Pull regulator fixes from Mark Brown:
 "A small set of fixes for mostly minor issues here, the only real code
  ones are Wen Yang's fixes for error handling in the core and Christian
  Marussi's list_voltage() change which is a fix for disruptively bad
  performance for regulators with continuous voltage control (which are
  rare)"

* tag 'regulator-fix-v5.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
  regulator: rn5t618: fix module aliases
  regulator: max77650: add of_match table
  regulator: core: avoid unneeded .list_voltage calls
  regulator: s5m8767: Fix a warning message
  regulator: core: fix regulator_register() error paths to properly release rdev
  regulator: fix use after free issue

Inside machine_constraints_voltage() a loop is in charge of verifying that
each of the defined voltages are within the configured constraints and
that those constraints are in fact compatible with the available voltages'
list.

When the registered regulator happens to be defined with a wide range of
possible voltages the above O(n) loop can be costly.
Moreover since this behaviour is triggered during the registration process,
it means also that it can be easily triggered at probe time, slowing down
considerably some module loading.

On the other side if such wide range of voltage values happens to be also
continuous and without discontinuity of any kind, the above potentially
cumbersome operation is also useless.

For these reasons, avoid such .list_voltage poll loop when regulator is
described as 'continuous_voltage_range' as is, indeed, similarly already
done inside regulator_is_supported_voltage().

Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Link: https://lore.kernel.org/r/20191209125239.46054-1-cristian.marussi@arm.com
Signed-off-by: Mark Brown <broonie@kernel.org>

There are several issues with the error handling code of
the regulator_register() function:
        ret = device_register(&rdev->dev);
        if (ret != 0) {
                put_device(&rdev->dev); --> rdev released
                goto unset_supplies;
        }
...
unset_supplies:
...
        unset_regulator_supplies(rdev); --> use-after-free
...
clean:
        if (dangling_of_gpiod)
                gpiod_put(config->ena_gpiod);
        kfree(rdev);                     --> double free

We add a variable to record the failure of device_register() and
move put_device() down a bit to avoid the above issues.

Fixes: c438b9d01736 ("regulator: core: Move registration of regulator device")
Signed-off-by: Wen Yang <wenyang@linux.alibaba.com>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/r/20191201030250.38074-1-wenyang@linux.alibaba.com
Signed-off-by: Mark Brown <broonie@kernel.org>

This is caused by dereferencing 'rdev' after put_device() in
the _regulator_get()/_regulator_put() functions.
This patch just moves the put_device() down a bit to avoid the
issue.

Signed-off-by: Wen Yang <wenyang@linux.alibaba.com>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/r/20191124145835.25999-1-wenyang@linux.alibaba.com
Signed-off-by: Mark Brown <broonie@kernel.org>

Boot-on regulators are always kept on because their use_count value
is now incremented at boot time and never cleaned.

Only increment count value for alway-on regulators.
regulator_late_cleanup() is now able to power off boot-on regulators
when unused.

Fixes: 05f224ca6693 ("regulator: core: Clean enabling always-on regulators + their supplies")
Signed-off-by: Pascal Paillet <p.paillet@st.com>
Link: https://lore.kernel.org/r/20191113102737.27831-1-p.paillet@st.com
Signed-off-by: Mark Brown <broonie@kernel.org>

device_link_add() might not always succeed depending on the type of
device link and the rest of the dependencies in the system. If
device_link_add() didn't succeed, then we shouldn't try to remove the
link later on as it might remove a link someone else created.

Signed-off-by: Saravana Kannan <saravanak@google.com>
Link: https://lore.kernel.org/r/20191115000438.45970-1-saravanak@google.com
Signed-off-by: Mark Brown <broonie@kernel.org>

The generic voltage balancer doesn't work correctly if one of regulator
couples turns off. Currently there are no users in kernel for that case,
although let's explicitly show that this case is unsupported for those who
will try to use that feature.

Link: https://lore.kernel.org/linux-samsung-soc/20191008170503.yd6GscYPLxjgrXqDuCO7AJc6i6egNZGJkVWHLlCxvA4@z/
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20191025002240.25288-2-digetx@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>

This patch fixes memory leak which should happen if regulator's coupling
fails to initialize.

Fixes: d8ca7d184b33 ("regulator: core: Introduce API for regulators coupling customization")
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20191025002240.25288-1-digetx@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>

Sometimes it can happen that the regulator_of_get_init_data() can't
retrieve the config due to a not probed device the regulator depends on.
Fix that by checking the return value of of_parse_cb() and return
EPROBE_DEFER in such cases.

Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Link: https://lore.kernel.org/r/20190917154021.14693-4-m.felsch@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>