linux-stable.git/drivers/pwm, branch v3.16.78

pwm: tiehrpwm: Update shadow register for disabling PWMs

2019-09-23T20:11:34+00:00

commit b00ef53053191d3025c15e8041699f8c9d132daf upstream.

It must be made sure that immediate mode is not already set, when
modifying shadow register value in ehrpwm_pwm_disable(). Otherwise
modifications to the action-qualifier continuous S/W force
register(AQSFRC) will be done in the active register.
This may happen when both channels are being disabled. In this case,
only the first channel state will be recorded as disabled in the shadow
register. Later, when enabling the first channel again, the second
channel would be enabled as well. Setting RLDCSF to zero, first, ensures
that the shadow register is updated as desired.

Fixes: 38dabd91ff0b ("pwm: tiehrpwm: Fix disabling of output of PWMs")
Signed-off-by: Christoph Vogtländer 
[vigneshr@ti.com: Improve commit message]
Signed-off-by: Vignesh Raghavendra 
Signed-off-by: Thierry Reding 
Signed-off-by: Ben Hutchings

pwm: Fix deadlock warning when removing PWM device

2019-09-23T20:11:34+00:00

commit 347ab9480313737c0f1aaa08e8f2e1a791235535 upstream.

This patch fixes deadlock warning if removing PWM device
when CONFIG_PROVE_LOCKING is enabled.

This issue can be reproceduced by the following steps on
the R-Car H3 Salvator-X board if the backlight is disabled:

 # cd /sys/class/pwm/pwmchip0
 # echo 0 > export
 # ls
 device  export  npwm  power  pwm0  subsystem  uevent  unexport
 # cd device/driver
 # ls
 bind  e6e31000.pwm  uevent  unbind
 # echo e6e31000.pwm > unbind

