commit 42ab0f3915f22728f54bb1f3c0dcf38ab2335b5b upstream.

The second range of this particular regulator,
starts at 1.60V, not as 1.55V as it was originally
implied by code.

Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 5b919f3ebb533cbe400664837e24f66a0836b907 upstream.

WM5110/8280 devices do not support bypass mode for LDO1 so remove
the bypass callbacks registered with regulator core.

Signed-off-by: Nikesh Oswal <nikesh@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Correct the the config register for LDO1.

Fixes: 90e7d5262796 (regulator: tps65218: Add Regulator driver for
TPS65218 PMIC)
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: <stable@vger.kernel.org> # v3.15

Add the missing of_node assignment in probe.

Fixes: 90e7d5262796 (regulator: tps65218: Add Regulator driver for TPS65218 PMIC)
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: <stable@vger.kernel.org> # v3.15

When setting up .enable_reg for an SMPS regulator, presumably we should
call PALMAS_BASE_TO_REG(PALMAS_SMPS_BASE, ...) rather than using
LDO_BASE. This change makes the LCD panel and HDMI work again on the
NVIDIA Dalmore board anyway.

Fixes: 318dbb02b50c ("regulator: palmas: Fix SMPS enable/disable/is_enabled")
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Nishanth Menon <nm@ti.com>
Tested-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>

The vbus regulator was not getting its name set. This results
in the sysfs entry being empty. The lack of a bcm590xx_regs[]
table entry also upsets Coverity runs. Add the table entry
so the name gets set properly.

Signed-off-by: Graham Williams <graham.williams@linaro.org>
Acked-by: Matt Porter <mporter@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>

We use regmap regulator ops to enable/disable and check if regulator
is enabled for various SMPS. However, these depend on valid
enable_reg, enable_mask and enable_value in regulator descriptor.

Currently we do not populate these for SMPS other than SMPS10, this
results in spurious results as regmap assumes that the values are
valid and ends up reading register 0x0 RTC:SECONDS_REG on Palmas
variants that do have RTC! To fix this, we update proper parameters
for the descriptor fields.

Further, we want to ensure the behavior consistent with logic
prior to commit dbabd624d4eec50b6, where, once you do a set_mode,
enable/disable ensure the logic remains consistent and configures
Palmas to the configuration that we set with set_mode (since the
configuration register is common). To do this, we can rely on the
regulator core's regulator_register behavior where the regulator
descriptor pointer provided by the regulator driver is stored. (no
reallocation and copy is done). This lets us update the enable_value
post registration, to remain consistent with the mode we configure as
part of set_mode.

Fixes: dbabd624d4eec50b6 ("regulator: palmas: Reemove open coded functions with helper functions")
Reported-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>

of_find_node_by_name() walks the allnodes list, and can thus walk
outside of the parent node. Use of_get_child_by_name() instead.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>