registers mapped for these configurations
accordingly.

Fixes: f17ccc5deb4d ("regulator: tps6594-regulator: Add driver for TI TPS6594 regulators")
Link: https://www.ti.com/lit/gpn/tps6594-q1
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Link: https://msgid.link/r/20240521094758.2190331-1-n-francis@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
regulator: tps6287x: Force writing VSEL bit 2024-06-12T09:39:39+00:00 Matti Vaittinen mazziesaccount@gmail.com 2024-05-20T12:36:55+00:00 eda9ad82e6aa6cfef47cffe89333d3fa2ebb9877 [ Upstream commit 1ace99d7c7c4c801c0660246f741ff846a9b8e3c ] The data-sheet for TPS6287x-Q1 https://www.ti.com/lit/ds/symlink/tps62873-q1.pdf states at chapter 9.3.6.1 Output Voltage Range: "Note that every change to the VRANGE[1:0] bits must be followed by a write to the VSET register, even if the value of the VSET[7:0] bits does not change." The current implementation of the driver uses the regulator_set_voltage_sel_pickable_regmap() helper which further uses regmap_update_bits() to write the VSET-register. The regmap_update_bits() will not access the hardware if the new register value is same as old. It is worth noting that this is true also when the register is marked volatile, which I can't say is wrong because 'read-mnodify-write'-cycle with a volatile register is in any case something user should carefully consider. The 'range_applied_by_vsel'-flag in regulator desc was added to force the vsel register upodates by using regmap_write_bits(). This variant will always unconditionally write the bits to the hardware. It is worth noting that the vsel is now forced to be written to the hardware, whether the range was changed or not. This may cause a performance drop if users are wrtiting same voltage value repeteadly. It would be possible to read the range register to determine if it was changed, but this would be a performance issue for users who don't use reg cache for vsel. Always write the VSET register to the hardware regardless the cache. Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com> Fixes: 7b0518fbf2be ("regulator: Add support for TI TPS6287x regulators") Link: https://msgid.link/r/ZktD50C5twF1EuKu@fedora Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit 1ace99d7c7c4c801c0660246f741ff846a9b8e3c ]

The data-sheet for TPS6287x-Q1
https://www.ti.com/lit/ds/symlink/tps62873-q1.pdf
states at chapter 9.3.6.1 Output Voltage Range:

"Note that every change to the VRANGE[1:0] bits must be followed by a
write to the VSET register, even if the value of the VSET[7:0] bits does
not change."

The current implementation of the driver uses the
regulator_set_voltage_sel_pickable_regmap() helper which further uses
regmap_update_bits() to write the VSET-register. The
regmap_update_bits() will not access the hardware if the new register
value is same as old. It is worth noting that this is true also when the
register is marked volatile, which I can't say is wrong because
'read-mnodify-write'-cycle with a volatile register is in any case
something user should carefully consider.

The 'range_applied_by_vsel'-flag in regulator desc was added to force
the vsel register upodates by using regmap_write_bits(). This variant
will always unconditionally write the bits to the hardware.

It is worth noting that the vsel is now forced to be written to the
hardware, whether the range was changed or not. This may cause a
performance drop if users are wrtiting same voltage value repeteadly.

It would be possible to read the range register to determine if it was
changed, but this would be a performance issue for users who don't use
reg cache for vsel.

Always write the VSET register to the hardware regardless the cache.

Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Fixes: 7b0518fbf2be ("regulator: Add support for TI TPS6287x regulators")
Link: https://msgid.link/r/ZktD50C5twF1EuKu@fedora
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
regulator: pickable ranges: don't always cache vsel 2024-06-12T09:39:39+00:00 Matti Vaittinen mazziesaccount@gmail.com 2024-05-20T12:31:33+00:00 bc6d709844ee57dffd9e53e7ab2524e9d6edeb5e [ Upstream commit f4f4276f985a5aac7b310a4ed040b47e275e7591 ] Some PMICs treat the vsel_reg same as apply-bit. Eg, when voltage range is changed, the new voltage setting is not taking effect until the vsel register is written. Add a flag 'range_applied_by_vsel' to the regulator desc to indicate this behaviour and to force the vsel value to be written to hardware if range was changed, even if the old selector was same as the new one. Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com> Link: https://msgid.link/r/ZktCpcGZdgHWuN_L@fedora Signed-off-by: Mark Brown <broonie@kernel.org> Stable-dep-of: 1ace99d7c7c4 ("regulator: tps6287x: Force writing VSEL bit") Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit f4f4276f985a5aac7b310a4ed040b47e275e7591 ]