[   87.659974] ======================================================
[   87.666149] WARNING: possible circular locking dependency detected
[   87.672327] 5.0.0 #7 Not tainted
[   87.675549] ------------------------------------------------------
[   87.681723] bash/2986 is trying to acquire lock:
[   87.686337] 000000005ea0e178 (kn->count#58){++++}, at: kernfs_remove_by_name_ns+0x50/0xa0
[   87.694528]
[   87.694528] but task is already holding lock:
[   87.700353] 000000006313b17c (pwm_lock){+.+.}, at: pwmchip_remove+0x28/0x13c
[   87.707405]
[   87.707405] which lock already depends on the new lock.
[   87.707405]
[   87.715574]
[   87.715574] the existing dependency chain (in reverse order) is:
[   87.723048]
[   87.723048] -> #1 (pwm_lock){+.+.}:
[   87.728017]        __mutex_lock+0x70/0x7e4
[   87.732108]        mutex_lock_nested+0x1c/0x24
[   87.736547]        pwm_request_from_chip.part.6+0x34/0x74
[   87.741940]        pwm_request_from_chip+0x20/0x40
[   87.746725]        export_store+0x6c/0x1f4
[   87.750820]        dev_attr_store+0x18/0x28
[   87.754998]        sysfs_kf_write+0x54/0x64
[   87.759175]        kernfs_fop_write+0xe4/0x1e8
[   87.763615]        __vfs_write+0x40/0x184
[   87.767619]        vfs_write+0xa8/0x19c
[   87.771448]        ksys_write+0x58/0xbc
[   87.775278]        __arm64_sys_write+0x18/0x20
[   87.779721]        el0_svc_common+0xd0/0x124
[   87.783986]        el0_svc_compat_handler+0x1c/0x24
[   87.788858]        el0_svc_compat+0x8/0x18
[   87.792947]
[   87.792947] -> #0 (kn->count#58){++++}:
[   87.798260]        lock_acquire+0xc4/0x22c
[   87.802353]        __kernfs_remove+0x258/0x2c4
[   87.806790]        kernfs_remove_by_name_ns+0x50/0xa0
[   87.811836]        remove_files.isra.1+0x38/0x78
[   87.816447]        sysfs_remove_group+0x48/0x98
[   87.820971]        sysfs_remove_groups+0x34/0x4c
[   87.825583]        device_remove_attrs+0x6c/0x7c
[   87.830197]        device_del+0x11c/0x33c
[   87.834201]        device_unregister+0x14/0x2c
[   87.838638]        pwmchip_sysfs_unexport+0x40/0x4c
[   87.843509]        pwmchip_remove+0xf4/0x13c
[   87.847773]        rcar_pwm_remove+0x28/0x34
[   87.852039]        platform_drv_remove+0x24/0x64
[   87.856651]        device_release_driver_internal+0x18c/0x21c
[   87.862391]        device_release_driver+0x14/0x1c
[   87.867175]        unbind_store+0xe0/0x124
[   87.871265]        drv_attr_store+0x20/0x30
[   87.875442]        sysfs_kf_write+0x54/0x64
[   87.879618]        kernfs_fop_write+0xe4/0x1e8
[   87.884055]        __vfs_write+0x40/0x184
[   87.888057]        vfs_write+0xa8/0x19c
[   87.891887]        ksys_write+0x58/0xbc
[   87.895716]        __arm64_sys_write+0x18/0x20
[   87.900154]        el0_svc_common+0xd0/0x124
[   87.904417]        el0_svc_compat_handler+0x1c/0x24
[   87.909289]        el0_svc_compat+0x8/0x18
[   87.913378]
[   87.913378] other info that might help us debug this:
[   87.913378]
[   87.921374]  Possible unsafe locking scenario:
[   87.921374]
[   87.927286]        CPU0                    CPU1
[   87.931808]        ----                    ----
[   87.936331]   lock(pwm_lock);
[   87.939293]                                lock(kn->count#58);
[   87.945120]                                lock(pwm_lock);
[   87.950599]   lock(kn->count#58);
[   87.953908]
[   87.953908]  *** DEADLOCK ***
[   87.953908]
[   87.959821] 4 locks held by bash/2986:
[   87.963563]  #0: 00000000ace7bc30 (sb_writers#6){.+.+}, at: vfs_write+0x188/0x19c
[   87.971044]  #1: 00000000287991b2 (&of->mutex){+.+.}, at: kernfs_fop_write+0xb4/0x1e8
[   87.978872]  #2: 00000000f739d016 (&dev->mutex){....}, at: device_release_driver_internal+0x40/0x21c
[   87.988001]  #3: 000000006313b17c (pwm_lock){+.+.}, at: pwmchip_remove+0x28/0x13c
[   87.995481]
[   87.995481] stack backtrace:
[   87.999836] CPU: 0 PID: 2986 Comm: bash Not tainted 5.0.0 #7
[   88.005489] Hardware name: Renesas Salvator-X board based on r8a7795 ES1.x (DT)
[   88.012791] Call trace:
[   88.015235]  dump_backtrace+0x0/0x190
[   88.018891]  show_stack+0x14/0x1c
[   88.022204]  dump_stack+0xb0/0xec
[   88.025514]  print_circular_bug.isra.32+0x1d0/0x2e0
[   88.030385]  __lock_acquire+0x1318/0x1864
[   88.034388]  lock_acquire+0xc4/0x22c
[   88.037958]  __kernfs_remove+0x258/0x2c4
[   88.041874]  kernfs_remove_by_name_ns+0x50/0xa0
[   88.046398]  remove_files.isra.1+0x38/0x78
[   88.050487]  sysfs_remove_group+0x48/0x98
[   88.054490]  sysfs_remove_groups+0x34/0x4c
[   88.058580]  device_remove_attrs+0x6c/0x7c
[   88.062671]  device_del+0x11c/0x33c
[   88.066154]  device_unregister+0x14/0x2c
[   88.070070]  pwmchip_sysfs_unexport+0x40/0x4c
[   88.074421]  pwmchip_remove+0xf4/0x13c
[   88.078163]  rcar_pwm_remove+0x28/0x34
[   88.081906]  platform_drv_remove+0x24/0x64
[   88.085996]  device_release_driver_internal+0x18c/0x21c
[   88.091215]  device_release_driver+0x14/0x1c
[   88.095478]  unbind_store+0xe0/0x124
[   88.099048]  drv_attr_store+0x20/0x30
[   88.102704]  sysfs_kf_write+0x54/0x64
[   88.106359]  kernfs_fop_write+0xe4/0x1e8
[   88.110275]  __vfs_write+0x40/0x184
[   88.113757]  vfs_write+0xa8/0x19c
[   88.117065]  ksys_write+0x58/0xbc
[   88.120374]  __arm64_sys_write+0x18/0x20
[   88.124291]  el0_svc_common+0xd0/0x124
[   88.128034]  el0_svc_compat_handler+0x1c/0x24
[   88.132384]  el0_svc_compat+0x8/0x18

