linux-stable.git/drivers/regulator, branch v3.16.40

regulator: tps65910: Work around silicon erratum SWCZ010

2017-02-23T03:54:03+00:00

commit 8f9165c981fed187bb483de84caf9adf835aefda upstream.

http://www.ti.com/lit/pdf/SWCZ010:
  DCDC o/p voltage can go higher than programmed value

Impact:
VDDI, VDD2, and VIO output programmed voltage level can go higher than
expected or crash, when coming out of PFM to PWM mode or using DVFS.

Description:
When DCDC CLK SYNC bits are 11/01:
* VIO 3-MHz oscillator is the source clock of the digital core and input
  clock of VDD1 and VDD2
* Turn-on of VDD1 and VDD2 HSD PFETis synchronized or at a constant
  phase shift
* Current pulled though VCC1+VCC2 is Iload(VDD1) + Iload(VDD2)
* The 3 HSD PFET will be turned-on at the same time, causing the highest
  possible switching noise on the application. This noise level depends
  on the layout, the VBAT level, and the load current. The noise level
  increases with improper layout.

When DCDC CLK SYNC bits are 00:
* VIO 3-MHz oscillator is the source clock of digital core
* VDD1 and VDD2 are running on their own 3-MHz oscillator
* Current pulled though VCC1+VCC2 average of Iload(VDD1) + Iload(VDD2)
* The switching noise of the 3 SMPS will be randomly spread over time,
  causing lower overall switching noise.

Workaround:
Set DCDCCTRL_REG[1:0]= 00.

Signed-off-by: Jan Remmet 
Signed-off-by: Mark Brown 
Signed-off-by: Ben Hutchings

regulator: s2mps11: Fix invalid selector mask and voltages for buck9

2016-06-15T20:29:21+00:00

commit 3b672623079bb3e5685b8549e514f2dfaa564406 upstream.

The buck9 regulator of S2MPS11 PMIC had incorrect vsel_mask (0xff
instead of 0x1f) thus reading entire register as buck9's voltage. This
effectively caused regulator core to interpret values as higher voltages
than they were and then to set real voltage much lower than intended.

The buck9 provides power to other regulators, including LDO13
and LDO19 which supply the MMC2 (SD card). On Odroid XU3/XU4 the lower
voltage caused SD card detection errors on Odroid XU3/XU4:
	mmc1: card never left busy state
	mmc1: error -110 whilst initialising SD card

During driver probe the regulator core was checking whether initial
voltage matches the constraints. With incorrect vsel_mask of 0xff and
default value of 0x50, the core interpreted this as 5 V which is outside
of constraints (3-3.775 V). Then the regulator core was adjusting the
voltage to match the constraints. With incorrect vsel_mask this new
voltage mapped to a vere low voltage in the driver.

Signed-off-by: Krzysztof Kozlowski 
Reviewed-by: Javier Martinez Canillas 
Tested-by: Javier Martinez Canillas 
Signed-off-by: Mark Brown 
[bwh: Backported to 3.16: s2mps11_buck9_ops was never combined with other
 macros here, so just change the n_voltages and vsel_mask fields]
Signed-off-by: Ben Hutchings

regulator: s5m8767: fix get_register() error handling

2016-04-30T22:05:48+00:00

commit e07ff9434167981c993a26d2edbbcb8e13801dbb upstream.

The s5m8767_pmic_probe() function calls s5m8767_get_register() to
read data without checking the return code, which produces a compile-time
warning when that data is accessed:

drivers/regulator/s5m8767.c: In function 's5m8767_pmic_probe':
drivers/regulator/s5m8767.c:924:7: error: 'enable_reg' may be used uninitialized in this function [-Werror=maybe-uninitialized]
drivers/regulator/s5m8767.c:944:30: error: 'enable_val' may be used uninitialized in this function [-Werror=maybe-uninitialized]

This changes the s5m8767_get_register() function to return a -EINVAL
not just for an invalid register number but also for an invalid
regulator number, as both would result in returning uninitialized
data. The s5m8767_pmic_probe() function is then changed accordingly
to fail on a read error, as all the other callers of s5m8767_get_register()
already do.

In practice this probably cannot happen, as we don't call
s5m8767_get_register() with invalid arguments, but the gcc
warning seems valid in principle, in terms writing safe
error checking.

Signed-off-by: Arnd Bergmann 
Fixes: 9c4c60554acf ("regulator: s5m8767: Convert to use regulator_[enable|disable|is_enabled]_regmap")
Signed-off-by: Mark Brown 
Signed-off-by: Ben Hutchings

regulator: pbias: Fix broken pbias disable functionality

2015-09-28T09:21:40+00:00

commit c329061be51bef655f28c9296093984c977aff85 upstream.

regulator_disable of pbias always writes '0' to the enable_reg.
However actual disable value of pbias regulator is not always '0'.
Fix it by populating the disable_val in pbias_reg_info for the
various platforms and assign it to the disable_val of
pbias regulator descriptor. This will be used by
regulator_disable_regmap while disabling pbias regulator.

Signed-off-by: Kishon Vijay Abraham I 
Signed-off-by: Mark Brown 
Signed-off-by: Luis Henriques

regulator: core: fix constraints output buffer

2015-07-15T09:00:25+00:00

commit a7068e3932eee8268c4ce4e080a338ee7b8a27bf upstream.

