The remove function uses __devexit, so the .remove assignment needs
__devexit_p() to fix a build error with hotplug disabled.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
CC: Liam Girdwood <lrg@slimlogic.co.uk>
CC: Mike Rapoport <mike@compulab.co.il>
CC: Eric Miao <eric.miao@marvell.com>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

Default voltage constraints were being provided for fixed voltage
regulator where board constraints were not provided but these constraints
used INT_MIN as the default minimum voltage which is not a valid value
since it is less than zero. Use 1uV instead.

Also set the default values we set in the constraints themselves since
otherwise the max_uV constraint we determine will not be stored in the
actual constraint strucutre and will therefore not be used.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

This seems to be fallout from last October's regulator core rework.
It got noticed only because of recent regulator framework changes.

Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

During regulator registration, any error after device_register() will
cause a double-free on the struct regulator_dev 'rdev'.  The bug is in
drivers/regulator/core.c:regulator_register():

...
scrub:
	device_unregister(&rdev->dev);
clean:
	kfree(rdev);                           <---
	rdev = ERR_PTR(ret);
	goto out;
...

device_unregister() calls regulator_dev_release() which frees rdev.  The
subsequent kfree corrupts memory and causes some OMAP3 systems to oops on
boot in regulator_get().

Applies against 2.6.30-rc3.

Signed-off-by: Paul Walmsley <paul@pwsan.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

When regulator_desc->type is something different from REGULATOR_VOLTAGE or REGULATOR_CURRENT
the if should probably return ERR_PTR(-EINVAL)

The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)

@@ expression E; constant C; @@
(
- !E == C
+ E != C
)

Signed-off-by: Diego Liziero <diegoliz@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

I removed the extra semi-colon and indented the return statement.

The unreachable code was found by smatch (http://repo.or.cz/w/smatch.git).
The patch was compile tested.

regards,
dan carpenter

Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

TWL4030 and TWL5030 support 3.0V on VAUX3.

Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>

At present it is not possible for machine constraints to disable
regulators which have been left on when the system starts, for example
as a result of fixed default configurations in hardware. This means that
power may be wasted by these regulators if they are not in use.

Provide intial support for this with a late_initcall which will disable
any unused regulators if the machine has enabled this feature by calling
regulator_has_full_constraints(). If this has not been called then print
a warning to encourage users to fully specify their constraints so that
we can change this to be the default behaviour in future.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

Don't set use_count for regulators that are enabled at boot since this
stops the supply being disabled by well-behaved consumers which do
balanced enables and disabled. Any consumers which don't do disables
which are not matched by enables are unable to share regulators - shared
regulators are the common case so the API should facilitate them.

Consumers that want to disable regulators that are enabled when they
start have two options:

 - Do a regulator_enable() prior to the disable to bring the use count
   in sync with the hardware state; this will ensure that if the
   regulator was enabled by another driver then this consumer will play
   nicely with it.
 - Use regulator_force_disable(); this explicitly bypasses any checks
   done by the core and documents the inability of the driver to share
   the supply.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>