The sysfs unexport in pwmchip_remove() is completely asymmetric
to what we do in pwmchip_add_with_polarity() and commit 0733424c9ba9
("pwm: Unexport children before chip removal") is a strong indication
that this was wrong to begin with. We should just move
pwmchip_sysfs_unexport() where it belongs, which is right after
pwmchip_sysfs_unexport_children(). In that case, we do not need
separate functions anymore either.

We also really want to remove sysfs irrespective of whether or not
the chip will be removed as a result of pwmchip_remove(). We can only
assume that the driver will be gone after that, so we shouldn't leave
any dangling sysfs files around.

This warning disappears if we move pwmchip_sysfs_unexport() to
the top of pwmchip_remove(), pwmchip_sysfs_unexport_children().
That way it is also outside of the pwm_lock section, which indeed
doesn't seem to be needed.

Moving the pwmchip_sysfs_export() call outside of that section also
seems fine and it'd be perfectly symmetric with pwmchip_remove() again.

So, this patch fixes them.

Signed-off-by: Phong Hoang 
[shimoda: revise the commit log and code]
Fixes: 76abbdde2d95 ("pwm: Add sysfs interface")
Fixes: 0733424c9ba9 ("pwm: Unexport children before chip removal")
Signed-off-by: Yoshihiro Shimoda 
Tested-by: Hoan Nguyen An 
Reviewed-by: Geert Uytterhoeven 
Reviewed-by: Simon Horman 
Reviewed-by: Uwe Kleine-König 
Signed-off-by: Thierry Reding 
Signed-off-by: Ben Hutchings

pwm: tiehrpwm: Fix disabling of output of PWMs

2018-12-16T22:08:13+00:00

commit 38dabd91ff0bde33352ca3cc65ef515599b77a05 upstream.

pwm-tiehrpwm driver disables PWM output by putting it in low output
state via active AQCSFRC register in ehrpwm_pwm_disable(). But, the
AQCSFRC shadow register is not updated. Therefore, when shadow AQCSFRC
register is re-enabled in ehrpwm_pwm_enable() (say to enable second PWM
output), previous settings are lost as shadow register value is loaded
into active register. This results in things like PWMA getting enabled
automatically, when PWMB is enabled and vice versa. Fix this by
updating AQCSFRC shadow register as well during ehrpwm_pwm_disable().

Fixes: 19891b20e7c2 ("pwm: pwm-tiehrpwm: PWM driver support for EHRPWM")
Signed-off-by: Vignesh R 
Signed-off-by: Thierry Reding 
Signed-off-by: Ben Hutchings

pwm: tiehrpwm: Don't use emulation mode bits to control PWM output

2018-12-16T22:08:13+00:00

commit aa49d628f6e016bcec8c6f8e704b9b18ee697329 upstream.

As per AM335x TRM SPRUH73P "15.2.2.11 ePWM Behavior During Emulation",
TBCTL[15:14] only have effect during emulation suspend events (IOW,
to stop PWM when debugging using a debugger). These bits have no effect
on PWM output during normal running of system. Hence, remove code
accessing these bits as they have no role in enabling/disabling PWMs.

Fixes: 19891b20e7c2 ("pwm: pwm-tiehrpwm: PWM driver support for EHRPWM")
Signed-off-by: Vignesh R 
Signed-off-by: Thierry Reding 
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings

pwm: lpss: platform: Save/restore the ctrl register over a suspend/resume

2018-11-20T18:05:11+00:00

commit 1d375b58c12f08d8570b30b865def4734517f04f upstream.

On some devices the contents of the ctrl register get lost over a
suspend/resume and the PWM comes back up disabled after the resume.

This is seen on some Bay Trail devices with the PWM in ACPI enumerated
mode, so it shows up as a platform device instead of a PCI device.