The buffer for condtraints debug isn't big enough to hold the output
in all cases. So fix this issue by increasing the buffer.

Signed-off-by: Stefan Wahren 
Signed-off-by: Mark Brown 
Signed-off-by: Luis Henriques

regulator: core: Fix enable GPIO reference counting

2015-03-30T10:11:07+00:00

commit 29d62ec5f87fbeec8413e2215ddad12e7f972e4c upstream.

Normally _regulator_do_enable() isn't called on an already-enabled
rdev.  That's because the main caller, _regulator_enable() always
calls _regulator_is_enabled() and only calls _regulator_do_enable() if
the rdev was not already enabled.

However, there is one caller of _regulator_do_enable() that doesn't
check: regulator_suspend_finish().  While we might want to make
regulator_suspend_finish() behave more like _regulator_enable(), it's
probably also a good idea to make _regulator_do_enable() robust if it
is called on an already enabled rdev.

At the moment, _regulator_do_enable() is _not_ robust for already
enabled rdevs if we're using an ena_pin.  Each time
_regulator_do_enable() is called for an rdev using an ena_pin the
reference count of the ena_pin is incremented even if the rdev was
already enabled.  This is not as intended because the ena_pin is for
something else: for keeping track of how many active rdevs there are
sharing the same ena_pin.

Here's how the reference counting works here:

* Each time _regulator_enable() is called we increment
  rdev->use_count, so _regulator_enable() calls need to be balanced
  with _regulator_disable() calls.

* There is no explicit reference counting in _regulator_do_enable()
  which is normally just a warapper around rdev->desc->ops->enable()
  with code for supporting delays.  It's not expected that the
  "ops->enable()" call do reference counting.

* Since regulator_ena_gpio_ctrl() does have reference counting
  (handling the sharing of the pin amongst multiple rdevs), we
  shouldn't call it if the current rdev is already enabled.

Note that as part of this we cleanup (remove) the initting of
ena_gpio_state in regulator_register().  In _regulator_do_enable(),
_regulator_do_disable() and _regulator_is_enabled() is is clear that
ena_gpio_state should be the state of whether this particular rdev has
requested the GPIO be enabled.  regulator_register() was initting it
as the actual state of the pin.

Fixes: 967cfb18c0e3 ("regulator: core: manage enable GPIO list")
Signed-off-by: Doug Anderson 
Signed-off-by: Mark Brown 
Signed-off-by: Luis Henriques

regulator: Only enable disabled regulators on resume

2015-03-30T10:11:06+00:00

commit 0548bf4f5ad6fc3bd93c4940fa48078b34609682 upstream.

The _regulator_do_enable() call ought to be a no-op when called on an
already-enabled regulator.  However, as an optimization
_regulator_enable() doesn't call _regulator_do_enable() on an already
enabled regulator.  That means we never test the case of calling
_regulator_do_enable() during normal usage and there may be hidden
bugs or warnings.  We have seen warnings issued by the tps65090 driver
and bugs when using the GPIO enable pin.

Let's match the same optimization that _regulator_enable() in
regulator_suspend_finish().  That may speed up suspend/resume and also
avoids exposing hidden bugs.

[Use much clearer commit message from Doug Anderson]

Signed-off-by: Javier Martinez Canillas 
Signed-off-by: Mark Brown 
Signed-off-by: Luis Henriques

regulator: core: fix race condition in regulator_put()

2015-02-04T10:58:01+00:00

commit 83b0302d347a49f951e904184afe57ac3723476e upstream.

The regulator framework maintains a list of consumer regulators
for a regulator device and protects it from concurrent access using
the regulator device's mutex lock.

In the case of regulator_put() the consumer is removed and regulator
device's parameters are updated without holding the regulator device's
mutex. This would lead to a race condition between the regulator_put()
and any function which traverses the consumer list or modifies regulator
device's parameters.
Fix this race condition by holding the regulator device's mutex in case
of regulator_put.

Signed-off-by: Ashay Jaiswal 
Signed-off-by: Mark Brown 
Signed-off-by: Luis Henriques

regulator: anatop: Set default voltage selector for vddpu

2015-01-05T13:33:40+00:00

commit fe08be3ec8672ed92b3ed1b85810df9fa0f98931 upstream.

The code reads the default voltage selector from its register. If the
bootloader disables the regulator, the default voltage selector will be
0 which results in faulty behaviour of this regulator driver.

This patch sets a default voltage selector for vddpu if it is not set in
the register.

Signed-off-by: Markus Pargmann 
Signed-off-by: Mark Brown 
Signed-off-by: Luis Henriques

regulator: max77693: Fix use of uninitialized regulator config

2014-11-14T15:19:55+00:00

commit ca0c37a0b489bb14bf3e1549e7a8d0c9a17f4919 upstream.

Driver allocated on stack struct regulator_config but didn't initialize
it fully. Few fields (driver_data, ena_gpio) were left untouched. This
lead to using random ena_gpio values as GPIOs for max77693 regulators.

On occasion these values could match real GPIO numbers leading to
interfering with other drivers and to unsuccessful enable/disable of
regulator.

Signed-off-by: Krzysztof Kozlowski 
Fixes: 80b022e29bfd ("regulator: max77693: Add max77693 regualtor driver.")
Signed-off-by: Mark Brown 
Signed-off-by: Luis Henriques