Some PMICs treat the vsel_reg same as apply-bit. Eg, when voltage range
is changed, the new voltage setting is not taking effect until the vsel
register is written.

Add a flag 'range_applied_by_vsel' to the regulator desc to indicate this
behaviour and to force the vsel value to be written to hardware if range
was changed, even if the old selector was same as the new one.

Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://msgid.link/r/ZktCpcGZdgHWuN_L@fedora
Signed-off-by: Mark Brown <broonie@kernel.org>
Stable-dep-of: 1ace99d7c7c4 ("regulator: tps6287x: Force writing VSEL bit")
Signed-off-by: Sasha Levin <sashal@kernel.org>
regulator: bd71828: Don't overwrite runtime voltages 2024-06-12T09:39:37+00:00 Matti Vaittinen mazziesaccount@gmail.com 2024-05-16T08:54:41+00:00 c87c9a8a66ea3a913b26bd9ec93ec14e6b5a3c63 [ Upstream commit 0f9f7c63c415e287cd57b5c98be61eb320dedcfc ] Some of the regulators on the BD71828 have common voltage setting for RUN/SUSPEND/IDLE/LPSR states. The enable control can be set for each state though. The driver allows setting the voltage values for these states via device-tree. As a side effect, setting the voltages for SUSPEND/IDLE/LPSR will also change the RUN level voltage which is not desired and can break the system. The comment in code reflects this behaviour, but it is likely to not make people any happier. The right thing to do is to allow setting the enable/disable state at SUSPEND/IDLE/LPSR via device-tree, but to disallow setting state specific voltages for those regulators. BUCK1 is a bit different. It only shares the SUSPEND and LPSR state voltages. The former behaviour of allowing to silently overwrite the SUSPEND state voltage by LPSR state voltage is also changed here so that the SUSPEND voltage is prioritized over LPSR voltage. Prevent setting PMIC state specific voltages for regulators which do not support it. Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com> Fixes: 522498f8cb8c ("regulator: bd71828: Basic support for ROHM bd71828 PMIC regulators") Link: https://msgid.link/r/e1883ae1e3ae5668f1030455d4750923561f3d68.1715848512.git.mazziesaccount@gmail.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit 0f9f7c63c415e287cd57b5c98be61eb320dedcfc ]

Some of the regulators on the BD71828 have common voltage setting for
RUN/SUSPEND/IDLE/LPSR states. The enable control can be set for each
state though.

The driver allows setting the voltage values for these states via
device-tree. As a side effect, setting the voltages for
SUSPEND/IDLE/LPSR will also change the RUN level voltage which is not
desired and can break the system.

The comment in code reflects this behaviour, but it is likely to not
make people any happier. The right thing to do is to allow setting the
enable/disable state at SUSPEND/IDLE/LPSR via device-tree, but to
disallow setting state specific voltages for those regulators.

BUCK1 is a bit different. It only shares the SUSPEND and LPSR state
voltages. The former behaviour of allowing to silently overwrite the
SUSPEND state voltage by LPSR state voltage is also changed here so that
the SUSPEND voltage is prioritized over LPSR voltage.

Prevent setting PMIC state specific voltages for regulators which do not
support it.

Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Fixes: 522498f8cb8c ("regulator: bd71828: Basic support for ROHM bd71828 PMIC regulators")
Link: https://msgid.link/r/e1883ae1e3ae5668f1030455d4750923561f3d68.1715848512.git.mazziesaccount@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
regulator: core: fix debugfs creation regression 2024-05-09T15:43:57+00:00 Johan Hovold johan+linaro@kernel.org 2024-05-09T13:33:04+00:00 2a4b49bb58123bad6ec0e07b02845f74c23d5e04 regulator_get() may sometimes be called more than once for the same consumer device, something which before commit dbe954d8f163 ("regulator: core: Avoid debugfs: Directory ... already present! error") resulted in errors being logged. A couple of recent commits broke the handling of such cases so that attributes are now erroneously created in the debugfs root directory the second time a regulator is requested and the log is filled with errors like: debugfs: File 'uA_load' in directory '/' already present! debugfs: File 'min_uV' in directory '/' already present! debugfs: File 'max_uV' in directory '/' already present! debugfs: File 'constraint_flags' in directory '/' already present! on any further calls. Fixes: 2715bb11cfff ("regulator: core: Fix more error checking for debugfs_create_dir()") Fixes: 08880713ceec ("regulator: core: Streamline debugfs operations") Cc: stable@vger.kernel.org Cc: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Johan Hovold <johan+linaro@kernel.org> Link: https://lore.kernel.org/r/20240509133304.8883-1-johan+linaro@kernel.org Signed-off-by: Mark Brown <broonie@kernel.org> 
regulator_get() may sometimes be called more than once for the same
consumer device, something which before commit dbe954d8f163 ("regulator:
core: Avoid debugfs: Directory ...  already present! error") resulted in
errors being logged.

A couple of recent commits broke the handling of such cases so that
attributes are now erroneously created in the debugfs root directory the
second time a regulator is requested and the log is filled with errors
like:

	debugfs: File 'uA_load' in directory '/' already present!
	debugfs: File 'min_uV' in directory '/' already present!
	debugfs: File 'max_uV' in directory '/' already present!
	debugfs: File 'constraint_flags' in directory '/' already present!

on any further calls.

Fixes: 2715bb11cfff ("regulator: core: Fix more error checking for debugfs_create_dir()")
Fixes: 08880713ceec ("regulator: core: Streamline debugfs operations")
Cc: stable@vger.kernel.org
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240509133304.8883-1-johan+linaro@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
regulator: rtq2208: Fix the BUCK ramp_delay range to maximum of 16mVstep/us 2024-05-01T14:11:37+00:00 Alina Yu alina_yu@richtek.com 2024-04-30T09:58:27+00:00 d1ef160b45a0010d1f1b3d601230457243a8f3e8 The maximum ramp up and down range of BUCK are shorten from 64mVstep/us to 16mVstep/us. Therefore, the RTQ2208_RAMP_VALUE_MAX_uV is modified to 16000uV in this version. Signed-off-by: Alina Yu <alina_yu@richtek.com> Link: https://lore.kernel.org/r/1777b18c0faa1f6b7196630e679a03362686c301.1714467553.git.alina_yu@richtek.com Signed-off-by: Mark Brown <broonie@kernel.org> 
The maximum ramp up and down range of BUCK are shorten
from 64mVstep/us to 16mVstep/us.
Therefore, the RTQ2208_RAMP_VALUE_MAX_uV is modified
to 16000uV in this version.

Signed-off-by: Alina Yu <alina_yu@richtek.com>
Link: https://lore.kernel.org/r/1777b18c0faa1f6b7196630e679a03362686c301.1714467553.git.alina_yu@richtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
regulator: vqmmc-ipq4019: fix module autoloading 2024-04-10T17:48:59+00:00 Krzysztof Kozlowski krzk@kernel.org 2024-04-10T17:26:15+00:00 68adb581a39ae63a0ed082c47f01fbbe515efa0e Add MODULE_DEVICE_TABLE(), so the module could be properly autoloaded based on the alias from of_device_id table. Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org> Link: https://msgid.link/r/20240410172615.255424-2-krzk@kernel.org Signed-off-by: Mark Brown <broonie@kernel.org> 
Add MODULE_DEVICE_TABLE(), so the module could be properly autoloaded
based on the alias from of_device_id table.

Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://msgid.link/r/20240410172615.255424-2-krzk@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
regulator: qcom-refgen: fix module autoloading 2024-04-10T17:48:58+00:00 Krzysztof Kozlowski krzk@kernel.org 2024-04-10T17:26:14+00:00 ddd3f34c10002e41ed3cd89c9bd8f1d05a22506a Add MODULE_DEVICE_TABLE(), so the module could be properly autoloaded based on the alias from of_device_id table. Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org> Link: https://msgid.link/r/20240410172615.255424-1-krzk@kernel.org Signed-off-by: Mark Brown <broonie@kernel.org> 
Add MODULE_DEVICE_TABLE(), so the module could be properly autoloaded
based on the alias from of_device_id table.

Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://msgid.link/r/20240410172615.255424-1-krzk@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
regulator: mt6360: De-capitalize devicetree regulator subnodes 2024-04-09T15:22:59+00:00 AngeloGioacchino Del Regno angelogioacchino.delregno@collabora.com 2024-04-09T14:44:38+00:00 d3cf8a17498dd9104c04ad28eeac3ef3339f9f9f The MT6360 regulator binding, the example in the MT6360 mfd binding, and the devicetree users of those bindings are rightfully declaring MT6360 regulator subnodes with non-capital names, and luckily without using the deprecated regulator-compatible property. With this driver declaring capitalized BUCKx/LDOx as of_match string for the node names, obviously no regulator gets probed: fix that by changing the MT6360_REGULATOR_DESC macro to add a "match" parameter which gets assigned to the of_match. Fixes: d321571d5e4c ("regulator: mt6360: Add support for MT6360 regulator") Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Link: https://msgid.link/r/20240409144438.410060-1-angelogioacchino.delregno@collabora.com Signed-off-by: Mark Brown <broonie@kernel.org> 
The MT6360 regulator binding, the example in the MT6360 mfd binding, and
the devicetree users of those bindings are rightfully declaring MT6360
regulator subnodes with non-capital names, and luckily without using the
deprecated regulator-compatible property.

With this driver declaring capitalized BUCKx/LDOx as of_match string for
the node names, obviously no regulator gets probed: fix that by changing
the MT6360_REGULATOR_DESC macro to add a "match" parameter which gets
assigned to the of_match.

Fixes: d321571d5e4c ("regulator: mt6360: Add support for MT6360 regulator")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://msgid.link/r/20240409144438.410060-1-angelogioacchino.delregno@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
regulator: irq_helpers: duplicate IRQ name 2024-04-08T12:58:57+00:00 Matti Vaittinen mazziesaccount@gmail.com 2024-04-07T07:35:21+00:00 7ab681ddedd4b6dd2b047c74af95221c5f827e1d The regulator IRQ helper requires caller to provide pointer to IRQ name which is kept in memory by caller. All other data passed to the helper in the regulator_irq_desc structure is copied. This can cause some confusion and unnecessary complexity. Make the regulator_irq_helper() to copy also the provided IRQ name information so caller can discard the name after the call to regulator_irq_helper() completes. Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com> Link: https://msgid.link/r/ZhJMuUYwaZbBXFGP@drtxq0yyyyyyyyyyyyydy-3.rev.dnainternet.fi Signed-off-by: Mark Brown <broonie@kernel.org> 
The regulator IRQ helper requires caller to provide pointer to IRQ name
which is kept in memory by caller. All other data passed to the helper
in the regulator_irq_desc structure is copied. This can cause some
confusion and unnecessary complexity.

Make the regulator_irq_helper() to copy also the provided IRQ name
information so caller can discard the name after the call to
regulator_irq_helper() completes.

Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://msgid.link/r/ZhJMuUYwaZbBXFGP@drtxq0yyyyyyyyyyyyydy-3.rev.dnainternet.fi
Signed-off-by: Mark Brown <broonie@kernel.org>