If we still think it is enabled and then try to change the duty-cycle
after this, we end up with a "PWM_SW_UPDATE was not cleared" error and
the PWM is stuck in that state from then on.

This commit adds suspend and resume pm callbacks to the pwm-lpss-platform
code, which save/restore the ctrl register over a suspend/resume, fixing
this.

Note that:

1) There is no need to do this over a runtime suspend, since we
only runtime suspend when disabled and then we properly set the enable
bit and reprogram the timings when we re-enable the PWM.

2) This may be happening on more systems then we realize, but has been
covered up sofar by a bug in the acpi-lpss.c code which was save/restoring
the regular device registers instead of the lpss private registers due to
lpss_device_desc.prv_offset not being set. This is fixed by a later patch
in this series.

Signed-off-by: Hans de Goede 
Reviewed-by: Andy Shevchenko 
Signed-off-by: Thierry Reding 
[bwh: Backported to 3.16:
 - pwm-lpss is a single module, so make the new functions static
 - Only one PWM per chip is supported; remove the npwm assertion and loops
 - Adjust filenames, context]
Signed-off-by: Ben Hutchings

pwm: tiehrpwm: fix clock imbalance in probe error path

2017-11-26T13:50:22+00:00

commit e2b5602af76dec75f474e4173afb4215007ecfa5 upstream.

Make sure to unprepare the clock before returning on late probe errors.

Fixes: b388f15fd14c ("pwm: pwm-tiehrpwm: Use clk_enable/disable instead clk_prepare/unprepare.")
Signed-off-by: Johan Hovold 
Signed-off-by: Thierry Reding 
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings

pwm: tiehrpwm: Fix runtime PM imbalance at unbind

2017-11-26T13:50:22+00:00

commit c7fdd3f52944b81d807ce7a5fde7d1ca8a2a0919 upstream.

Remove unbalanced RPM put at driver unbind which resulted in a negative
usage count.

Fixes: 19891b20e7c2 ("pwm: pwm-tiehrpwm: PWM driver support for EHRPWM")
Signed-off-by: Johan Hovold 
Signed-off-by: Thierry Reding 
Signed-off-by: Ben Hutchings

pwm: Fix device reference leak

2017-02-23T03:54:40+00:00

commit 0e1614ac84f1719d87bed577963bb8140d0c9ce8 upstream.

Make sure to drop the reference to the parent device taken by
class_find_device() after "unexporting" any children when deregistering
a PWM chip.

Fixes: 0733424c9ba9 ("pwm: Unexport children before chip removal")
Signed-off-by: Johan Hovold 
Signed-off-by: Thierry Reding 
Signed-off-by: Ben Hutchings

pwm: Unexport children before chip removal

2017-02-23T03:53:57+00:00

commit 0733424c9ba9f42242409d1ece780777272f7ea1 upstream.

Exported pwm channels aren't removed before the pwmchip and are
leaked. This results in invalid sysfs files. This fix removes
all exported pwm channels before chip removal.

Signed-off-by: David Hsu 
Fixes: 76abbdde2d95 ("pwm: Add sysfs interface")
Signed-off-by: Thierry Reding 
Signed-off-by: Ben Hutchings

pwm: Fix period and polarity in pwm_get() for non-perfect matches

2014-10-05T20:40:52+00:00

commit d717ea73e36dd5659640fae82605ad85c4117f4d upstream.

If pwm_get() finds a look-up entry with a perfect match (both dev_id and
con_id match), the loop is aborted, and "p" still points to the correct
struct pwm_lookup.

If only an entry with a matching dev_id or con_id is found, the loop
terminates after traversing the whole list, and "p" now points to
arbitrary memory, not part of the pwm_lookup list.
Then pwm_set_period() and pwm_set_polarity() will set random values for
period resp. polarity.

To fix this, save period and polarity when finding a new best match,
just like is done for chip (for the provider) and index.

This fixes the LCD backlight on r8a7740/armadillo-legacy, which was fed
period 0 and polarity -1068821144 instead of 33333 resp. 1.

Fixes: 3796ce1d4d4b ("pwm: add period and polarity to struct pwm_lookup")
Signed-off-by: Geert Uytterhoeven 
Signed-off-by: Thierry Reding 
Signed-off-by: Greg Kroah-Hartman